[PATCH v2] board:pm9261 - Enable DM_ETH

Ilko Iliev iliev at ronetix.at
Fri Apr 23 11:19:03 CEST 2021



On 21.04.21 08:50, Eugen.Hristev at microchip.com wrote:
> On 4/19/21 4:37 PM, Ilko Iliev wrote:
>> This patch remove the network support for PM9261 because
>> currently there is no DM suport for Davicom D9000.
>>
>> Signed-off-by: Ilko Iliev <iliev at ronetix.at>
>> ---
> Hi,
>
> If I look at the commit message, I would expect something is enabled,
> but in fact something is removed.
> Could you update the short commit subject according to what you are
> doing in the commit itself ?
>
> Also, if you are removing the dm9000, why do you still enable the DM_ETH
> ? what is it used for ?
>
> Eugen

Hi,
The DM9000 is removed because there is no DM support.
DM_ETH is enabled, because of the warning that the board will be removed
without DM_ETH.
Is there a way to build U-BOOT without ETH support and without the 
warning for
missing DM_ETH?

Regards,
Ilko ILEV

>> Changes for v2:
>>    - add Signed-off-by
>>
>>    board/ronetix/pm9261/pm9261.c | 54 -----------------------------------
>>    configs/pm9261_defconfig      |  1 +
>>    include/configs/pm9261.h      |  9 ------
>>    3 files changed, 1 insertion(+), 63 deletions(-)
>>
>> diff --git a/board/ronetix/pm9261/pm9261.c b/board/ronetix/pm9261/pm9261.c
>> index 5be2c5e192..fe52c7c176 100644
>> --- a/board/ronetix/pm9261/pm9261.c
>> +++ b/board/ronetix/pm9261/pm9261.c
>> @@ -20,10 +20,6 @@
>>    #include <asm/arch/at91_matrix.h>
>>    #include <asm/arch/clk.h>
>>    #include <asm/arch/gpio.h>
>> -#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
>> -#include <net.h>
>> -#endif
>> -#include <netdev.h>
>>    #include <asm/mach-types.h>
>>
>>    DECLARE_GLOBAL_DATA_PTR;
>> @@ -80,36 +76,6 @@ static void pm9261_nand_hw_init(void)
>>    }
>>    #endif
>>
>> -
>> -#ifdef CONFIG_DRIVER_DM9000
>> -static void pm9261_dm9000_hw_init(void)
>> -{
>> -       struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
>> -
>> -       /* Configure SMC CS2 for DM9000 */
>> -       writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
>> -               AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
>> -               &smc->cs[2].setup);
>> -
>> -       writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
>> -               AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
>> -               &smc->cs[2].pulse);
>> -
>> -       writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
>> -               &smc->cs[2].cycle);
>> -
>> -       writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
>> -               AT91_SMC_MODE_EXNW_DISABLE |
>> -               AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
>> -               AT91_SMC_MODE_TDF_CYCLE(1),
>> -               &smc->cs[2].mode);
>> -
>> -       /* Configure Interrupt pin as input, no pull-up */
>> -       at91_periph_clk_enable(ATMEL_ID_PIOA);
>> -       at91_set_pio_input(AT91_PIO_PORTA, 24, 0);
>> -}
>> -#endif
>> -
>>    int board_early_init_f(void)
>>    {
>>           return 0;
>> @@ -132,13 +98,6 @@ int board_init(void)
>>           return 0;
>>    }
>>
>> -#ifdef CONFIG_DRIVER_DM9000
>> -int board_eth_init(struct bd_info *bis)
>> -{
>> -       return dm9000_initialize(bis);
>> -}
>> -#endif
>> -
>>    int dram_init(void)
>>    {
>>           /* dram_init must store complete ramsize in gd->ram_size */
>> @@ -155,19 +114,6 @@ int dram_init_banksize(void)
>>           return 0;
>>    }
>>
>> -#ifdef CONFIG_RESET_PHY_R
>> -void reset_phy(void)
>> -{
>> -#ifdef CONFIG_DRIVER_DM9000
>> -       /*
>> -        * Initialize ethernet HW addr prior to starting Linux,
>> -        * needed for nfsroot
>> -        */
>> -       eth_init();
>> -#endif
>> -}
>> -#endif
>> -
>>    #ifdef CONFIG_DISPLAY_BOARDINFO
>>    int checkboard (void)
>>    {
>> diff --git a/configs/pm9261_defconfig b/configs/pm9261_defconfig
>> index e0a2ae18c6..774039e8bc 100644
>> --- a/configs/pm9261_defconfig
>> +++ b/configs/pm9261_defconfig
>> @@ -50,6 +50,7 @@ CONFIG_NAND_ATMEL=y
>>    CONFIG_DM_SPI_FLASH=y
>>    CONFIG_SPI_FLASH_ATMEL=y
>>    CONFIG_SPI_FLASH_DATAFLASH=y
>> +CONFIG_DM_ETH=y
>>    CONFIG_PINCTRL=y
>>    CONFIG_PINCTRL_AT91=y
>>    CONFIG_DM_SERIAL=y
>> diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h
>> index 2cc47d1237..382d19a241 100644
>> --- a/include/configs/pm9261.h
>> +++ b/include/configs/pm9261.h
>> @@ -173,15 +173,6 @@
>>    #define CONFIG_SYS_MAX_FLASH_SECT              256
>>    #define CONFIG_SYS_MAX_FLASH_BANKS             1
>>
>> -/* Ethernet */
>> -#define CONFIG_DRIVER_DM9000                   1
>> -#define CONFIG_DM9000_BASE                     0x30000000
>> -#define DM9000_IO                              CONFIG_DM9000_BASE
>> -#define DM9000_DATA                            (CONFIG_DM9000_BASE + 4)
>> -#define CONFIG_DM9000_USE_16BIT                        1
>> -#define CONFIG_NET_RETRY_COUNT                 20
>> -#define CONFIG_RESET_PHY_R                     1
>> -
>>    /* USB */
>>    #define CONFIG_USB_ATMEL
>>    #define CONFIG_USB_ATMEL_CLK_SEL_PLLB
>> --
>> 2.25.1
>>

-- 
With best regards,
Ilko Iliev
Ronetix Development Tools GmbH
Hirschstettner Str. 19/Z110
1220 Vienna, Austria
Tel: +43 1 236 1101 - 10
E-Mail: iliev at ronetix.at
Web: www.ronetix.at



More information about the U-Boot mailing list