[EXT] Re: Problem on imx: add rom api support on imx8mn
Michael Nazzareno Trimarchi
michael at amarulasolutions.com
Thu Jul 15 10:19:14 CEST 2021
Hi
On Thu, Jul 15, 2021 at 9:56 AM Ye Li <ye.li at nxp.com> wrote:
>
> Hi Michael,
>
> > -----Original Message-----
> > From: Michael Nazzareno Trimarchi <michael at amarulasolutions.com>
> > Sent: Thursday, July 15, 2021 2:52 PM
> > To: Peng Fan (OSS) <peng.fan at oss.nxp.com>
> > Cc: Peng Fan <peng.fan at nxp.com>; U-Boot-Denx <u-boot at lists.denx.de>;
> > Stefano Babic <sbabic at denx.de>; Ye Li <ye.li at nxp.com>; Fabio Estevam
> > <festevam at gmail.com>; Jagan Teki <jagan at amarulasolutions.com>
> > Subject: [EXT] Re: Problem on imx: add rom api support on imx8mn
> >
> > Caution: EXT Email
> >
> > Hi
> >
> > On Thu, Jul 15, 2021 at 8:47 AM Peng Fan (OSS) <peng.fan at oss.nxp.com>
> > wrote:
> > >
> > >
> > >
> > > On 2021/7/8 17:15, Michael Nazzareno Trimarchi wrote:
> > > > Hi Peng
> > > >
> > > > On Thu, Jul 8, 2021 at 9:12 AM Peng Fan (OSS) <peng.fan at oss.nxp.com>
> > wrote:
> > > >>
> > > >> On 2021/7/4 1:24, Michael Nazzareno Trimarchi wrote:
> > > >>> Hi all
> > > >>>
> > > >>> I have some problems that I have understood and fixed but I can
> > > >>> not explain. Right now I have on imx8mn that can boot from boot0
> > > >>> or boot1 partition after remove a condition in the
> > > >>> is_boot_from_stream_device
> > > >>>
> > > >>> This is a boot from mmcblk0boot0 with some debug
> > > >>>
> > > >>> U-Boot SPL 2020.04-5.4.70-2.3.2+gf3bcbdfc62 (Jul 03 2021 -
> > > >>> 17:00:27 +0000) power_bd71837_init
> > > >>> DDRINFO: start DRAM init
> > > >>> DDRINFO: DRAM rate 1600MTS
> > > >>> DDRINFO:ddrphy calibration done
> > > >>> DDRINFO: ddrmix config done
> > > >>> Normal Boot
> > > >>> Trying to boot from BOOTROM
> > > >>> ROM API interface 2 from boot 131073
> > > >>>
> > > >>> Interface is 2 MMC and boot is 131073 and according to this
> > > >>>
> > > >>> static int is_boot_from_stream_device(u32 boot)
> > > >>> +{
> > > >>> + u32 interface;
> > > >>> +
> > > >>> + interface = boot >> 16;
> > > >>> + if (interface >= BT_DEV_TYPE_USB)
> > > >>> + return 1;
> > > >>> +
> > > >>> + if (interface == BT_DEV_TYPE_MMC && (boot & 1))
> > > >>> + return 1;
> > > >>> +
> > > >>> + return 0;
> > > >>> +}
> > > >>>
> > > >>> means a stream interface but it does not boot.
> > > >>>
> > > >>> Boot from boot1 give 131072 that is boot1 this let device boot
> > > >>> because
> > > >>
> > > >> Who gives 131073? Boot from boot1, you mean emmc boot partition0?
> > > >>
> > > >>> is_boot_from_stream_device is 0 and romapi use
> > > >>> spl_romapi_load_image_seekable
> > > >>>
> > > >>> Remove boot & 1 condition let me boot from mmcblk0boot0 and
> > > >>> mmcblk0boot1 without any problem
> > > >>
> > > >> Have you enabled emmc fastboot in fuse?
> > > >>
> > > >> boot & 1 is checking emmc fastboot. emmc fastboot mode is actually
> > > >> stream device. If fastboot mode enabled, you need burn your
> > > >> flash.bin into offset 0. Not 32KB offset.
> > > >
> > > > The offset is correct and the spl is starting on boot0 but then it
> > > > should load the rest from
> > > > boot0 block and not from usb. And why in case of boot1 the 1 is not
> > > > present. I flash both on offset 0. Anyway I sent a patch
> > >
> > > I suspect you have eMMC fastboot enabled for boot0, but not for boot1.
> >
> > I think that was fuse this way
> >
> > # Alternative Boot ("Fast boot")
> > # =>[BT_FUSE_SEL | eMMC boot | USDHC1 EMMC]
> > FB: ucmd fuse prog -y 1 3 0x10002A00
> > # =>[Fast boot | 8-bit DDR | MMC High speed | 1.8V | eMMC reset enable]
> > FB: ucmd fuse prog -y 2 1 0x000000E7
> > # =>[Fast Boot Ack enable]
> > FB: ucmd fuse prog -y 2 2 0x00000001
> > # boot_bus_width: 2 (8-bit), reset_boot_bus_width: 0, boot_mode: 2 (use dual
> > data rate (DDR))
> > FB: ucmd mmc bootbus 0 2 0 2
> > # boot_ack: 1, boot_partition: 1 (Boot partition 1), 7 (User area),
> > partition_access: No access to boot partition (default)
> > FB: ucmd mmc partconf 0 1 1 0
> >
> > How is it supposed to work in this case?
> >
>
> Above settings use the boot0 for fastboot. When you switch to boot1 for fastboot, did you change the
> partconf setting to "mmc partconf 0 1 2 0"?
I don't need to use fastboot. I mean the idea is if I boot from block0
I want to continue there. BOOTROM
fill the mode but then it should be able to not fail. Am I right?
>
> If the ROM boots from emmc fastboot, it will set the bit0 to 1 to indicate the fastboot. Since at this time, ROM
> does not leave fastboot (just stop the clock), we should continue the stream mode read in SPL for FIT image load.
> So below checking is correct. If you continue the stream mode read, what is the failure do you meet?
> The codes will read max 640KB data from ROM to search to FIT header. Can it get the header or not?
>
It does not find the header, in this case and it's not problem of
size of 640Kb (I have extend it). My impression
is that is loading from mmcblk0 and not boot partition
Michael
> if (interface == BT_DEV_TYPE_MMC && (boot & 1))
> return 1;
>
> Best regards,
> Ye Li
>
> > Michael
> >
> >
> >
> > >
> > > Regards,
> > > Peng.
> > >
> > > >
> > > > Michael
> > > >
> > > >>
> > > >> Regards,
> > > >> Peng.
> > > >>
> > > >>>
> > > >>> mmc partconf 0
> > > >>> EXT_CSD[179], PARTITION_CONFIG:
> > > >>> BOOT_ACK: 0x0
> > > >>> BOOT_PARTITION_ENABLE: 0x1
> > > >>> PARTITION_ACCESS: 0x0
> > > >>>
> > > >>> and the board was fused already.
> > > >>>
> > > >>> Any idea why?
> > > >>>
> > > >>> Michael
> > > >>>
> > > >
> > > >
> > > >
> >
> >
> >
> > --
> > Michael Nazzareno Trimarchi
> > Co-Founder & Chief Executive Officer
> > M. +39 347 913 2170
> > michael at amarulasolutions.com
> > __________________________________
> >
> > Amarula Solutions BV
> > Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172
> > info at amarulasolutions.com
> > https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.ama
> > rulasolutions.com%2F&data=04%7C01%7Cye.li%40nxp.com%7C1e6a78bc
> > a6d441c39f8608d9475d2495%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%
> > 7C0%7C637619287640324977%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wL
> > jAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&s
> > data=xIsVMyj9Qp1vciZnjJJK1wAT7A8fLdNRAs9pp4tll%2F0%3D&reserved=
> > 0
--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
michael at amarulasolutions.com
__________________________________
Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
info at amarulasolutions.com
www.amarulasolutions.com
More information about the U-Boot
mailing list