[PATCH v5 00/12] ClearFog Base static variant support

[Stefan Roese]

Hi Joel,

On 22.03.20 19:46, Joel Johnson wrote:
> I just wanted to ping on this review 
> (http://patchwork.ozlabs.org/project/uboot/list/?series=155533) to see 
> if it had reached an agreeable state or if there were still lingering 
> issues. I've been using it without issue against RC releases.
> 
> If the plan is to not include it in v2020.04 that's completely 
> reasonable, but I would request review and feedback on blocking issues, 
> otherwise does it have general agreement for merging in the next merge 
> window?

I won't pull this into v2020.04 as you might understand. I was hoping to
get some reviews and testing from people with access to those boards.

Baruch, could you please check again, if you agree with this approach?
Or do you have some change request for this build-time vs run-time
detection?

Thanks,
Stefan

> Thanks,
> Joel
> 
> On 2020-01-27 13:01, Joel Johnson wrote:
>> This patch series adds support for ClearFog Base static configuration,
>> as well as updating and fixing the ClearFog support for MMC and SPI
>> booting.
>>
>> v2 changes:
>>   - updated against, and dependent on,
>> https://patchwork.ozlabs.org/cover/1200324
>> v3 changes:
>>   - rebased against ClearFog runtime TLV EEPROM changes merged into 
>> mvebu/master
>> v4
>>   - adjust static SerDes configuration at runtime instead of #ifdef
>> v5
>>   - distinguish build-only config changes (SFP and PCIe/SATA) from
>>     runtime detectable config changes
>>   - retested SATA mode in PCIe slot with swap rx changes, confirmed
>>     working as presently patched. Only tested with ClearFog Base which
>>     only provides single channel, but Pro mechanism is parallel.
>>
>>
>> Joel Johnson (12):
>>   arm: mvebu: fix SerDes table alignment
>>   arm: mvebu: solidrun: remove hardcoded DTS MAC address
>>   arm: mvebu: clearfog: use Pro name by default
>>   arm: mvebu: clearfog: initial ClearFog Base variant
>>   arm: mvebu: clearfog: Add option for 2.5 Gbps SFP
>>   arm: mvebu: clearfog: Add SATA mode flags
>>   arm: mvebu: clearfog: Unify DT selection paths
>>   arm: mvebu: clearfog: add SPI offsets
>>   arm: mvebu: enable working default boot support
>>   arm: mvebu: clearfog: move ENV params to Kconfig
>>   arm: mvebu: clearfog: don't always use SPL MMC
>>   arm: mvebu: clearfog: Use Pro DT by default
>>
>>  .../arm/dts/armada-38x-solidrun-microsom.dtsi |  1 -
>>  arch/arm/mach-mvebu/Kconfig                   | 13 ++++
>>  .../serdes/a38x/high_speed_env_spec.c         |  6 +-
>>  board/solidrun/clearfog/Kconfig               | 62 +++++++++++++++++++
>>  board/solidrun/clearfog/clearfog.c            | 53 +++++++++++++---
>>  configs/clearfog_defconfig                    |  4 --
>>  include/configs/clearfog.h                    |  1 -
>>  7 files changed, 124 insertions(+), 16 deletions(-)
>>  create mode 100644 board/solidrun/clearfog/Kconfig


Viele Grüße,
Stefan

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de