[RFC Patch] arm: kirkwood: nsa310s: Use Marvell uclass mvgbe and PHY driver for DM Ethernet
Tony Dinh
mibodhi at gmail.com
Sat Apr 9 02:48:20 CEST 2022
Hi Stefan,
On Thu, Apr 7, 2022 at 10:55 PM Tony Dinh <mibodhi at gmail.com> wrote:
>
> On Thu, Apr 7, 2022 at 10:39 PM Stefan Roese <sr at denx.de> wrote:
> >
> > Hi Tony,
> >
> > On 4/8/22 07:03, Tony Dinh wrote:
> > > Hi all,
> > >
> > > This is a work-in-progress patch that I'm working on, to clean up the
> > > DM Ethernet code for the Zyxel NSA310S board (Kirkwood 88F6702 A1).
> > >
> > > This NSA310s board Ethernet has some quirks that it does not work
> > > quite the same way as other Kirwood boards with the similar network
> > > chip (MV88E1318), such as the Sheevaplug and the Dreamplug.
> > >
> > > Currently, in the NSA310S board file we use CONFIG_RESET_PHY_R to
> > > execute reset_phy() during initialization. And the reset_phy() code in
> > > this board file is ad-hoc, does not involve Marvell PHY driver (which
> > > it should be). So I'm following the same pattern that I've done for
> > > the Sheevaplug: use the uclass drivers/net/mvgbe.c (CONFIG_MVGBE) to
> > > bring up Ethernet, removing the reset_phy() code, and enable
> > > CONFIG_PHY_MARVEL.
> > >
> > > With this board, I could not get it to work the same way as for the
> > > Sheevaplug to bring up the PHY automatically. I had to insert the
> > > ad-hoc code to set RGMII delay in the __mvgbe_phy_init() function in
> > > mvgbe.c, so the phy_connect() call will find the PHY. The PHY Id is
> > > 1410e90, same as in the Sheevaplug and Dreamplug. Please see this in
> > > the patch below (it's only a hack to see the PHY can be brought up
> > > this way).
> >
> > Looking at drivers/net/phy/marvell.c I see that m88e1310_config()
> > does exactly this rx/tx delay configuration:
> >
> > /* Marvell 88E1310 */
> > static int m88e1310_config(struct phy_device *phydev)
> > {
> > ...
> > /* Set RGMII delay */
> > phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_PAGE, 0x0002);
> > reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_RGMII_CTRL);
> > reg |= 0x0030;
> > phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_RGMII_CTRL, reg);
> >
> > Are you sure that this functions is not called while probing /
> > enabling the network interface?
> >
> > > With the Sheevaplug and Dreamplug, there is no need to do this hack.
> > > The uclass mvgbe did all the work, by the time phy_connect() is
> > > executed, the PHY was already up and working fine. And then the
> > > Marvell PHY driver kicks in, setting up the rest.
> > >
> > > Perhaps we need code in the uclass MVGBE that handles this in a
> > > generic way? These are the Marvell PHY driver functions invoked after
> > > phy_connect() was successful. This happens in all 3 boards
> > > (Sheevaplug, Dreamplug, and NSA310s).
> > >
> > > m88e1310_config
> > > m88e1011s_startup
> >
> > Ah okay, It's executed.
> >
> > > I would appreciate hearing some explanation and perhaps some
> > > suggestion/guidance about this topic.
> >
> > If all 3 boards use the same ethernet driver with the same configuration
> > (e.g. CONFIG_PHYLIB, CONFIG_EM_ETH etc) and the same PHY, there should
> > of course be no need to handle this differently for this Zyxel board.
> > I suggest to continue debugging to see, why this really is necessary.
> > Perhaps some soft-reset of the PHY clears this rx/tx delay again?
>
> That's interesting. I recall trying miiphy_reset before phy_connect,
> but not phy_reset. I'll try that.
>
> By the way, without doing something to make the PHY available at that
> point, the phy_connect would fail, so the Marvell PHY driver was never
> invoked later.
I've tried the soft phy_reset (instead of the ad-hoc code for RGMII),
the board just hangs, and I need to recycle the power to reboot.
> > Additionally your patch seems to be indented incorrectly. This makes
> > reviewing a bit harder.
I will send in the V2 patch shortly.
Thanks,
Tony
>
> Sorry about that! I forgot to run checkpatch since it is an RFC patch.
> Will send the V2 patch for this.
>
> Thanks for looking at this,
> Tony
>
>
> >
> > Thanks,
> > Stefan
> >
> > > Thanks,
> > > Tony
> > >
> > > diff --git a/board/zyxel/nsa310s/nsa310s.c b/board/zyxel/nsa310s/nsa310s.c
> > > index b71de4e11f..78d472d56c 100644
> > > --- a/board/zyxel/nsa310s/nsa310s.c
> > > +++ b/board/zyxel/nsa310s/nsa310s.c
> > > @@ -1,22 +1,49 @@
> > > // SPDX-License-Identifier: GPL-2.0+
> > > /*
> > > - * Copyright (C) 2015, 2021 Tony Dinh <mibodhi at gmail.com>
> > > + * Copyright (C) 2015, 2021-2022 Tony Dinh <mibodhi at gmail.com>
> > > * Copyright (C) 2015 Gerald Kerma <dreagle at doukki.net>
> > > */
> > >
> > > #include <common.h>
> > > #include <init.h>
> > > -#include <miiphy.h>
> > > -#include <net.h>
> > > +#include <netdev.h>
> > > #include <asm/arch/cpu.h>
> > > #include <asm/arch/soc.h>
> > > #include <asm/arch/mpp.h>
> > > #include <asm/global_data.h>
> > > #include <asm/io.h>
> > > -#include "nsa310s.h"
> > > +#include <linux/bitops.h>
> > >
> > > DECLARE_GLOBAL_DATA_PTR;
> > >
> > > +/*
> > > + * low GPIO's
> > > + */
> > > +#define HDD1_GREEN_LED BIT(16)
> > > +#define HDD1_RED_LED BIT(13)
> > > +#define USB_GREEN_LED BIT(15)
> > > +#define USB_POWER BIT(21)
> > > +#define SYS_GREEN_LED BIT(28)
> > > +#define SYS_ORANGE_LED BIT(29)
> > > +
> > > +#define COPY_GREEN_LED BIT(22)
> > > +#define COPY_RED_LED BIT(23)
> > > +
> > > +#define PIN_USB_GREEN_LED 15
> > > +#define PIN_USB_POWER 21
> > > +
> > > +#define NSA310S_OE_LOW (~(0))
> > > +#define NSA310S_VAL_LOW (SYS_GREEN_LED | USB_POWER)
> > > +
> > > +/*
> > > + * high GPIO's
> > > +*/
> > > +#define HDD2_GREEN_LED BIT(2)
> > > +#define HDD2_POWER BIT(1)
> > > +
> > > +#define NSA310S_OE_HIGH (~(0))
> > > +#define NSA310S_VAL_HIGH (HDD2_POWER)
> > > +
> > > int board_early_init_f(void)
> > > {
> > > /*
> > > @@ -80,87 +107,7 @@ int board_init(void)
> > > return 0;
> > > }
> > >
> > > -static int fdt_get_phy_addr(const char *path)
> > > +int board_eth_init(struct bd_info *bis)
> > > {
> > > - const void *fdt = gd->fdt_blob;
> > > - const u32 *reg;
> > > - const u32 *val;
> > > - int node, phandle, addr;
> > > -
> > > - /* Find the node by its full path */
> > > - node = fdt_path_offset(fdt, path);
> > > - if (node >= 0) {
> > > - /* Look up phy-handle */
> > > - val = fdt_getprop(fdt, node, "phy-handle", NULL);
> > > - if (val) {
> > > - phandle = fdt32_to_cpu(*val);
> > > - if (!phandle)
> > > - return -1;
> > > - /* Follow it to its node */
> > > - node = fdt_node_offset_by_phandle(fdt, phandle);
> > > - if (node) {
> > > - /* Look up reg */
> > > - reg = fdt_getprop(fdt, node, "reg", NULL);
> > > - if (reg) {
> > > - addr = fdt32_to_cpu(*reg);
> > > - return addr;
> > > - }
> > > - }
> > > - }
> > > - }
> > > - return -1;
> > > -}
> > > -
> > > -#ifdef CONFIG_RESET_PHY_R
> > > -void reset_phy(void)
> > > -{
> > > - u16 reg;
> > > - u16 phyaddr;
> > > - char *name = "ethernet-controller at 72000";
> > > - char *eth0_path = "/ocp at f1000000/ethernet-controller at 72000/ethernet0-port at 0";
> > > -
> > > - if (miiphy_set_current_dev(name))
> > > - return;
> > > -
> > > - phyaddr = fdt_get_phy_addr(eth0_path);
> > > - if (phyaddr < 0)
> > > - return;
> > > -
> > > - /* set RGMII delay */
> > > - miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
> > > - miiphy_read(name, phyaddr, MV88E1318_MAC_CTRL_REG, ®);
> > > - reg |= (MV88E1318_RGMII_RX_CTRL | MV88E1318_RGMII_TX_CTRL);
> > > - miiphy_write(name, phyaddr, MV88E1318_MAC_CTRL_REG, reg);
> > > - miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, 0);
> > > -
> > > - /* reset PHY */
> > > - if (miiphy_reset(name, phyaddr))
> > > - return;
> > > -
> > > - /*
> > > - * ZyXEL NSA310S uses the 88E1310S Alaska (interface identical to 88E1318)
> > > - * and has an MCU attached to the LED[2] via tristate interrupt
> > > - */
> > > -
> > > - /* switch to LED register page */
> > > - miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
> > > - /* read out LED polarity register */
> > > - miiphy_read(name, phyaddr, MV88E1318_LED_POL_REG, ®);
> > > - /* clear 4, set 5 - LED2 low, tri-state */
> > > - reg &= ~(MV88E1318_LED2_4);
> > > - reg |= (MV88E1318_LED2_5);
> > > - /* write back LED polarity register */
> > > - miiphy_write(name, phyaddr, MV88E1318_LED_POL_REG, reg);
> > > - /* jump back to page 0, per the PHY chip documenation. */
> > > - miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, 0);
> > > -
> > > - /* set PHY back to auto-negotiation mode */
> > > - miiphy_write(name, phyaddr, 0x4, 0x1e1);
> > > - miiphy_write(name, phyaddr, 0x9, 0x300);
> > > - /* downshift */
> > > - miiphy_write(name, phyaddr, 0x10, 0x3860);
> > > - miiphy_write(name, phyaddr, 0x0, 0x9140);
> > > -
> > > - printf("MV88E1318 PHY initialized on %s\n", name);
> > > + return cpu_eth_init(bis);
> > > }
> > > -#endif /* CONFIG_RESET_PHY_R */
> > > diff --git a/configs/nsa310s_defconfig b/configs/nsa310s_defconfig
> > > index 05a6761854..07c96489c0 100644
> > > --- a/configs/nsa310s_defconfig
> > > +++ b/configs/nsa310s_defconfig
> > > @@ -2,6 +2,7 @@ CONFIG_ARM=y
> > > CONFIG_SKIP_LOWLEVEL_INIT=y
> > > CONFIG_SYS_DCACHE_OFF=y
> > > CONFIG_ARCH_CPU_INIT=y
> > > +CONFIG_SYS_THUMB_BUILD=y
> > > CONFIG_ARCH_KIRKWOOD=y
> > > CONFIG_SYS_KWD_CONFIG="board/zyxel/nsa310s/kwbimage.cfg"
> > > CONFIG_SYS_TEXT_BASE=0x600000
> > > @@ -31,6 +32,7 @@ CONFIG_CMD_PING=y
> > > CONFIG_CMD_EXT2=y
> > > CONFIG_CMD_FAT=y
> > > CONFIG_CMD_JFFS2=y
> > > +CONFIG_CMD_FS_GENERIC=y
> > > CONFIG_CMD_MTDPARTS=y
> > > CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xe0000 at 0x0(uboot),0x20000 at 0xe0000(uboot_env),0x100000 at 0x100000(second_stage_uboot),- at 0x200000(root)"
> > > CONFIG_CMD_UBI=y
> > > @@ -47,6 +49,7 @@ CONFIG_SYS_SATA_MAX_DEVICE=1
> > > # CONFIG_MMC is not set
> > > CONFIG_MTD=y
> > > CONFIG_MTD_RAW_NAND=y
> > > +CONFIG_PHY_MARVELL=y
> > > CONFIG_DM_ETH=y
> > > CONFIG_MVGBE=y
> > > CONFIG_MII=y
> > > diff --git a/drivers/net/mvgbe.c b/drivers/net/mvgbe.c
> > > index 954bf86121..9aff72bc74 100644
> > > --- a/drivers/net/mvgbe.c
> > > +++ b/drivers/net/mvgbe.c
> > > @@ -726,6 +726,13 @@ static int mvgbe_recv(struct eth_device *dev)
> > > }
> > > #endif
> > >
> > > +/* PHY related */
> > > +#define MV88E1318_PGADR_REG 22
> > > +#define MV88E1318_MAC_CTRL_PG 2
> > > +#define MV88E1318_MAC_CTRL_REG 21
> > > +#define MV88E1318_RGMII_TX_CTRL (1 << 4)
> > > +#define MV88E1318_RGMII_RX_CTRL (1 << 5)
> > > +
> > > #if defined(CONFIG_PHYLIB) || defined(CONFIG_DM_ETH)
> > > #if defined(CONFIG_DM_ETH)
> > > static struct phy_device *__mvgbe_phy_init(struct udevice *dev,
> > > @@ -740,11 +747,19 @@ static struct phy_device
> > > *__mvgbe_phy_init(struct eth_device *dev,
> > > #endif
> > > {
> > > struct phy_device *phydev;
> > > + int reg;
> > >
> > > /* Set phy address of the port */
> > > miiphy_write(dev->name, MV_PHY_ADR_REQUEST, MV_PHY_ADR_REQUEST,
> > > phyid);
> > >
> > > + /* Set RGMII delay */
> > > + miiphy_write(dev->name, phyid, MV88E1318_PGADR_REG,
> > > MV88E1318_MAC_CTRL_PG);
> > > + miiphy_read(dev->name, phyid, MV88E1318_MAC_CTRL_REG, ®);
> > > + reg |= (MV88E1318_RGMII_RX_CTRL | MV88E1318_RGMII_TX_CTRL);
> > > + miiphy_write(dev->name, phyid, MV88E1318_MAC_CTRL_REG, reg);
> > > + miiphy_write(dev->name, phyid, MV88E1318_PGADR_REG, 0);
> > > +
> > > phydev = phy_connect(bus, phyid, dev, phy_interface);
> > > if (!phydev) {
> > > printf("phy_connect failed\n");
> >
> > Viele Grüße,
> > Stefan Roese
> >
> > --
> > DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> > Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
More information about the U-Boot
mailing list