[PATCH] omap3_beagle: Finish current outstanding DM migrations

[Tom Rini]

At this point in time we can now remove our legacy code and switch to
enabling DM for USB and Ethernet.

Cc: Derald D. Woods <woods.technical at gmail.com>
Cc: Adam Ford <aford173 at gmail.com>
Signed-off-by: Tom Rini <trini at konsulko.com>
---
 board/ti/beagle/beagle.c       | 70 ----------------------------------
 configs/omap3_beagle_defconfig |  5 ++-
 2 files changed, 4 insertions(+), 71 deletions(-)

diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index 9139ad87d400..9ccd566da370 100644
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -40,11 +40,6 @@
 #include "beagle.h"
 #include <command.h>
 
-#ifdef CONFIG_USB_EHCI_HCD
-#include <usb.h>
-#include <asm/ehci-omap.h>
-#endif
-
 #define TWL4030_I2C_BUS			0
 #define EXPANSION_EEPROM_I2C_BUS	1
 #define EXPANSION_EEPROM_I2C_ADDRESS	0x50
@@ -297,33 +292,6 @@ static void beagle_dvi_pup(void)
 }
 #endif
 
-#ifdef CONFIG_USB_MUSB_OMAP2PLUS
-static struct musb_hdrc_config musb_config = {
-	.multipoint     = 1,
-	.dyn_fifo       = 1,
-	.num_eps        = 16,
-	.ram_bits       = 12,
-};
-
-static struct omap_musb_board_data musb_board_data = {
-	.interface_type	= MUSB_INTERFACE_ULPI,
-};
-
-static struct musb_hdrc_platform_data musb_plat = {
-#if defined(CONFIG_USB_MUSB_HOST)
-	.mode           = MUSB_HOST,
-#elif defined(CONFIG_USB_MUSB_GADGET)
-	.mode		= MUSB_PERIPHERAL,
-#else
-#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET"
-#endif
-	.config         = &musb_config,
-	.power          = 100,
-	.platform_ops	= &omap2430_ops,
-	.board_data	= &musb_board_data,
-};
-#endif
-
 /*
  * Routine: misc_init_r
  * Description: Configure board specific parts
@@ -506,10 +474,6 @@ int misc_init_r(void)
 	omap3_dss_enable();
 #endif
 
-#ifdef CONFIG_USB_MUSB_OMAP2PLUS
-	musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
-#endif
-
 	if (generate_fake_mac)
 		omap_die_id_usbethaddr();
 
@@ -548,37 +512,3 @@ void board_mmc_power_init(void)
 	twl4030_power_mmc_init(0);
 }
 #endif
-
-#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
-/* Call usb_stop() before starting the kernel */
-void show_boot_progress(int val)
-{
-	if (val == BOOTSTAGE_ID_RUN_OS)
-		usb_stop();
-}
-
-static struct omap_usbhs_board_data usbhs_bdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
-};
-
-int ehci_hcd_init(int index, enum usb_init_type init,
-		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
-{
-	return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
-}
-
-int ehci_hcd_stop(int index)
-{
-	return omap_ehci_hcd_stop();
-}
-
-#endif /* CONFIG_USB_EHCI_HCD */
-
-#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
-int board_eth_init(bd_t *bis)
-{
-	return usb_eth_initialize(bis);
-}
-#endif
diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig
index ed7cb8f2ff63..b08ffc062d29 100644
--- a/configs/omap3_beagle_defconfig
+++ b/configs/omap3_beagle_defconfig
@@ -3,11 +3,11 @@ CONFIG_ARM=y
 # CONFIG_SPL_USE_ARCH_MEMSET is not set
 CONFIG_ARCH_OMAP2PLUS=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_SPL_TEXT_BASE=0x40200000
 CONFIG_TARGET_OMAP3_BEAGLE=y
 CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
 CONFIG_NR_DRAM_BANKS=2
 CONFIG_SPL=y
-CONFIG_SPL_TEXT_BASE=0x40200000
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
 CONFIG_USE_PREBOOT=y
@@ -73,10 +73,13 @@ CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
 CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
 CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
 CONFIG_SPL_NAND_SIMPLE=y
+CONFIG_DM_ETH=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_OMAP3_SPI=y
 CONFIG_USB=y
+CONFIG_DM_USB=y
+# CONFIG_SPL_DM_USB is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OMAP3=y
 CONFIG_USB_MUSB_GADGET=y
-- 
2.17.1