[PATCH v5 00/12] ClearFog Base static variant support

[Baruch Siach]

Hi Stefan,

On Mon, Mar 23 2020, Stefan Roese wrote:
> On 22.03.20 19:46, Joel Johnson wrote:
>> I just wanted to ping on this review
>> (http://patchwork.ozlabs.org/project/uboot/list/?series=155533) to see if it
>> had reached an agreeable state or if there were still lingering issues. I've
>> been using it without issue against RC releases.
>>
>> If the plan is to not include it in v2020.04 that's completely reasonable,
>> but I would request review and feedback on blocking issues, otherwise does
>> it have general agreement for merging in the next merge window?
>
> I won't pull this into v2020.04 as you might understand. I was hoping to
> get some reviews and testing from people with access to those boards.
>
> Baruch, could you please check again, if you agree with this approach?
> Or do you have some change request for this build-time vs run-time
> detection?

This series is the end result of discussions between Joel and me on the
list with a few iterations. I am fine with this result, and I think it
is good to go. I can't test these patches at the moment. Hope to do that
some time later.

Thanks,
baruch

>> On 2020-01-27 13:01, Joel Johnson wrote:
>>> This patch series adds support for ClearFog Base static configuration,
>>> as well as updating and fixing the ClearFog support for MMC and SPI
>>> booting.
>>>
>>> v2 changes:
>>>   - updated against, and dependent on,
>>> https://patchwork.ozlabs.org/cover/1200324
>>> v3 changes:
>>>   - rebased against ClearFog runtime TLV EEPROM changes merged into
>>> mvebu/master
>>> v4
>>>   - adjust static SerDes configuration at runtime instead of #ifdef
>>> v5
>>>   - distinguish build-only config changes (SFP and PCIe/SATA) from
>>>     runtime detectable config changes
>>>   - retested SATA mode in PCIe slot with swap rx changes, confirmed
>>>     working as presently patched. Only tested with ClearFog Base which
>>>     only provides single channel, but Pro mechanism is parallel.
>>>
>>>
>>> Joel Johnson (12):
>>>   arm: mvebu: fix SerDes table alignment
>>>   arm: mvebu: solidrun: remove hardcoded DTS MAC address
>>>   arm: mvebu: clearfog: use Pro name by default
>>>   arm: mvebu: clearfog: initial ClearFog Base variant
>>>   arm: mvebu: clearfog: Add option for 2.5 Gbps SFP
>>>   arm: mvebu: clearfog: Add SATA mode flags
>>>   arm: mvebu: clearfog: Unify DT selection paths
>>>   arm: mvebu: clearfog: add SPI offsets
>>>   arm: mvebu: enable working default boot support
>>>   arm: mvebu: clearfog: move ENV params to Kconfig
>>>   arm: mvebu: clearfog: don't always use SPL MMC
>>>   arm: mvebu: clearfog: Use Pro DT by default
>>>
>>>  .../arm/dts/armada-38x-solidrun-microsom.dtsi |  1 -
>>>  arch/arm/mach-mvebu/Kconfig                   | 13 ++++
>>>  .../serdes/a38x/high_speed_env_spec.c         |  6 +-
>>>  board/solidrun/clearfog/Kconfig               | 62 +++++++++++++++++++
>>>  board/solidrun/clearfog/clearfog.c            | 53 +++++++++++++---
>>>  configs/clearfog_defconfig                    |  4 --
>>>  include/configs/clearfog.h                    |  1 -
>>>  7 files changed, 124 insertions(+), 16 deletions(-)
>>>  create mode 100644 board/solidrun/clearfog/Kconfig
>
>
> Viele Grüße,
> Stefan


--
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -