[PATCH v3 00/10] AM642-EVM: Add USB support

[Praneeth Bajjuri]

Aswath, Suman, Dave, Gowtham, Vignesh

On 6/4/21 11:49 AM, Aswath Govindraju wrote:
> Hi Praneeth,
> 
> On 04/06/21 10:18 pm, Praneeth Bajjuri wrote:
>>
>>
>> On 6/4/21 11:30 AM, Aswath Govindraju wrote:
>>> The following series of patches add support for the following
>>> - Kconfig symbol for giving the load address for ATF
>>> - USB Mass storage boot mode in AM642-EVM
>>> - DFU boot mode in AM642-EVM
>>> - Host and peripheral modes for AM642-EVM in U-Boot
>>> - Set the USB PHY core voltage to 0.85V
>>>
>>> changes since v2,
>>> - Increased the max size of ATF in patch 9
>>
>> Please confirm if this is tested on ATF 2.5 too.
>>
> 
> Sorry, for not mentioning it.
> 
> Yes, this series was tested using ATF 2.5.

Ok , pulling to ti-u-boot.

Aswath:
1. Please send the updated series to upstream u-boot as well.
2. post the kernel dts change to mainline as well.

Vignesh,
Assuming you are pulling the KIG patch too.

Suman/Dave/Gowtham,
Assuming you are pulling the kernel patch too.



> 
> Thanks,
> Aswath
> 
>>
>>> - Added reviewed-by from Suman Anna in patch 1
>>> - Reworded the subject of patch 8
>>>
>>> changes since v1,
>>> - Corrected the default load address of ATF to
>>>     0x70000000
>>>
>>> Aswath Govindraju (10):
>>>     tools: k3_fit_atf: Add support for providing ATF load address using a
>>>       Kconfig symbol
>>>     arm: mach-k3: am642_init: Add support for USB boot mode
>>>     arm: mach-k3: am642_init: Do USB fixups to facilitate host and device
>>>       boot modes
>>>     board: ti: am64x: Set the core voltage of USB PHY to 0.85V
>>>     arm: dts: k3-am64-main: Add USB DT nodes
>>>     arm: dts: k3-am642-*-evm: Add USB support
>>>     arm: dts: k3-am642-evm-u-boot: Add U-Boot tags and fix the dr_mode to
>>>       peripheral for USB subsystem
>>>     configs: am64x_evm_*_defconfig: Rearrange the components in SRAM to
>>>       satisfy the limitations for USB DFU boot mode
>>>     arm: dts: k3-am64-main: Update the location of ATF in SRAM and
>>>       increase its max size
>>>     configs: am64: Enable configs to support USB host and device modes
>>>
>>>    arch/arm/dts/k3-am64-main.dtsi                | 32 ++++++++++++-
>>>    arch/arm/dts/k3-am642-evm-u-boot.dtsi         | 13 ++++++
>>>    arch/arm/dts/k3-am642-evm.dts                 | 18 ++++++++
>>>    arch/arm/dts/k3-am642-r5-evm.dts              | 18 ++++++++
>>>    arch/arm/mach-k3/Kconfig                      |  7 +++
>>>    arch/arm/mach-k3/am642_init.c                 | 46 ++++++++++++++++++-
>>>    arch/arm/mach-k3/config.mk                    |  1 +
>>>    arch/arm/mach-k3/include/mach/am64_hardware.h | 11 +++--
>>>    arch/arm/mach-k3/include/mach/am64_spl.h      |  6 ++-
>>>    board/ti/am64x/evm.c                          | 14 ++++++
>>>    configs/am64x_evm_a53_defconfig               | 40 ++++++++++++++++
>>>    configs/am64x_evm_r5_defconfig                | 38 +++++++++++++--
>>>    include/configs/am64x_evm.h                   | 15 +++++-
>>>    tools/k3_fit_atf.sh                           |  9 ++--
>>>    14 files changed, 251 insertions(+), 17 deletions(-)
>>>
>