[PATCH v2] board:pm9261 - Enable DM_ETH
Ilko Iliev
iliev at ronetix.at
Mon Apr 19 15:37:33 CEST 2021
This patch remove the network support for PM9261 because
currently there is no DM suport for Davicom D9000.
Signed-off-by: Ilko Iliev <iliev at ronetix.at>
---
Changes for v2:
- add Signed-off-by
board/ronetix/pm9261/pm9261.c | 54 -----------------------------------
configs/pm9261_defconfig | 1 +
include/configs/pm9261.h | 9 ------
3 files changed, 1 insertion(+), 63 deletions(-)
diff --git a/board/ronetix/pm9261/pm9261.c b/board/ronetix/pm9261/pm9261.c
index 5be2c5e192..fe52c7c176 100644
--- a/board/ronetix/pm9261/pm9261.c
+++ b/board/ronetix/pm9261/pm9261.c
@@ -20,10 +20,6 @@
#include <asm/arch/at91_matrix.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
-#include <net.h>
-#endif
-#include <netdev.h>
#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -80,36 +76,6 @@ static void pm9261_nand_hw_init(void)
}
#endif
-
-#ifdef CONFIG_DRIVER_DM9000
-static void pm9261_dm9000_hw_init(void)
-{
- struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
-
- /* Configure SMC CS2 for DM9000 */
- writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
- AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
- &smc->cs[2].setup);
-
- writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
- AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
- &smc->cs[2].pulse);
-
- writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
- &smc->cs[2].cycle);
-
- writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
- AT91_SMC_MODE_EXNW_DISABLE |
- AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
- AT91_SMC_MODE_TDF_CYCLE(1),
- &smc->cs[2].mode);
-
- /* Configure Interrupt pin as input, no pull-up */
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_set_pio_input(AT91_PIO_PORTA, 24, 0);
-}
-#endif
-
int board_early_init_f(void)
{
return 0;
@@ -132,13 +98,6 @@ int board_init(void)
return 0;
}
-#ifdef CONFIG_DRIVER_DM9000
-int board_eth_init(struct bd_info *bis)
-{
- return dm9000_initialize(bis);
-}
-#endif
-
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
@@ -155,19 +114,6 @@ int dram_init_banksize(void)
return 0;
}
-#ifdef CONFIG_RESET_PHY_R
-void reset_phy(void)
-{
-#ifdef CONFIG_DRIVER_DM9000
- /*
- * Initialize ethernet HW addr prior to starting Linux,
- * needed for nfsroot
- */
- eth_init();
-#endif
-}
-#endif
-
#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard (void)
{
diff --git a/configs/pm9261_defconfig b/configs/pm9261_defconfig
index e0a2ae18c6..774039e8bc 100644
--- a/configs/pm9261_defconfig
+++ b/configs/pm9261_defconfig
@@ -50,6 +50,7 @@ CONFIG_NAND_ATMEL=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_DATAFLASH=y
+CONFIG_DM_ETH=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h
index 2cc47d1237..382d19a241 100644
--- a/include/configs/pm9261.h
+++ b/include/configs/pm9261.h
@@ -173,15 +173,6 @@
#define CONFIG_SYS_MAX_FLASH_SECT 256
#define CONFIG_SYS_MAX_FLASH_BANKS 1
-/* Ethernet */
-#define CONFIG_DRIVER_DM9000 1
-#define CONFIG_DM9000_BASE 0x30000000
-#define DM9000_IO CONFIG_DM9000_BASE
-#define DM9000_DATA (CONFIG_DM9000_BASE + 4)
-#define CONFIG_DM9000_USE_16BIT 1
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_RESET_PHY_R 1
-
/* USB */
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
--
2.25.1
More information about the U-Boot
mailing list