[PATCH v3 00/10] AM642-EVM: Add USB support

[Praneeth Bajjuri]

On 6/4/21 11:53 AM, Praneeth Bajjuri wrote:
> Aswath, Suman, Dave, Gowtham, Vignesh
> 
> On 6/4/21 11:49 AM, Aswath Govindraju wrote:
>> Hi Praneeth,
>>
>> On 04/06/21 10:18 pm, Praneeth Bajjuri wrote:
>>>
>>>
>>> On 6/4/21 11:30 AM, Aswath Govindraju wrote:
>>>> The following series of patches add support for the following
>>>> - Kconfig symbol for giving the load address for ATF
>>>> - USB Mass storage boot mode in AM642-EVM
>>>> - DFU boot mode in AM642-EVM
>>>> - Host and peripheral modes for AM642-EVM in U-Boot
>>>> - Set the USB PHY core voltage to 0.85V
>>>>
>>>> changes since v2,
>>>> - Increased the max size of ATF in patch 9
>>>
>>> Please confirm if this is tested on ATF 2.5 too.
>>>
>>
>> Sorry, for not mentioning it.
>>
>> Yes, this series was tested using ATF 2.5.
> 
> Ok , pulling to ti-u-boot.
> 
> Aswath:
> 1. Please send the updated series to upstream u-boot as well.
> 2. post the kernel dts change to mainline as well.
> 
> Vignesh,
> Assuming you are pulling the KIG patch too.
> 
> Suman/Dave/Gowtham,
> Assuming you are pulling the kernel patch too.

Please ignore this mail. was reviewing product baseline for same feature.

> 
> 
> 
>>
>> Thanks,
>> Aswath
>>
>>>
>>>> - Added reviewed-by from Suman Anna in patch 1
>>>> - Reworded the subject of patch 8
>>>>
>>>> changes since v1,
>>>> - Corrected the default load address of ATF to
>>>>     0x70000000
>>>>
>>>> Aswath Govindraju (10):
>>>>     tools: k3_fit_atf: Add support for providing ATF load address 
>>>> using a
>>>>       Kconfig symbol
>>>>     arm: mach-k3: am642_init: Add support for USB boot mode
>>>>     arm: mach-k3: am642_init: Do USB fixups to facilitate host and 
>>>> device
>>>>       boot modes
>>>>     board: ti: am64x: Set the core voltage of USB PHY to 0.85V
>>>>     arm: dts: k3-am64-main: Add USB DT nodes
>>>>     arm: dts: k3-am642-*-evm: Add USB support
>>>>     arm: dts: k3-am642-evm-u-boot: Add U-Boot tags and fix the 
>>>> dr_mode to
>>>>       peripheral for USB subsystem
>>>>     configs: am64x_evm_*_defconfig: Rearrange the components in SRAM to
>>>>       satisfy the limitations for USB DFU boot mode
>>>>     arm: dts: k3-am64-main: Update the location of ATF in SRAM and
>>>>       increase its max size
>>>>     configs: am64: Enable configs to support USB host and device modes
>>>>
>>>>    arch/arm/dts/k3-am64-main.dtsi                | 32 ++++++++++++-
>>>>    arch/arm/dts/k3-am642-evm-u-boot.dtsi         | 13 ++++++
>>>>    arch/arm/dts/k3-am642-evm.dts                 | 18 ++++++++
>>>>    arch/arm/dts/k3-am642-r5-evm.dts              | 18 ++++++++
>>>>    arch/arm/mach-k3/Kconfig                      |  7 +++
>>>>    arch/arm/mach-k3/am642_init.c                 | 46 
>>>> ++++++++++++++++++-
>>>>    arch/arm/mach-k3/config.mk                    |  1 +
>>>>    arch/arm/mach-k3/include/mach/am64_hardware.h | 11 +++--
>>>>    arch/arm/mach-k3/include/mach/am64_spl.h      |  6 ++-
>>>>    board/ti/am64x/evm.c                          | 14 ++++++
>>>>    configs/am64x_evm_a53_defconfig               | 40 ++++++++++++++++
>>>>    configs/am64x_evm_r5_defconfig                | 38 +++++++++++++--
>>>>    include/configs/am64x_evm.h                   | 15 +++++-
>>>>    tools/k3_fit_atf.sh                           |  9 ++--
>>>>    14 files changed, 251 insertions(+), 17 deletions(-)
>>>>
>>