[PATCH 03/12] ARM: dts: sun4i: Sync from Linux v5.18-rc1
Samuel Holland
samuel at sholland.org
Wed Apr 27 22:31:22 CEST 2022
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetree:
- sun4i-a10-topwise-a721.dts
While this update should not impact any existing U-Boot functionality,
the changes to the USB PHY detection GPIO properties are needed to
convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <samuel at sholland.org>
---
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/axp209.dtsi | 6 +-
arch/arm/dts/sun4i-a10-a1000.dts | 31 ++-
arch/arm/dts/sun4i-a10-ba10-tvbox.dts | 2 +-
arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts | 20 +-
arch/arm/dts/sun4i-a10-cubieboard.dts | 16 +-
arch/arm/dts/sun4i-a10-dserve-dsrv9703c.dts | 21 +-
arch/arm/dts/sun4i-a10-hackberry.dts | 2 +-
arch/arm/dts/sun4i-a10-hyundai-a7hd.dts | 20 +-
arch/arm/dts/sun4i-a10-inet1.dts | 21 +-
arch/arm/dts/sun4i-a10-inet97fv2.dts | 22 +-
arch/arm/dts/sun4i-a10-inet9f-rev03.dts | 74 ++----
.../dts/sun4i-a10-itead-iteaduino-plus.dts | 2 +-
arch/arm/dts/sun4i-a10-jesurun-q5.dts | 4 +-
arch/arm/dts/sun4i-a10-marsboard.dts | 22 +-
arch/arm/dts/sun4i-a10-olinuxino-lime.dts | 33 +--
arch/arm/dts/sun4i-a10-pcduino.dts | 20 +-
arch/arm/dts/sun4i-a10-pov-protab2-ips9.dts | 21 +-
arch/arm/dts/sun4i-a10-topwise-a721.dts | 242 ++++++++++++++++++
arch/arm/dts/sun4i-a10.dtsi | 135 +++++++++-
20 files changed, 462 insertions(+), 255 deletions(-)
create mode 100644 arch/arm/dts/sun4i-a10-topwise-a721.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ab2d0da192..48ede8888e 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -539,7 +539,8 @@ dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-olinuxino-lime.dtb \
sun4i-a10-pcduino.dtb \
sun4i-a10-pcduino2.dtb \
- sun4i-a10-pov-protab2-ips9.dtb
+ sun4i-a10-pov-protab2-ips9.dtb \
+ sun4i-a10-topwise-a721.dtb
dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a10s-auxtek-t003.dtb \
sun5i-a10s-auxtek-t004.dtb \
diff --git a/arch/arm/dts/axp209.dtsi b/arch/arm/dts/axp209.dtsi
index 0d9ff12bdf..ca240cd6f6 100644
--- a/arch/arm/dts/axp209.dtsi
+++ b/arch/arm/dts/axp209.dtsi
@@ -53,7 +53,7 @@
interrupt-controller;
#interrupt-cells = <1>;
- ac_power_supply: ac-power-supply {
+ ac_power_supply: ac-power {
compatible = "x-powers,axp202-ac-power-supply";
status = "disabled";
};
@@ -69,7 +69,7 @@
#gpio-cells = <2>;
};
- battery_power_supply: battery-power-supply {
+ battery_power_supply: battery-power {
compatible = "x-powers,axp209-battery-power-supply";
status = "disabled";
};
@@ -112,7 +112,7 @@
};
};
- usb_power_supply: usb-power-supply {
+ usb_power_supply: usb-power {
compatible = "x-powers,axp202-usb-power-supply";
status = "disabled";
};
diff --git a/arch/arm/dts/sun4i-a10-a1000.dts b/arch/arm/dts/sun4i-a10-a1000.dts
index 6c254ec4c8..20f9ed2448 100644
--- a/arch/arm/dts/sun4i-a10-a1000.dts
+++ b/arch/arm/dts/sun4i-a10-a1000.dts
@@ -60,15 +60,26 @@
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
- red {
+ led-0 {
label = "a1000:red:usr";
gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>;
};
- blue {
+ led-1 {
label = "a1000:blue:pwr";
gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
default-state = "on";
@@ -125,7 +136,7 @@
};
&emac {
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
@@ -133,6 +144,20 @@
status = "okay";
};
+&de {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-ba10-tvbox.dts b/arch/arm/dts/sun4i-a10-ba10-tvbox.dts
index 38a2c41349..816d534ac0 100644
--- a/arch/arm/dts/sun4i-a10-ba10-tvbox.dts
+++ b/arch/arm/dts/sun4i-a10-ba10-tvbox.dts
@@ -68,7 +68,7 @@
};
&emac {
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
diff --git a/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts b/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts
index cf7b392dff..7426298888 100644
--- a/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts
+++ b/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts
@@ -131,20 +131,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
-};
-
®_usb0_vbus {
status = "okay";
};
@@ -165,10 +151,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-cubieboard.dts b/arch/arm/dts/sun4i-a10-cubieboard.dts
index 197a1f2b75..0645d60642 100644
--- a/arch/arm/dts/sun4i-a10-cubieboard.dts
+++ b/arch/arm/dts/sun4i-a10-cubieboard.dts
@@ -75,12 +75,12 @@
pinctrl-names = "default";
pinctrl-0 = <&led_pins_cubieboard>;
- blue {
+ led-0 {
label = "cubieboard:blue:usr";
gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* LED1 */
};
- green {
+ led-1 {
label = "cubieboard:green:usr";
gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* LED2 */
linux,default-trigger = "heartbeat";
@@ -114,7 +114,7 @@
};
&emac {
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
@@ -184,12 +184,6 @@
function = "gpio_out";
drive-strength = <20>;
};
-
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
};
®_ahci_5v {
@@ -254,9 +248,7 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-dserve-dsrv9703c.dts b/arch/arm/dts/sun4i-a10-dserve-dsrv9703c.dts
index 896e27a087..63e77c05bf 100644
--- a/arch/arm/dts/sun4i-a10-dserve-dsrv9703c.dts
+++ b/arch/arm/dts/sun4i-a10-dserve-dsrv9703c.dts
@@ -62,6 +62,7 @@
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ power-supply = <®_vcc3v3>;
};
chosen {
@@ -158,20 +159,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
-};
-
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pin>;
@@ -223,10 +210,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-hackberry.dts b/arch/arm/dts/sun4i-a10-hackberry.dts
index cc988ccd5c..47dea09225 100644
--- a/arch/arm/dts/sun4i-a10-hackberry.dts
+++ b/arch/arm/dts/sun4i-a10-hackberry.dts
@@ -80,7 +80,7 @@
};
&emac {
- phy = <&phy0>;
+ phy-handle = <&phy0>;
status = "okay";
};
diff --git a/arch/arm/dts/sun4i-a10-hyundai-a7hd.dts b/arch/arm/dts/sun4i-a10-hyundai-a7hd.dts
index f63767cddd..bf2044bac4 100644
--- a/arch/arm/dts/sun4i-a10-hyundai-a7hd.dts
+++ b/arch/arm/dts/sun4i-a10-hyundai-a7hd.dts
@@ -86,20 +86,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
-};
-
®_usb0_vbus {
status = "okay";
};
@@ -121,10 +107,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-inet1.dts b/arch/arm/dts/sun4i-a10-inet1.dts
index 26d0c1d6a0..60e432a0ef 100644
--- a/arch/arm/dts/sun4i-a10-inet1.dts
+++ b/arch/arm/dts/sun4i-a10-inet1.dts
@@ -62,6 +62,7 @@
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ power-supply = <®_vcc3v3>;
};
chosen {
@@ -164,20 +165,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
-};
-
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pin>;
@@ -233,10 +220,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
diff --git a/arch/arm/dts/sun4i-a10-inet97fv2.dts b/arch/arm/dts/sun4i-a10-inet97fv2.dts
index 5d096528e7..76016f2ca2 100644
--- a/arch/arm/dts/sun4i-a10-inet97fv2.dts
+++ b/arch/arm/dts/sun4i-a10-inet97fv2.dts
@@ -1,7 +1,7 @@
/*
* Copyright 2014 Open Source Support GmbH
*
- * David Lanzendörfer <david.lanzendoerfer at o2s.ch>
+ * David Lanzendörfer <david.lanzendoerfer at o2s.ch>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -150,20 +150,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
-};
-
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
@@ -209,10 +195,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-inet9f-rev03.dts b/arch/arm/dts/sun4i-a10-inet9f-rev03.dts
index 221acd10f6..0a562b2cc5 100644
--- a/arch/arm/dts/sun4i-a10-inet9f-rev03.dts
+++ b/arch/arm/dts/sun4i-a10-inet9f-rev03.dts
@@ -61,10 +61,6 @@
gpio-keys {
compatible = "gpio-keys-polled";
- pinctrl-names = "default";
- pinctrl-0 = <&key_pins_inet9f>;
- #address-cells = <1>;
- #size-cells = <0>;
poll-interval = <20>;
left-joystick-left {
@@ -72,7 +68,7 @@
linux,code = <ABS_X>;
linux,input-type = <EV_ABS>;
linux,input-value = <0xffffffff>; /* -1 */
- gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
+ gpios = <&pio 0 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA6 */
};
left-joystick-right {
@@ -80,7 +76,7 @@
linux,code = <ABS_X>;
linux,input-type = <EV_ABS>;
linux,input-value = <1>;
- gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
+ gpios = <&pio 0 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA5 */
};
left-joystick-up {
@@ -88,7 +84,7 @@
linux,code = <ABS_Y>;
linux,input-type = <EV_ABS>;
linux,input-value = <0xffffffff>; /* -1 */
- gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
+ gpios = <&pio 0 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA8 */
};
left-joystick-down {
@@ -96,7 +92,7 @@
linux,code = <ABS_Y>;
linux,input-type = <EV_ABS>;
linux,input-value = <1>;
- gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+ gpios = <&pio 0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA9 */
};
right-joystick-left {
@@ -104,7 +100,7 @@
linux,code = <ABS_Z>;
linux,input-type = <EV_ABS>;
linux,input-value = <0xffffffff>; /* -1 */
- gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
+ gpios = <&pio 0 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA1 */
};
right-joystick-right {
@@ -112,7 +108,7 @@
linux,code = <ABS_Z>;
linux,input-type = <EV_ABS>;
linux,input-value = <1>;
- gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
+ gpios = <&pio 0 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA0 */
};
right-joystick-up {
@@ -120,7 +116,7 @@
linux,code = <ABS_RZ>;
linux,input-type = <EV_ABS>;
linux,input-value = <0xffffffff>; /* -1 */
- gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
+ gpios = <&pio 0 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA3 */
};
right-joystick-down {
@@ -128,7 +124,7 @@
linux,code = <ABS_RZ>;
linux,input-type = <EV_ABS>;
linux,input-value = <1>;
- gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
+ gpios = <&pio 0 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA4 */
};
dpad-left {
@@ -136,7 +132,7 @@
linux,code = <ABS_HAT0X>;
linux,input-type = <EV_ABS>;
linux,input-value = <0xffffffff>; /* -1 */
- gpios = <&pio 7 23 GPIO_ACTIVE_LOW>; /* PH23 */
+ gpios = <&pio 7 23 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH23 */
};
dpad-right {
@@ -144,7 +140,7 @@
linux,code = <ABS_HAT0X>;
linux,input-type = <EV_ABS>;
linux,input-value = <1>;
- gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */
+ gpios = <&pio 7 24 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH24 */
};
dpad-up {
@@ -152,7 +148,7 @@
linux,code = <ABS_HAT0Y>;
linux,input-type = <EV_ABS>;
linux,input-value = <0xffffffff>; /* -1 */
- gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */
+ gpios = <&pio 7 25 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH25 */
};
dpad-down {
@@ -160,55 +156,55 @@
linux,code = <ABS_HAT0Y>;
linux,input-type = <EV_ABS>;
linux,input-value = <1>;
- gpios = <&pio 7 26 GPIO_ACTIVE_LOW>; /* PH26 */
+ gpios = <&pio 7 26 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH26 */
};
x {
label = "Button X";
linux,code = <BTN_X>;
- gpios = <&pio 0 16 GPIO_ACTIVE_LOW>; /* PA16 */
+ gpios = <&pio 0 16 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA16 */
};
y {
label = "Button Y";
linux,code = <BTN_Y>;
- gpios = <&pio 0 14 GPIO_ACTIVE_LOW>; /* PA14 */
+ gpios = <&pio 0 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA14 */
};
a {
label = "Button A";
linux,code = <BTN_A>;
- gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
+ gpios = <&pio 0 17 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA17 */
};
b {
label = "Button B";
linux,code = <BTN_B>;
- gpios = <&pio 0 15 GPIO_ACTIVE_LOW>; /* PA15 */
+ gpios = <&pio 0 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA15 */
};
select {
label = "Select Button";
linux,code = <BTN_SELECT>;
- gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
+ gpios = <&pio 0 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA11 */
};
start {
label = "Start Button";
linux,code = <BTN_START>;
- gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
+ gpios = <&pio 0 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA12 */
};
top-left {
label = "Top Left Button";
linux,code = <BTN_TL>;
- gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
+ gpios = <&pio 7 22 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH22 */
};
top-right {
label = "Top Right Button";
linux,code = <BTN_TR>;
- gpios = <&pio 0 13 GPIO_ACTIVE_LOW>; /* PA13 */
+ gpios = <&pio 0 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA13 */
};
};
};
@@ -308,30 +304,6 @@
status = "okay";
};
-&pio {
- key_pins_inet9f: key-pins {
- pins = "PA0", "PA1", "PA3", "PA4",
- "PA5", "PA6", "PA8", "PA9",
- "PA11", "PA12", "PA13",
- "PA14", "PA15", "PA16", "PA17",
- "PH22", "PH23", "PH24", "PH25", "PH26";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
-};
-
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
@@ -377,10 +349,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts b/arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts
index 80ecd78247..d4e319d16a 100644
--- a/arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts
+++ b/arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts
@@ -58,7 +58,7 @@
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins>;
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
diff --git a/arch/arm/dts/sun4i-a10-jesurun-q5.dts b/arch/arm/dts/sun4i-a10-jesurun-q5.dts
index 247fa27ef7..1aeb0bd551 100644
--- a/arch/arm/dts/sun4i-a10-jesurun-q5.dts
+++ b/arch/arm/dts/sun4i-a10-jesurun-q5.dts
@@ -63,7 +63,7 @@
leds {
compatible = "gpio-leds";
- green {
+ led {
label = "q5:green:usr";
gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
};
@@ -94,7 +94,7 @@
};
&emac {
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
diff --git a/arch/arm/dts/sun4i-a10-marsboard.dts b/arch/arm/dts/sun4i-a10-marsboard.dts
index 0dbf695765..81fdb217d3 100644
--- a/arch/arm/dts/sun4i-a10-marsboard.dts
+++ b/arch/arm/dts/sun4i-a10-marsboard.dts
@@ -62,22 +62,22 @@
leds {
compatible = "gpio-leds";
- red1 {
+ led-0 {
label = "marsboard:red1:usr";
gpios = <&pio 1 5 GPIO_ACTIVE_HIGH>;
};
- red2 {
+ led-1 {
label = "marsboard:red2:usr";
gpios = <&pio 1 6 GPIO_ACTIVE_HIGH>;
};
- red3 {
+ led-2 {
label = "marsboard:red3:usr";
gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>;
};
- red4 {
+ led-3 {
label = "marsboard:red4:usr";
gpios = <&pio 1 8 GPIO_ACTIVE_HIGH>;
};
@@ -105,7 +105,7 @@
};
&emac {
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
@@ -148,14 +148,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
®_usb1_vbus {
status = "okay";
};
@@ -183,9 +175,7 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/dts/sun4i-a10-olinuxino-lime.dts
index b74a614965..83d283cf66 100644
--- a/arch/arm/dts/sun4i-a10-olinuxino-lime.dts
+++ b/arch/arm/dts/sun4i-a10-olinuxino-lime.dts
@@ -74,7 +74,7 @@
pinctrl-names = "default";
pinctrl-0 = <&led_pins_olinuxinolime>;
- green {
+ led {
label = "a10-olinuxino-lime:green:usr";
gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
default-state = "on";
@@ -91,12 +91,11 @@
/*
* The A10-Lime is known to be unstable when running at 1008 MHz
*/
- operating-points = <
- /* kHz uV */
- 912000 1350000
- 864000 1300000
- 624000 1250000
- >;
+ operating-points =
+ /* kHz uV */
+ <912000 1350000>,
+ <864000 1300000>,
+ <624000 1250000>;
};
&de {
@@ -112,7 +111,7 @@
};
&emac {
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
@@ -186,18 +185,6 @@
function = "gpio_out";
drive-strength = <20>;
};
-
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
};
®_ahci_5v {
@@ -229,10 +216,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
diff --git a/arch/arm/dts/sun4i-a10-pcduino.dts b/arch/arm/dts/sun4i-a10-pcduino.dts
index b97a0f2f20..1ac82376ba 100644
--- a/arch/arm/dts/sun4i-a10-pcduino.dts
+++ b/arch/arm/dts/sun4i-a10-pcduino.dts
@@ -63,12 +63,12 @@
leds {
compatible = "gpio-leds";
- tx {
+ led-0 {
label = "pcduino:green:tx";
gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
};
- rx {
+ led-1 {
label = "pcduino:green:rx";
gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
};
@@ -76,8 +76,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
back {
label = "Key Back";
@@ -112,7 +110,7 @@
};
&emac {
- phy = <&phy1>;
+ phy-handle = <&phy1>;
status = "okay";
};
@@ -156,14 +154,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-};
-
#include "axp209.dtsi"
®_dcdc2 {
@@ -203,9 +193,7 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */
usb2_vbus-supply = <®_vcc5v0>; /* USB2 VBUS is always on */
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/dts/sun4i-a10-pov-protab2-ips9.dts
index 84b25be1ac..c325969476 100644
--- a/arch/arm/dts/sun4i-a10-pov-protab2-ips9.dts
+++ b/arch/arm/dts/sun4i-a10-pov-protab2-ips9.dts
@@ -62,6 +62,7 @@
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ power-supply = <®_vcc3v3>;
};
chosen {
@@ -146,20 +147,6 @@
status = "okay";
};
-&pio {
- usb0_id_detect_pin: usb0-id-detect-pin {
- pins = "PH4";
- function = "gpio_in";
- bias-pull-up;
- };
-
- usb0_vbus_detect_pin: usb0-vbus-detect-pin {
- pins = "PH5";
- function = "gpio_in";
- bias-pull-down;
- };
-};
-
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pin>;
@@ -211,10 +198,8 @@
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PH5 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
diff --git a/arch/arm/dts/sun4i-a10-topwise-a721.dts b/arch/arm/dts/sun4i-a10-topwise-a721.dts
new file mode 100644
index 0000000000..3628f12d25
--- /dev/null
+++ b/arch/arm/dts/sun4i-a10-topwise-a721.dts
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2020 Pascal Roeleven <dev at pascalroeleven.nl>
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Topwise A721";
+ compatible = "topwise,a721", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 100000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_vbat>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ brightness-levels = <0 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ panel {
+ compatible = "starry,kr070pe2t";
+ backlight = <&backlight>;
+ power-supply = <®_lcd_power>;
+
+ port {
+ panel_input: endpoint {
+ remote-endpoint = <&tcon0_out_panel>;
+ };
+ };
+ };
+
+ reg_lcd_power: reg-lcd-power {
+ compatible = "regulator-fixed";
+ regulator-name = "reg-lcd-power";
+ gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ enable-active-high;
+ };
+
+ reg_vbat: reg-vbat {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+};
+
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic at 34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ accelerometer at 4c {
+ compatible = "fsl,mma7660";
+ reg = <0x4c>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ touchscreen at 38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ vcc-supply = <®_vcc3v3>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button-571 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <571428>;
+ };
+
+ button-761 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <761904>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ vcc-pb-supply = <®_vcc3v3>;
+ vcc-pf-supply = <®_vcc3v3>;
+ vcc-ph-supply = <®_vcc3v3>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&tcon0_out {
+ tcon0_out_panel: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun4i-a10.dtsi b/arch/arm/dts/sun4i-a10.dtsi
index 3a1c6b45c9..51a6464aab 100644
--- a/arch/arm/dts/sun4i-a10.dtsi
+++ b/arch/arm/dts/sun4i-a10.dtsi
@@ -115,13 +115,12 @@
reg = <0x0>;
clocks = <&ccu CLK_CPU>;
clock-latency = <244144>; /* 8 32k periods */
- operating-points = <
+ operating-points =
/* kHz uV */
- 1008000 1400000
- 912000 1350000
- 864000 1300000
- 624000 1250000
- >;
+ <1008000 1400000>,
+ <912000 1350000>,
+ <864000 1300000>,
+ <624000 1250000>;
#cooling-cells = <2>;
};
};
@@ -143,7 +142,7 @@
trips {
cpu_alert0: cpu-alert0 {
/* milliCelsius */
- temperature = <850000>;
+ temperature = <85000>;
hysteresis = <2000>;
type = "passive";
};
@@ -184,14 +183,34 @@
status = "disabled";
};
+ pmu {
+ compatible = "arm,cortex-a8-pmu";
+ interrupts = <3>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /* Address must be kept in the lower 256 MiBs of DRAM for VE. */
+ default-pool {
+ compatible = "shared-dma-pool";
+ size = <0x6000000>;
+ alloc-ranges = <0x40000000 0x10000000>;
+ reusable;
+ linux,cma-default;
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
- sram-controller at 1c00000 {
- compatible = "allwinner,sun4i-a10-sram-controller";
+ system-control at 1c00000 {
+ compatible = "allwinner,sun4i-a10-system-control";
reg = <0x01c00000 0x30>;
#address-cells = <1>;
#size-cells = <1>;
@@ -224,6 +243,19 @@
status = "disabled";
};
};
+
+ sram_c: sram at 1d00000 {
+ compatible = "mmio-sram";
+ reg = <0x01d00000 0xd0000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x01d00000 0xd0000>;
+
+ ve_sram: sram-section at 0 {
+ compatible = "allwinner,sun4i-a10-sram-c1";
+ reg = <0x000000 0x80000>;
+ };
+ };
};
dma: dma-controller at 1c02000 {
@@ -234,7 +266,7 @@
#dma-cells = <2>;
};
- nfc: nand at 1c03000 {
+ nfc: nand-controller at 1c03000 {
compatible = "allwinner,sun4i-a10-nand";
reg = <0x01c03000 0x1000>;
interrupts = <37>;
@@ -309,6 +341,7 @@
"tcon-ch0",
"tcon-ch1";
clock-output-names = "tcon0-pixel-clock";
+ #clock-cells = <0>;
dmas = <&dma SUN4I_DMA_DEDICATED 14>;
ports {
@@ -358,6 +391,7 @@
"tcon-ch0",
"tcon-ch1";
clock-output-names = "tcon1-pixel-clock";
+ #clock-cells = <0>;
dmas = <&dma SUN4I_DMA_DEDICATED 15>;
ports {
@@ -394,6 +428,17 @@
};
};
+ video-codec at 1c0e000 {
+ compatible = "allwinner,sun4i-a10-video-engine";
+ reg = <0x01c0e000 0x1000>;
+ clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>,
+ <&ccu CLK_DRAM_VE>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_VE>;
+ interrupts = <53>;
+ allwinner,sram = <&ve_sram 1>;
+ };
+
mmc0: mmc at 1c0f000 {
compatible = "allwinner,sun4i-a10-mmc";
reg = <0x01c0f000 0x1000>;
@@ -450,13 +495,14 @@
phy-names = "usb";
extcon = <&usbphy 0>;
allwinner,sram = <&otg_sram 1>;
+ dr_mode = "otg";
status = "disabled";
};
usbphy: phy at 1c13400 {
#phy-cells = <1>;
compatible = "allwinner,sun4i-a10-usb-phy";
- reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>;
+ reg = <0x01c13400 0x10>, <0x01c14800 0x4>, <0x01c1c800 0x4>;
reg-names = "phy_ctrl", "pmu1", "pmu2";
clocks = <&ccu CLK_USB_PHY>;
clock-names = "usb_phy";
@@ -530,8 +576,6 @@
};
hdmi_out: port at 1 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
};
};
@@ -579,6 +623,16 @@
status = "disabled";
};
+ csi1: csi at 1c1d000 {
+ compatible = "allwinner,sun4i-a10-csi1";
+ reg = <0x01c1d000 0x1000>;
+ interrupts = <43>;
+ clocks = <&ccu CLK_AHB_CSI1>, <&ccu CLK_DRAM_CSI1>;
+ clock-names = "bus", "ram";
+ resets = <&ccu RST_CSI1>;
+ status = "disabled";
+ };
+
spi3: spi at 1c1f000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c1f000 0x1000>;
@@ -625,6 +679,31 @@
function = "can";
};
+ /omit-if-no-ref/
+ csi1_8bits_pg_pins: csi1-8bits-pg-pins {
+ pins = "PG0", "PG2", "PG3", "PG4", "PG5",
+ "PG6", "PG7", "PG8", "PG9", "PG10",
+ "PG11";
+ function = "csi1";
+ };
+
+ /omit-if-no-ref/
+ csi1_24bits_ph_pins: csi1-24bits-ph-pins {
+ pins = "PH0", "PH1", "PH2", "PH3", "PH4",
+ "PH5", "PH6", "PH7", "PH8", "PH9",
+ "PH10", "PH11", "PH12", "PH13", "PH14",
+ "PH15", "PH16", "PH17", "PH18", "PH19",
+ "PH20", "PH21", "PH22", "PH23", "PH24",
+ "PH25", "PH26", "PH27";
+ function = "csi1";
+ };
+
+ /omit-if-no-ref/
+ csi1_clk_pg_pin: csi1-clk-pg-pin {
+ pins = "PG1";
+ function = "csi1";
+ };
+
emac_pins: emac0-pins {
pins = "PA0", "PA1", "PA2",
"PA3", "PA4", "PA5", "PA6",
@@ -762,13 +841,20 @@
timer at 1c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
- interrupts = <22>;
+ interrupts = <22>,
+ <23>,
+ <24>,
+ <25>,
+ <67>,
+ <68>;
clocks = <&osc24M>;
};
wdt: watchdog at 1c20c90 {
compatible = "allwinner,sun4i-a10-wdt";
reg = <0x01c20c90 0x10>;
+ interrupts = <24>;
+ clocks = <&osc24M>;
};
rtc: rtc at 1c20d00 {
@@ -1001,6 +1087,27 @@
status = "disabled";
};
+ mali: gpu at 1c40000 {
+ compatible = "allwinner,sun4i-a10-mali", "arm,mali-400";
+ reg = <0x01c40000 0x10000>;
+ interrupts = <69>,
+ <70>,
+ <71>,
+ <72>,
+ <73>;
+ interrupt-names = "gp",
+ "gpmmu",
+ "pp0",
+ "ppmmu0",
+ "pmu";
+ clocks = <&ccu CLK_AHB_GPU>, <&ccu CLK_GPU>;
+ clock-names = "bus", "core";
+ resets = <&ccu RST_GPU>;
+
+ assigned-clocks = <&ccu CLK_GPU>;
+ assigned-clock-rates = <384000000>;
+ };
+
fe0: display-frontend at 1e00000 {
compatible = "allwinner,sun4i-a10-display-frontend";
reg = <0x01e00000 0x20000>;
--
2.35.1
More information about the U-Boot
mailing list