[PATCH 16/16] arm: Remove mx31pdk_defconfig board
Jagan Teki
jagan at amarulasolutions.com
Sat Jun 13 15:54:55 CEST 2020
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Patch-cc: Magnus Lilja <lilja.magnus at gmail.com>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
arch/arm/mach-imx/mx3/Kconfig | 12 --
board/freescale/mx31pdk/Kconfig | 15 ---
board/freescale/mx31pdk/MAINTAINERS | 6 -
board/freescale/mx31pdk/Makefile | 11 --
board/freescale/mx31pdk/lowlevel_init.S | 76 -------------
board/freescale/mx31pdk/mx31pdk.c | 119 --------------------
configs/mx31pdk_defconfig | 40 -------
include/configs/mx31pdk.h | 141 ------------------------
8 files changed, 420 deletions(-)
delete mode 100644 board/freescale/mx31pdk/Kconfig
delete mode 100644 board/freescale/mx31pdk/MAINTAINERS
delete mode 100644 board/freescale/mx31pdk/Makefile
delete mode 100644 board/freescale/mx31pdk/lowlevel_init.S
delete mode 100644 board/freescale/mx31pdk/mx31pdk.c
delete mode 100644 configs/mx31pdk_defconfig
delete mode 100644 include/configs/mx31pdk.h
diff --git a/arch/arm/mach-imx/mx3/Kconfig b/arch/arm/mach-imx/mx3/Kconfig
index 5028d5ea56..16bdbe7a2b 100644
--- a/arch/arm/mach-imx/mx3/Kconfig
+++ b/arch/arm/mach-imx/mx3/Kconfig
@@ -3,17 +3,6 @@ if ARCH_MX31
config MX31
bool
default y
-choice
- prompt "MX31 board select"
- optional
-
-config TARGET_MX31PDK
- bool "Support the i.MX31 PDK board from Freescale/NXP"
- select BOARD_EARLY_INIT_F
- select BOARD_LATE_INIT
- select SUPPORT_SPL
-
-endchoice
config MX31_HCLK_FREQ
int "i.MX31 HCLK frequency"
@@ -29,6 +18,5 @@ config MX31_CLK32
Frequency in Hz of the low frequency input clock. Typically
32768 or 32000 Hz.
-source "board/freescale/mx31pdk/Kconfig"
endif
diff --git a/board/freescale/mx31pdk/Kconfig b/board/freescale/mx31pdk/Kconfig
deleted file mode 100644
index 055545c930..0000000000
--- a/board/freescale/mx31pdk/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_MX31PDK
-
-config SYS_BOARD
- default "mx31pdk"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_SOC
- default "mx31"
-
-config SYS_CONFIG_NAME
- default "mx31pdk"
-
-endif
diff --git a/board/freescale/mx31pdk/MAINTAINERS b/board/freescale/mx31pdk/MAINTAINERS
deleted file mode 100644
index ec2a32063b..0000000000
--- a/board/freescale/mx31pdk/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MX31PDK BOARD
-M: Magnus Lilja <lilja.magnus at gmail.com>
-S: Maintained
-F: board/freescale/mx31pdk/
-F: include/configs/mx31pdk.h
-F: configs/mx31pdk_defconfig
diff --git a/board/freescale/mx31pdk/Makefile b/board/freescale/mx31pdk/Makefile
deleted file mode 100644
index 7edc60f0d2..0000000000
--- a/board/freescale/mx31pdk/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2008 Magnus Lilja <lilja.magnus at gmail.com>
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-
-ifdef CONFIG_SPL_BUILD
-obj-y += lowlevel_init.o
-endif
-obj-y += mx31pdk.o
diff --git a/board/freescale/mx31pdk/lowlevel_init.S b/board/freescale/mx31pdk/lowlevel_init.S
deleted file mode 100644
index d78459faf6..0000000000
--- a/board/freescale/mx31pdk/lowlevel_init.S
+++ /dev/null
@@ -1,76 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009 Magnus Lilja <lilja.magnus at gmail.com>
- */
-
-#include <config.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/macro.h>
-
-.globl lowlevel_init
-lowlevel_init:
- /* Also setup the Peripheral Port Remap register inside the core */
- ldr r0, =ARM_PPMRR /* start from AIPS 2GB region */
- mcr p15, 0, r0, c15, c2, 4
-
- write32 IPU_CONF, IPU_CONF_DI_EN
- write32 CCM_CCMR, CCM_CCMR_SETUP
-
- wait_timer 0x40000
-
- write32 CCM_CCMR, CCM_CCMR_SETUP | CCMR_MPE
- write32 CCM_CCMR, (CCM_CCMR_SETUP | CCMR_MPE) & ~CCMR_MDS
-
- /* Set up clock to 532MHz */
- write32 CCM_PDR0, CCM_PDR0_SETUP_532MHZ
- write32 CCM_MPCTL, CCM_MPCTL_SETUP_532MHZ
-
- write32 CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1)
-
- /* Set up MX31 DDR pins */
- write32 IOMUXC_SW_PAD_CTL_SDCKE1_SDCLK_SDCLK_B, 0
- write32 IOMUXC_SW_PAD_CTL_CAS_SDWE_SDCKE0, 0
- write32 IOMUXC_SW_PAD_CTL_BCLK_RW_RAS, 0
- write32 IOMUXC_SW_PAD_CTL_CS2_CS3_CS4, 0x1000
- write32 IOMUXC_SW_PAD_CTL_DQM3_EB0_EB1, 0
- write32 IOMUXC_SW_PAD_CTL_DQM0_DQM1_DQM2, 0
- write32 IOMUXC_SW_PAD_CTL_SD29_SD30_SD31, 0
- write32 IOMUXC_SW_PAD_CTL_SD26_SD27_SD28, 0
- write32 IOMUXC_SW_PAD_CTL_SD23_SD24_SD25, 0
- write32 IOMUXC_SW_PAD_CTL_SD20_SD21_SD22, 0
- write32 IOMUXC_SW_PAD_CTL_SD17_SD18_SD19, 0
- write32 IOMUXC_SW_PAD_CTL_SD14_SD15_SD16, 0
- write32 IOMUXC_SW_PAD_CTL_SD11_SD12_SD13, 0
- write32 IOMUXC_SW_PAD_CTL_SD8_SD9_SD10, 0
- write32 IOMUXC_SW_PAD_CTL_SD5_SD6_SD7, 0
- write32 IOMUXC_SW_PAD_CTL_SD2_SD3_SD4, 0
- write32 IOMUXC_SW_PAD_CTL_SDBA0_SD0_SD1, 0
- write32 IOMUXC_SW_PAD_CTL_A24_A25_SDBA1, 0
- write32 IOMUXC_SW_PAD_CTL_A21_A22_A23, 0
- write32 IOMUXC_SW_PAD_CTL_A18_A19_A20, 0
- write32 IOMUXC_SW_PAD_CTL_A15_A16_A17, 0
- write32 IOMUXC_SW_PAD_CTL_A12_A13_A14, 0
- write32 IOMUXC_SW_PAD_CTL_A10_MA10_A11, 0
- write32 IOMUXC_SW_PAD_CTL_A7_A8_A9, 0
- write32 IOMUXC_SW_PAD_CTL_A4_A5_A6, 0
- write32 IOMUXC_SW_PAD_CTL_A1_A2_A3, 0
- write32 IOMUXC_SW_PAD_CTL_VPG0_VPG1_A0, 0
-
- /* Set up MX31 DDR Memory Controller */
- write32 WEIM_ESDMISC, ESDMISC_MDDR_SETUP
- write32 WEIM_ESDCFG0, ESDCFG0_MDDR_SETUP
-
- /* Perform DDR init sequence */
- write32 WEIM_ESDCTL0, ESDCTL_PRECHARGE
- write32 CSD0_BASE | 0x0f00, 0x12344321
- write32 WEIM_ESDCTL0, ESDCTL_AUTOREFRESH
- write32 CSD0_BASE, 0x12344321
- write32 CSD0_BASE, 0x12344321
- write32 WEIM_ESDCTL0, ESDCTL_LOADMODEREG
- write8 CSD0_BASE | 0x00000033, 0xda
- write8 CSD0_BASE | 0x01000000, 0xff
- write32 WEIM_ESDCTL0, ESDCTL_RW
- write32 CSD0_BASE, 0xDEADBEEF
- write32 WEIM_ESDMISC, ESDMISC_MDDR_RESET_DL
-
- mov pc, lr
diff --git a/board/freescale/mx31pdk/mx31pdk.c b/board/freescale/mx31pdk/mx31pdk.c
deleted file mode 100644
index 06fe51db71..0000000000
--- a/board/freescale/mx31pdk/mx31pdk.c
+++ /dev/null
@@ -1,119 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- *
- * (C) Copyright 2009 Magnus Lilja <lilja.magnus at gmail.com>
- *
- * (c) 2007 Pengutronix, Sascha Hauer <s.hauer at pengutronix.de>
- */
-
-
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-#include <watchdog.h>
-#include <power/pmic.h>
-#include <fsl_pmic.h>
-#include <errno.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_SPL_BUILD
-void board_init_f(ulong bootflag)
-{
- /*
- * copy ourselves from where we are running to where we were
- * linked at. Use ulong pointers as all addresses involved
- * are 4-byte-aligned.
- */
- ulong *start_ptr, *end_ptr, *link_ptr, *run_ptr, *dst;
- asm volatile ("ldr %0, =_start" : "=r"(start_ptr));
- asm volatile ("ldr %0, =_end" : "=r"(end_ptr));
- asm volatile ("ldr %0, =board_init_f" : "=r"(link_ptr));
- asm volatile ("adr %0, board_init_f" : "=r"(run_ptr));
- for (dst = start_ptr; dst < end_ptr; dst++)
- *dst = *(dst+(run_ptr-link_ptr));
- /*
- * branch to nand_boot's link-time address.
- */
- asm volatile("ldr pc, =nand_boot");
-}
-#endif
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
- PHYS_SDRAM_1_SIZE);
- return 0;
-}
-
-int board_early_init_f(void)
-{
- /* CS5: CPLD incl. network controller */
- static const struct mxc_weimcs cs5 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 3, 24, 0, 4, 3),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(2, 2, 2, 5, 2, 0, 5, 2, 0, 0, 0, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(2, 2, 2, 2, 0, 0, 2, 2, 0, 0, 0, 0, 0, 0)
- };
-
- mxc_setup_weimcs(5, &cs5);
-
- /* Setup UART1 and SPI2 pins */
- mx31_uart1_hw_init();
- mx31_spi2_hw_init();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* adress of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- return 0;
-}
-
-int board_late_init(void)
-{
- u32 val;
- struct pmic *p;
- int ret;
-
- ret = pmic_init(CONFIG_FSL_PMIC_BUS);
- if (ret)
- return ret;
-
- p = pmic_get("FSL_PMIC");
- if (!p)
- return -ENODEV;
- /* Enable RTC battery */
- pmic_reg_read(p, REG_POWER_CTL0, &val);
- pmic_reg_write(p, REG_POWER_CTL0, val | COINCHEN);
- pmic_reg_write(p, REG_INT_STATUS1, RTCRSTI);
-#ifdef CONFIG_HW_WATCHDOG
- hw_watchdog_init();
-#endif
- return 0;
-}
-
-int checkboard(void)
-{
- printf("Board: MX31PDK\n");
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC911X
- rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
-#endif
- return rc;
-}
diff --git a/configs/mx31pdk_defconfig b/configs/mx31pdk_defconfig
deleted file mode 100644
index c53c23a363..0000000000
--- a/configs/mx31pdk_defconfig
+++ /dev/null
@@ -1,40 +0,0 @@
-CONFIG_ARM=y
-# CONFIG_SPL_USE_ARCH_MEMCPY is not set
-# CONFIG_SPL_USE_ARCH_MEMSET is not set
-CONFIG_ARCH_MX31=y
-CONFIG_SPL_LDSCRIPT="arch/arm/cpu/u-boot-spl.lds"
-CONFIG_SYS_TEXT_BASE=0x87e00000
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x40000
-CONFIG_TARGET_MX31PDK=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x60000
-CONFIG_SPL_TEXT_BASE=0x87dc0000
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_SPL_NAND_SUPPORT=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_SPI=y
-CONFIG_DEFAULT_SPI_BUS=1
-CONFIG_DEFAULT_SPI_MODE=4
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_MXC_GPIO=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXC=y
-CONFIG_SMC911X=y
-CONFIG_SMC911X_BASE=0xB6000000
-CONFIG_SMC911X_32_BIT=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
diff --git a/include/configs/mx31pdk.h b/include/configs/mx31pdk.h
deleted file mode 100644
index f910d6199b..0000000000
--- a/include/configs/mx31pdk.h
+++ /dev/null
@@ -1,141 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2008 Magnus Lilja <lilja.magnus at gmail.com>
- *
- * (C) Copyright 2004
- * Texas Instruments.
- * Richard Woodruff <r-woodruff2 at ti.com>
- * Kshitij Gupta <kshitij at ti.com>
- *
- * Configuration settings for the Freescale i.MX31 PDK board.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
-/* High Level Configuration Options */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_MACH_TYPE MACH_TYPE_MX31_3DS
-
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SPL_MAX_SIZE 2048
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (2*CONFIG_ENV_SIZE + 2 * 128 * 1024)
-
-/*
- * Hardware drivers
- */
-
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-/* PMIC Controller */
-#define CONFIG_POWER
-#define CONFIG_POWER_SPI
-#define CONFIG_POWER_FSL
-#define CONFIG_FSL_PMIC_BUS 1
-#define CONFIG_FSL_PMIC_CS 2
-#define CONFIG_FSL_PMIC_CLK 1000000
-#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_FSL_PMIC_BITLEN 32
-#define CONFIG_RTC_MC13XXX
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
- "bootargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs " \
- "ip=dhcp nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \
- "bootcmd=run bootcmd_net\0" \
- "bootcmd_net=run bootargs_base bootargs_mtd bootargs_nfs; " \
- "tftpboot 0x81000000 uImage-mx31; bootm\0" \
- "prg_uboot=tftpboot 0x81000000 u-boot-with-spl.bin; " \
- "nand erase 0x0 0x40000; " \
- "nand write 0x81000000 0x0 0x40000\0"
-
-/*
- * Miscellaneous configurable options
- */
-
-/* memtest works on */
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR 0x81000000
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define PHYS_SDRAM_1 CSD0_BASE
-#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE)
-
-/*
- * environment organization
- */
-
-/*
- * NAND driver
- */
-#define CONFIG_MXC_NAND_REGS_BASE NFC_BASE_ADDR
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR
-#define CONFIG_MXC_NAND_HWECC
-#define CONFIG_SYS_NAND_LARGEPAGE
-
-/* NAND configuration for the NAND_SPL */
-
-/* Start copying real U-Boot from the second page */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SPL_PAD_TO
-#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x3f800
-/* Load U-Boot to this address */
-#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
-
-#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_SIZE (256 * 1024 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
-
-/* Configuration of lowlevel_init.S (clocks and SDRAM) */
-#define CCM_CCMR_SETUP 0x074B0BF5
-#define CCM_PDR0_SETUP_532MHZ (PDR0_CSI_PODF(0x3f) | PDR0_CSI_PRDF(7) | \
- PDR0_PER_PODF(7) | PDR0_HSP_PODF(3) | \
- PDR0_NFC_PODF(5) | PDR0_IPG_PODF(1) | \
- PDR0_MAX_PODF(3) | PDR0_MCU_PODF(0))
-#define CCM_MPCTL_SETUP_532MHZ (PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | \
- PLL_MFN(12))
-
-#define ESDMISC_MDDR_SETUP 0x00000004
-#define ESDMISC_MDDR_RESET_DL 0x0000000c
-#define ESDCFG0_MDDR_SETUP 0x006ac73a
-
-#define ESDCTL_ROW_COL (ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
-#define ESDCTL_SETTINGS (ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
- ESDCTL_DSIZ(2) | ESDCTL_BL(1))
-#define ESDCTL_PRECHARGE (ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
-#define ESDCTL_AUTOREFRESH (ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
-#define ESDCTL_LOADMODEREG (ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
-#define ESDCTL_RW ESDCTL_SETTINGS
-
-#endif /* __CONFIG_H */
--
2.25.1
More information about the U-Boot
mailing list