[PATCH v2] board:pm9261 - Enable DM_ETH

Eugen.Hristev at microchip.com Eugen.Hristev at microchip.com
Fri Apr 23 11:38:06 CEST 2021


On 4/23/21 12:19 PM, Ilko Iliev wrote:
> On 21.04.21 08:50, Eugen.Hristev at microchip.com wrote:
>> On 4/19/21 4:37 PM, Ilko Iliev wrote:
>>> This patch remove the network support for PM9261 because
>>> currently there is no DM suport for Davicom D9000.
>>>
>>> Signed-off-by: Ilko Iliev <iliev at ronetix.at>
>>> ---
>> Hi,
>>
>> If I look at the commit message, I would expect something is enabled,
>> but in fact something is removed.
>> Could you update the short commit subject according to what you are
>> doing in the commit itself ?
>>
>> Also, if you are removing the dm9000, why do you still enable the DM_ETH
>> ? what is it used for ?
>>
>> Eugen
> 
> Hi,
> The DM9000 is removed because there is no DM support.
> DM_ETH is enabled, because of the warning that the board will be removed
> without DM_ETH.
> Is there a way to build U-BOOT without ETH support and without the
> warning for
> missing DM_ETH?

Hi,

We should be able to have the board without ETH at all, probably 
something else causes the warning trigger. Something out of date may be 
detected that requires DM_ETH


I noticed this in Makefile

$(call deprecated,CONFIG_DM_ETH,Ethernet drivers,v2020.07,$(CONFIG_NET))

it is likely that you have to remove CONFIG_NET first, and then you 
won't be prompted to have DM_ETH set.

Could you look at this please ?

Thanks


> 
> Regards,
> Ilko ILEV
> 
>>> Changes for v2:
>>>    - add Signed-off-by
>>>
>>>    board/ronetix/pm9261/pm9261.c | 54 
>>> -----------------------------------
>>>    configs/pm9261_defconfig      |  1 +
>>>    include/configs/pm9261.h      |  9 ------
>>>    3 files changed, 1 insertion(+), 63 deletions(-)
>>>
>>> diff --git a/board/ronetix/pm9261/pm9261.c 
>>> b/board/ronetix/pm9261/pm9261.c
>>> index 5be2c5e192..fe52c7c176 100644
>>> --- a/board/ronetix/pm9261/pm9261.c
>>> +++ b/board/ronetix/pm9261/pm9261.c
>>> @@ -20,10 +20,6 @@
>>>    #include <asm/arch/at91_matrix.h>
>>>    #include <asm/arch/clk.h>
>>>    #include <asm/arch/gpio.h>
>>> -#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
>>> -#include <net.h>
>>> -#endif
>>> -#include <netdev.h>
>>>    #include <asm/mach-types.h>
>>>
>>>    DECLARE_GLOBAL_DATA_PTR;
>>> @@ -80,36 +76,6 @@ static void pm9261_nand_hw_init(void)
>>>    }
>>>    #endif
>>>
>>> -
>>> -#ifdef CONFIG_DRIVER_DM9000
>>> -static void pm9261_dm9000_hw_init(void)
>>> -{
>>> -       struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
>>> -
>>> -       /* Configure SMC CS2 for DM9000 */
>>> -       writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
>>> -               AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
>>> -               &smc->cs[2].setup);
>>> -
>>> -       writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
>>> -               AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
>>> -               &smc->cs[2].pulse);
>>> -
>>> -       writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
>>> -               &smc->cs[2].cycle);
>>> -
>>> -       writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
>>> -               AT91_SMC_MODE_EXNW_DISABLE |
>>> -               AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
>>> -               AT91_SMC_MODE_TDF_CYCLE(1),
>>> -               &smc->cs[2].mode);
>>> -
>>> -       /* Configure Interrupt pin as input, no pull-up */
>>> -       at91_periph_clk_enable(ATMEL_ID_PIOA);
>>> -       at91_set_pio_input(AT91_PIO_PORTA, 24, 0);
>>> -}
>>> -#endif
>>> -
>>>    int board_early_init_f(void)
>>>    {
>>>           return 0;
>>> @@ -132,13 +98,6 @@ int board_init(void)
>>>           return 0;
>>>    }
>>>
>>> -#ifdef CONFIG_DRIVER_DM9000
>>> -int board_eth_init(struct bd_info *bis)
>>> -{
>>> -       return dm9000_initialize(bis);
>>> -}
>>> -#endif
>>> -
>>>    int dram_init(void)
>>>    {
>>>           /* dram_init must store complete ramsize in gd->ram_size */
>>> @@ -155,19 +114,6 @@ int dram_init_banksize(void)
>>>           return 0;
>>>    }
>>>
>>> -#ifdef CONFIG_RESET_PHY_R
>>> -void reset_phy(void)
>>> -{
>>> -#ifdef CONFIG_DRIVER_DM9000
>>> -       /*
>>> -        * Initialize ethernet HW addr prior to starting Linux,
>>> -        * needed for nfsroot
>>> -        */
>>> -       eth_init();
>>> -#endif
>>> -}
>>> -#endif
>>> -
>>>    #ifdef CONFIG_DISPLAY_BOARDINFO
>>>    int checkboard (void)
>>>    {
>>> diff --git a/configs/pm9261_defconfig b/configs/pm9261_defconfig
>>> index e0a2ae18c6..774039e8bc 100644
>>> --- a/configs/pm9261_defconfig
>>> +++ b/configs/pm9261_defconfig
>>> @@ -50,6 +50,7 @@ CONFIG_NAND_ATMEL=y
>>>    CONFIG_DM_SPI_FLASH=y
>>>    CONFIG_SPI_FLASH_ATMEL=y
>>>    CONFIG_SPI_FLASH_DATAFLASH=y
>>> +CONFIG_DM_ETH=y
>>>    CONFIG_PINCTRL=y
>>>    CONFIG_PINCTRL_AT91=y
>>>    CONFIG_DM_SERIAL=y
>>> diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h
>>> index 2cc47d1237..382d19a241 100644
>>> --- a/include/configs/pm9261.h
>>> +++ b/include/configs/pm9261.h
>>> @@ -173,15 +173,6 @@
>>>    #define CONFIG_SYS_MAX_FLASH_SECT              256
>>>    #define CONFIG_SYS_MAX_FLASH_BANKS             1
>>>
>>> -/* Ethernet */
>>> -#define CONFIG_DRIVER_DM9000                   1
>>> -#define CONFIG_DM9000_BASE                     0x30000000
>>> -#define DM9000_IO                              CONFIG_DM9000_BASE
>>> -#define DM9000_DATA                            (CONFIG_DM9000_BASE + 4)
>>> -#define CONFIG_DM9000_USE_16BIT                        1
>>> -#define CONFIG_NET_RETRY_COUNT                 20
>>> -#define CONFIG_RESET_PHY_R                     1
>>> -
>>>    /* USB */
>>>    #define CONFIG_USB_ATMEL
>>>    #define CONFIG_USB_ATMEL_CLK_SEL_PLLB
>>> -- 
>>> 2.25.1
>>>
> 
> -- 
> With best regards,
> Ilko Iliev
> Ronetix Development Tools GmbH
> Hirschstettner Str. 19/Z110
> 1220 Vienna, Austria
> Tel: +43 1 236 1101 - 10
> E-Mail: iliev at ronetix.at
> Web: www.ronetix.at
> 



More information about the U-Boot mailing list