[EXT] [PATCH 1/1] power: pmic_pca9450: fix PCA9450A I2C address

[Ye Li]

On Mon, 2020-06-29 at 12:11 +0200, Sébastien Szymanski wrote:
> Caution: EXT Email
> 
> On 6/29/20 11:51 AM, Ye Li wrote:
> > 
> > On Mon, 2020-06-29 at 10:42 +0200, Sébastien Szymanski wrote:
> > > 
> > > Caution: EXT Email
> > > 
> > > PCA9450A I2C address is 0x25. Fix it.
> > > 
> > > Signed-off-by: Sébastien Szymanski <sebastien.szymanski at armadeus.
> > > com>
> > > ---
> > >  drivers/power/pmic/pmic_pca9450.c | 2 +-
> > >  1 file changed, 1 insertion(+), 1 deletion(-)
> > > 
> > > diff --git a/drivers/power/pmic/pmic_pca9450.c
> > > b/drivers/power/pmic/pmic_pca9450.c
> > > index 67a9090200..c0fb78c4cd 100644
> > > --- a/drivers/power/pmic/pmic_pca9450.c
> > > +++ b/drivers/power/pmic/pmic_pca9450.c
> > > @@ -23,7 +23,7 @@ int power_pca9450a_init(unsigned char bus)
> > >         p->name = pca9450_name;
> > >         p->interface = PMIC_I2C;
> > >         p->number_of_regs = PCA9450_REG_NUM;
> > > -       p->hw.i2c.addr = 0x35;
> > > +       p->hw.i2c.addr = 0x25;
> > The address 0x35 is correct for PCA9540A. You are probably using
> > PCA9540B/C which address is 0x25. If so, please
> > call power_pca9450b_init.
> No.
> I am using a PCA9450A chip and its address is 0x25:
> 
> # i2cget -f -y 0 0x25 0x00
> 0x10
> 
> Moreover, the datasheet says it's 0x25. [1]
> 
> [1] https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2
> Fwww.nxp.com%2Fdocs%2Fen%2Fdata-
> sheet%2FPCA9450DS.pdf&data=02%7C01%7Cye.li%40nxp.com%7Cf58d2e0f30
> 7045ca2b7408d81c14d040%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C1%7C6
> 37290222999360806&sdata=cLYNDpYxwFaDrMSq%2B%2F2bivTXw9a8BAkUgTf3%
> 2B5mWcWg%3D&reserved=0
> 
> Regards,

Our doc shows the i2c address has a choice by MTP. 

The I2C address at Power-On Reset is as follows:
• Write address: 0x6A ( MTP Option : 4A )
• Read address: 0x6B ( MTP Option : 4B )


And we also has an 8MM board (not for customer) using PCA9450A with
0x35 address. 

Best regards,
Ye Li
> 
> > 
> > 
> > Best regards,
> > Ye Li
> > > 
> > >         p->hw.i2c.tx_num = 1;
> > >         p->bus = bus;
> > > 
> > > --
> > > 2.26.2
> 
> --
> Sébastien Szymanski, Armadeus Systems
> Software engineer