[PATCH v2] board:pm9261 - Enable DM_ETH

Eugen.Hristev at microchip.com Eugen.Hristev at microchip.com
Wed Apr 21 08:50:55 CEST 2021


On 4/19/21 4:37 PM, Ilko Iliev wrote:
> This patch remove the network support for PM9261 because
> currently there is no DM suport for Davicom D9000.
> 
> Signed-off-by: Ilko Iliev <iliev at ronetix.at>
> ---

Hi,

If I look at the commit message, I would expect something is enabled, 
but in fact something is removed.
Could you update the short commit subject according to what you are 
doing in the commit itself ?

Also, if you are removing the dm9000, why do you still enable the DM_ETH 
? what is it used for ?

Eugen

> Changes for v2:
>   - add Signed-off-by
> 
>   board/ronetix/pm9261/pm9261.c | 54 -----------------------------------
>   configs/pm9261_defconfig      |  1 +
>   include/configs/pm9261.h      |  9 ------
>   3 files changed, 1 insertion(+), 63 deletions(-)
> 
> diff --git a/board/ronetix/pm9261/pm9261.c b/board/ronetix/pm9261/pm9261.c
> index 5be2c5e192..fe52c7c176 100644
> --- a/board/ronetix/pm9261/pm9261.c
> +++ b/board/ronetix/pm9261/pm9261.c
> @@ -20,10 +20,6 @@
>   #include <asm/arch/at91_matrix.h>
>   #include <asm/arch/clk.h>
>   #include <asm/arch/gpio.h>
> -#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
> -#include <net.h>
> -#endif
> -#include <netdev.h>
>   #include <asm/mach-types.h>
> 
>   DECLARE_GLOBAL_DATA_PTR;
> @@ -80,36 +76,6 @@ static void pm9261_nand_hw_init(void)
>   }
>   #endif
> 
> -
> -#ifdef CONFIG_DRIVER_DM9000
> -static void pm9261_dm9000_hw_init(void)
> -{
> -       struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
> -
> -       /* Configure SMC CS2 for DM9000 */
> -       writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
> -               AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
> -               &smc->cs[2].setup);
> -
> -       writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
> -               AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
> -               &smc->cs[2].pulse);
> -
> -       writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
> -               &smc->cs[2].cycle);
> -
> -       writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
> -               AT91_SMC_MODE_EXNW_DISABLE |
> -               AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
> -               AT91_SMC_MODE_TDF_CYCLE(1),
> -               &smc->cs[2].mode);
> -
> -       /* Configure Interrupt pin as input, no pull-up */
> -       at91_periph_clk_enable(ATMEL_ID_PIOA);
> -       at91_set_pio_input(AT91_PIO_PORTA, 24, 0);
> -}
> -#endif
> -
>   int board_early_init_f(void)
>   {
>          return 0;
> @@ -132,13 +98,6 @@ int board_init(void)
>          return 0;
>   }
> 
> -#ifdef CONFIG_DRIVER_DM9000
> -int board_eth_init(struct bd_info *bis)
> -{
> -       return dm9000_initialize(bis);
> -}
> -#endif
> -
>   int dram_init(void)
>   {
>          /* dram_init must store complete ramsize in gd->ram_size */
> @@ -155,19 +114,6 @@ int dram_init_banksize(void)
>          return 0;
>   }
> 
> -#ifdef CONFIG_RESET_PHY_R
> -void reset_phy(void)
> -{
> -#ifdef CONFIG_DRIVER_DM9000
> -       /*
> -        * Initialize ethernet HW addr prior to starting Linux,
> -        * needed for nfsroot
> -        */
> -       eth_init();
> -#endif
> -}
> -#endif
> -
>   #ifdef CONFIG_DISPLAY_BOARDINFO
>   int checkboard (void)
>   {
> diff --git a/configs/pm9261_defconfig b/configs/pm9261_defconfig
> index e0a2ae18c6..774039e8bc 100644
> --- a/configs/pm9261_defconfig
> +++ b/configs/pm9261_defconfig
> @@ -50,6 +50,7 @@ CONFIG_NAND_ATMEL=y
>   CONFIG_DM_SPI_FLASH=y
>   CONFIG_SPI_FLASH_ATMEL=y
>   CONFIG_SPI_FLASH_DATAFLASH=y
> +CONFIG_DM_ETH=y
>   CONFIG_PINCTRL=y
>   CONFIG_PINCTRL_AT91=y
>   CONFIG_DM_SERIAL=y
> diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h
> index 2cc47d1237..382d19a241 100644
> --- a/include/configs/pm9261.h
> +++ b/include/configs/pm9261.h
> @@ -173,15 +173,6 @@
>   #define CONFIG_SYS_MAX_FLASH_SECT              256
>   #define CONFIG_SYS_MAX_FLASH_BANKS             1
> 
> -/* Ethernet */
> -#define CONFIG_DRIVER_DM9000                   1
> -#define CONFIG_DM9000_BASE                     0x30000000
> -#define DM9000_IO                              CONFIG_DM9000_BASE
> -#define DM9000_DATA                            (CONFIG_DM9000_BASE + 4)
> -#define CONFIG_DM9000_USE_16BIT                        1
> -#define CONFIG_NET_RETRY_COUNT                 20
> -#define CONFIG_RESET_PHY_R                     1
> -
>   /* USB */
>   #define CONFIG_USB_ATMEL
>   #define CONFIG_USB_ATMEL_CLK_SEL_PLLB
> --
> 2.25.1
> 



More information about the U-Boot mailing list