[PATCH v4] imx: support i.MX8QM DMSSE20 a1 board
Oliver Graute
oliver.graute at kococonnector.com
Tue Jul 12 12:14:45 CEST 2022
Add i.MX8QM DMSSE20 a1 board support
U-Boot 2022.07-00033-g2a5cf8e9e7 (Jul 12 2022 - 11:29:05 +0200)
Model: Advantech iMX8QM DMSSE20
Board: DMS-SE20A1 8GB
Build: SCFW 549b1e18, SECO-FW c9de51c0, ATF 5782363
Boot: USB
DRAM: 8 GiB
Core: 100 devices, 19 uclasses, devicetree: separate
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial at 5a060000
Out: serial at 5a060000
Err: serial at 5a060000
Net: eth0: ethernet at 5b040000
Warning: ethernet at 5b050000 (eth1) using random MAC address - aa:a2:be:5b:81:4a
, eth1: ethernet at 5b050000
Hit any key to stop autoboot: 0
Signed-off-by: Oliver Graute <oliver.graute at kococonnector.com>
---
Changes for v4
-update atf fw version
-update seco fw version
-update scfw version
-move CONFIG_IMX_SMMU to imx8qm_dmsse20a1_defconfig
-move CONFIG_LOADADDR to imx8qm_dmsse20a1_defconfig
-move CONFIG_SYS_LOAD_ADDR to imx8qm_dmsse20a1_defconfig
-move CONFIG_SYS_MALLOC_LEN to imx8qm_dmsse20a1_defconfig
-move CONFIG_SYS_MMC_IMG_LOAD_PART to imx8qm_dmsse20a1_defconfig
-move CONFIG_FSL_USDHC to imx8qm_dmsse20a1_defconfig
-replaced CONFIG_SPL_MMC_SUPPORT with CONFIG_SPL_MMC
-replaced CONFIG_SPL_SERIAL_SUPPORT with CONFIG_SPL_SERIAL
-drop CONFIG_FEC_XCV_TYPE
Changes for v3
-Remove addr parameter from reset_cpu()
-moved some configs into defconfig
Changes for v2
-replaced bd_t with struct bd_info
-added missing DTS in MAINTAINERS
-replaced README with imx8qm-dmsse20-a1.rst
-move CMD_FUSE to Kconfig
-removed fdt_high
-added i2c support
-added rtc support
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx8qm-dmsse20-a1.dts | 407 ++++++++++++++++++
arch/arm/mach-imx/imx8/Kconfig | 7 +
board/advantech/imx8qm_dmsse20_a1/Kconfig | 17 +
board/advantech/imx8qm_dmsse20_a1/MAINTAINERS | 7 +
board/advantech/imx8qm_dmsse20_a1/Makefile | 8 +
.../imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c | 188 ++++++++
.../advantech/imx8qm_dmsse20_a1/imximage.cfg | 21 +
board/advantech/imx8qm_dmsse20_a1/spl.c | 224 ++++++++++
common/Kconfig | 2 +-
configs/imx8qm_dmsse20a1_defconfig | 105 +++++
doc/board/advantech/imx8qm-dmsse20-a1.rst | 59 +++
doc/board/advantech/index.rst | 1 +
include/configs/imx8qm_dmsse20.h | 164 +++++++
14 files changed, 1210 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/imx8qm-dmsse20-a1.dts
create mode 100644 board/advantech/imx8qm_dmsse20_a1/Kconfig
create mode 100644 board/advantech/imx8qm_dmsse20_a1/MAINTAINERS
create mode 100644 board/advantech/imx8qm_dmsse20_a1/Makefile
create mode 100644 board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c
create mode 100644 board/advantech/imx8qm_dmsse20_a1/imximage.cfg
create mode 100644 board/advantech/imx8qm_dmsse20_a1/spl.c
create mode 100644 configs/imx8qm_dmsse20a1_defconfig
create mode 100644 doc/board/advantech/imx8qm-dmsse20-a1.rst
create mode 100644 include/configs/imx8qm_dmsse20.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index a7e0d9f6c0..50bc76289f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -920,6 +920,7 @@ dtb-$(CONFIG_ARCH_IMX8) += \
fsl-imx8qm-apalis.dtb \
fsl-imx8qm-mek.dtb \
imx8qm-cgtqmx8.dtb \
+ imx8qm-dmsse20-a1.dtb \
imx8qm-rom7720-a1.dtb \
fsl-imx8qxp-ai_ml.dtb \
fsl-imx8qxp-colibri.dtb \
diff --git a/arch/arm/dts/imx8qm-dmsse20-a1.dts b/arch/arm/dts/imx8qm-dmsse20-a1.dts
new file mode 100644
index 0000000000..81ef7fb2ce
--- /dev/null
+++ b/arch/arm/dts/imx8qm-dmsse20-a1.dts
@@ -0,0 +1,407 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017 NXP
+ */
+
+/dts-v1/;
+
+/* First 128KB is for PSCI ATF. */
+/memreserve/ 0x80000000 0x00020000;
+
+#include "fsl-imx8qm.dtsi"
+
+/ {
+ model = "Advantech iMX8QM DMSSE20";
+ compatible = "fsl,imx8qm-mek", "fsl,imx8qm";
+
+ aliases {
+ mmc0 = &usdhc1;
+ mmc2 = &usdhc3;
+ };
+
+ chosen {
+ bootargs = "console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200";
+ stdout-path = &lpuart0;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg1_vbus: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usdhc2_vmmc: usdhc2_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "sw-3p3-sd1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ busfreq {
+ status = "disabled";
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog_1>;
+
+ imx8qm-mek {
+ pinctrl_hog_1: hoggrp-1 {
+ fsl,pins = <
+ SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03 0x06000048
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD 0x000014a0
+ SC_P_ENET0_MDC_CONN_ENET0_MDC 0x06000020
+ SC_P_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020
+ SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x00000060
+ SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x00000060
+ SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x00000060
+ SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x00000060
+ SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x00000060
+ SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x00000060
+ SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x00000060
+ SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x00000060
+ SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x00000060
+ SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x00000060
+ SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x00000060
+ SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x00000060
+ >;
+ };
+
+ pinctrl_fec2: fec2grp {
+ fsl,pins = <
+ SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0
+ SC_P_ENET1_MDC_CONN_ENET1_MDC 0x06000020
+ SC_P_ENET1_MDIO_CONN_ENET1_MDIO 0x06000020
+ SC_P_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL 0x00000060
+ SC_P_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC 0x00000060
+ SC_P_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0 0x00000060
+ SC_P_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1 0x00000060
+ SC_P_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2 0x00000060
+ SC_P_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3 0x00000060
+ SC_P_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC 0x00000060
+ SC_P_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL 0x00000060
+ SC_P_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0 0x00000060
+ SC_P_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1 0x00000060
+ SC_P_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2 0x00000060
+ SC_P_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3 0x00000060
+ >;
+ };
+
+ pinctrl_lpi2c1: lpi2c1grp {
+ fsl,pins = <
+ SC_P_GPT0_CLK_DMA_I2C1_SCL 0xc600004c
+ SC_P_GPT0_CAPTURE_DMA_I2C1_SDA 0xc600004c
+ >;
+ };
+
+ pinctrl_lpi2c2: lpi2c2grp {
+ fsl,pins = <
+ SC_P_GPT1_CLK_DMA_I2C2_SCL 0xc600004c
+ SC_P_GPT1_CAPTURE_DMA_I2C2_SDA 0xc600004c
+ >;
+ };
+
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins = <
+ SC_P_UART0_RX_DMA_UART0_RX 0x06000020
+ SC_P_UART0_TX_DMA_UART0_TX 0x06000020
+ >;
+ };
+
+ pinctrl_rtc_mc_8803: rtc_mc_8803_grp{
+ fsl,pins = <
+ SC_P_SIM0_POWER_EN_DMA_I2C3_SDA 0xc600004c
+ SC_P_SIM0_PD_DMA_I2C3_SCL 0xc600004c
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
+ SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021
+ SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021
+ SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021
+ SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021
+ SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021
+ SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021
+ SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021
+ SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021
+ SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021
+ SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000041
+ SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040
+ SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020
+ SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020
+ SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020
+ SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020
+ SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020
+ SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020
+ SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020
+ SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020
+ SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020
+ SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000040
+ SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040
+ SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000020
+ SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000020
+ SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000020
+ SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000020
+ SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000020
+ SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000020
+ SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000020
+ SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000020
+ SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000020
+ SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000040
+ SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07 0x00000020
+ SC_P_USDHC1_VSELECT_LSIO_GPIO4_IO08 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc3_gpio: usdhc3grpgpio {
+ fsl,pins = <
+ SC_P_USDHC2_WP_LSIO_GPIO4_IO11 0x00000021
+ SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12 0x00000021
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041
+ SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021
+ SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021
+ SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021
+ SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021
+ SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021
+ SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040
+ SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020
+ SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020
+ SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020
+ SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020
+ SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020
+ SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ SC_P_USDHC1_CLK_CONN_USDHC1_CLK 0x06000040
+ SC_P_USDHC1_CMD_CONN_USDHC1_CMD 0x00000020
+ SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000020
+ SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000020
+ SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000020
+ SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000020
+ SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000041
+ SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000021
+ SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000021
+ SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000021
+ SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000021
+ SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000021
+ SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000021
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000040
+ SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000020
+ SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000020
+ SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000020
+ SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000020
+ SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000020
+ SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000020
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ SC_P_USDHC2_CLK_CONN_USDHC2_CLK 0x06000040
+ SC_P_USDHC2_CMD_CONN_USDHC2_CMD 0x00000020
+ SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0 0x00000020
+ SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1 0x00000020
+ SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2 0x00000020
+ SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3 0x00000020
+ SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT 0x00000020
+ >;
+ };
+ };
+};
+
+&gpio2 {
+ status = "okay";
+};
+
+&gpio4 {
+ status = "okay";
+};
+
+&gpio5 {
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default","state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,ar8031-phy-fixup;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec2>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy1>;
+ fsl,ar8031-phy-fixup;
+ fsl,magic-packet;
+ status = "okay";
+ fsl,mii-exclusive;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ };
+ };
+};
+
+&i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpi2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc_mc_8803>;
+ status = "okay";
+
+ rv8803 at 32 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "microcrystal,rv8803";
+ reg = <0x32>;
+ };
+
+ 24c02 at 50 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,24c04";
+ reg = <0x50>;
+ };
+};
+
+&lpuart0 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart0>;
+ status = "okay";
+};
diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig
index 5e1b20a422..bcb60b1e90 100644
--- a/arch/arm/mach-imx/imx8/Kconfig
+++ b/arch/arm/mach-imx/imx8/Kconfig
@@ -84,6 +84,12 @@ config TARGET_IMX8QM_ROM7720_A1
select SUPPORT_SPL
select IMX8QM
+config TARGET_IMX8QM_DMSSE20_A1
+ bool "Support i.MX8QM DMS-SE20-A1 board"
+ select BOARD_LATE_INIT
+ select SUPPORT_SPL
+ select IMX8QM
+
config TARGET_IMX8QXP_MEK
bool "Support i.MX8QXP MEK board"
select BOARD_LATE_INIT
@@ -97,6 +103,7 @@ endchoice
source "board/freescale/imx8qm_mek/Kconfig"
source "board/freescale/imx8qxp_mek/Kconfig"
source "board/congatec/cgtqmx8/Kconfig"
+source "board/advantech/imx8qm_dmsse20_a1/Kconfig"
source "board/advantech/imx8qm_rom7720_a1/Kconfig"
source "board/toradex/apalis-imx8/Kconfig"
source "board/toradex/colibri-imx8x/Kconfig"
diff --git a/board/advantech/imx8qm_dmsse20_a1/Kconfig b/board/advantech/imx8qm_dmsse20_a1/Kconfig
new file mode 100644
index 0000000000..f491462ea0
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/Kconfig
@@ -0,0 +1,17 @@
+if TARGET_IMX8QM_DMSSE20_A1
+
+config SYS_BOARD
+ default "imx8qm_dmsse20_a1"
+
+config SYS_VENDOR
+ default "advantech"
+
+config SYS_CONFIG_NAME
+ default "imx8qm_dmsse20"
+
+config IMX_CONFIG
+ default "board/advantech/imx8qm_dmsse20_a1/imximage.cfg"
+
+source "board/freescale/common/Kconfig"
+
+endif
diff --git a/board/advantech/imx8qm_dmsse20_a1/MAINTAINERS b/board/advantech/imx8qm_dmsse20_a1/MAINTAINERS
new file mode 100644
index 0000000000..8292c6ba71
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/MAINTAINERS
@@ -0,0 +1,7 @@
+i.MX8QM ROM DMSSE20 a1 BOARD
+M: Oliver Graute <oliver.graute at kococonnector.com>
+S: Maintained
+F: board/advantech/imx8qm_dmsse20_a1/
+F: arch/arm/dts/imx8qm-dmsse20-a1.dtb
+F: include/configs/imx8qm_dmsse20.h
+F: configs/imx8qm_dmsse20a1_defconfig
diff --git a/board/advantech/imx8qm_dmsse20_a1/Makefile b/board/advantech/imx8qm_dmsse20_a1/Makefile
new file mode 100644
index 0000000000..262ffcd683
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += imx8qm_dmsse20_a1.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c b/board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c
new file mode 100644
index 0000000000..c3bc26f80d
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/imx8qm_dmsse20_a1.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ * Copyright (C) 2020 Oliver Graute <oliver.graute at kococonnector.com>
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <linux/libfdt.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+/* #include <power-domain.h> */
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+static iomux_cfg_t uart0_pads[] = {
+ SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
+}
+
+int board_early_init_f(void)
+{
+ sc_pm_clock_rate_t rate = SC_80MHZ;
+ int ret;
+
+ /* Set UART0 clock root to 80 MHz */
+ ret = sc_pm_setup_uart(SC_R_UART_0, rate);
+ if (ret)
+ return ret;
+
+ setup_iomux_uart();
+
+ /* This is needed to because Kernel do not Power Up DC_0 */
+ sc_pm_set_resource_power_mode(-1, SC_R_DC_0, SC_PM_PW_MODE_ON);
+ sc_pm_set_resource_power_mode(-1, SC_R_GPIO_5, SC_PM_PW_MODE_ON);
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_FEC_MXC)
+#include <miiphy.h>
+
+int board_phy_config(struct phy_device *phydev)
+{
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MXC_GPIO
+
+#define LVDS_ENABLE IMX_GPIO_NR(1, 6)
+#define MIPI_ENABLE IMX_GPIO_NR(1, 7)
+
+#define BB_GPIO_3V3_1 IMX_GPIO_NR(4, 20)
+#define BB_GPIO_3V3_2 IMX_GPIO_NR(4, 24)
+#define BB_GPIO_3V3_3 IMX_GPIO_NR(4, 23)
+
+static void board_gpio_init(void)
+{
+ /* Enable BB 3V3 */
+ gpio_request(BB_GPIO_3V3_1, "bb_3v3_1");
+ gpio_direction_output(BB_GPIO_3V3_1, 1);
+ gpio_request(BB_GPIO_3V3_2, "bb_3v3_2");
+ gpio_direction_output(BB_GPIO_3V3_2, 1);
+ gpio_request(BB_GPIO_3V3_3, "bb_3v3_3");
+ gpio_direction_output(BB_GPIO_3V3_3, 1);
+
+ /* enable LVDS SAS boards */
+ gpio_request(LVDS_ENABLE, "lvds_enable");
+ gpio_direction_output(LVDS_ENABLE, 1);
+
+ /* enable MIPI SAS boards */
+ gpio_request(MIPI_ENABLE, "mipi_enable");
+ gpio_direction_output(MIPI_ENABLE, 1);
+}
+#endif
+
+int checkboard(void)
+{
+ puts("Board: DMS-SE20A1 8GB\n");
+ build_info();
+ print_bootinfo();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ if (IS_ENABLED(CONFIG_XEN))
+ return 0;
+
+#ifdef CONFIG_MXC_GPIO
+ board_gpio_init();
+#endif
+
+ return 0;
+}
+
+void board_quiesce_devices(void)
+{
+ if (IS_ENABLED(CONFIG_XEN)) {
+ /* Clear magic number to let xen know uboot is over */
+ writel(0x0, (void __iomem *)0x80000000);
+ return;
+ }
+}
+
+void detail_board_ddr_info(void)
+{
+ puts("\nDDR ");
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(void)
+{
+ puts("SCI reboot request");
+
+ while (1)
+ putc('.');
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+ return 0;
+}
+#endif
+
+int board_mmc_get_env_dev(int devno)
+{
+ /* Use EMMC */
+ if (IS_ENABLED(CONFIG_XEN))
+ return 0;
+
+ return devno;
+}
+
+int mmc_map_to_kernel_blk(int dev_no)
+{
+ /* Use EMMC */
+ if (IS_ENABLED(CONFIG_XEN))
+ return 0;
+
+ return dev_no;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ env_set("board_name", "DMS-SE20A1");
+ env_set("board_rev", "iMX8QM");
+#endif
+
+ env_set("sec_boot", "no");
+#ifdef CONFIG_AHAB_BOOT
+ env_set("sec_boot", "yes");
+#endif
+
+ return 0;
+}
diff --git a/board/advantech/imx8qm_dmsse20_a1/imximage.cfg b/board/advantech/imx8qm_dmsse20_a1/imximage.cfg
new file mode 100644
index 0000000000..e324c7ca37
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/imximage.cfg
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM SD 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-val-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 bl31.bin 0x80000000
+/* Add U-Boot image with load attribute */
+DATA A35 u-boot-dtb.bin 0x80020000
diff --git a/board/advantech/imx8qm_dmsse20_a1/spl.c b/board/advantech/imx8qm_dmsse20_a1/spl.c
new file mode 100644
index 0000000000..06bb049c3a
--- /dev/null
+++ b/board/advantech/imx8qm_dmsse20_a1/spl.c
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ */
+#include <common.h>
+#include <dm.h>
+#include <spl.h>
+#include <fsl_esdhc.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ESDHC_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ESDHC_CLK_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_INPUT_PAD_CTRL ((SC_PAD_CONFIG_OD_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_NORMAL_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define FSPI_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define GPIO_PAD_CTRL ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define I2C_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_LOW << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+#ifdef CONFIG_FSL_ESDHC_IMX
+
+#define USDHC1_CD_GPIO IMX_GPIO_NR(5, 22)
+#define USDHC2_CD_GPIO IMX_GPIO_NR(4, 12)
+
+static struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
+ {USDHC1_BASE_ADDR, 0, 8},
+ {USDHC3_BASE_ADDR, 0, 4},
+};
+
+static iomux_cfg_t emmc0[] = {
+ SC_P_EMMC0_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+ SC_P_EMMC0_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA4 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA5 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA6 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_DATA7 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_EMMC0_STROBE | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+static iomux_cfg_t usdhc2_sd[] = {
+ SC_P_USDHC2_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+ SC_P_USDHC2_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_WP | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+ SC_P_USDHC2_CD_B | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+void init_clk_usdhc(u32 index);
+int fsl_esdhc_initialize(struct bd_info *bis, struct fsl_esdhc_cfg *cfg);
+int arch_cpu_init(void);
+int board_early_init_f(void);
+int timer_init(void);
+void board_init_r(gd_t *id, ulong dest_addr);
+
+int board_mmc_init(struct bd_info *bis)
+{
+ int i, ret;
+
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-Boot device node) (Physical Port)
+ * mmc0 USDHC1
+ * mmc1 USDHC2
+ * mmc2 USDHC3
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ ret = sc_pm_set_resource_power_mode(-1, SC_R_SDHC_0, SC_PM_PW_MODE_ON);
+ if (ret != SC_ERR_NONE)
+ return ret;
+
+ imx8_iomux_setup_multiple_pads(emmc0, ARRAY_SIZE(emmc0));
+ init_clk_usdhc(0);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+ case 1:
+ ret = sc_pm_set_resource_power_mode(-1, SC_R_SDHC_2, SC_PM_PW_MODE_ON);
+ if (ret != SC_ERR_NONE)
+ return ret;
+ ret = sc_pm_set_resource_power_mode(-1, SC_R_GPIO_4, SC_PM_PW_MODE_ON);
+ if (ret != SC_ERR_NONE)
+ return ret;
+
+ imx8_iomux_setup_multiple_pads(usdhc2_sd, ARRAY_SIZE(usdhc2_sd));
+ init_clk_usdhc(2);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ gpio_request(USDHC2_CD_GPIO, "sd2_cd");
+ gpio_direction_input(USDHC2_CD_GPIO);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) than supported by the board\n", i + 1);
+ return 0;
+ }
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = 1;
+ break;
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ }
+
+ return ret;
+}
+
+#endif /* CONFIG_FSL_ESDHC_IMX */
+
+void spl_board_init(void)
+{
+#if defined(CONFIG_SPL_SPI_SUPPORT)
+ if (sc_rm_is_resource_owned(-1, SC_R_FSPI_0)) {
+ if (sc_pm_set_resource_power_mode(-1, SC_R_FSPI_0, SC_PM_PW_MODE_ON))
+ puts("Warning: failed to initialize FSPI0\n");
+ }
+#endif
+
+ puts("Normal Boot\n");
+}
+
+void spl_board_prepare_for_boot(void)
+{
+#if defined(CONFIG_SPL_SPI_SUPPORT)
+ if (sc_rm_is_resource_owned(-1, SC_R_FSPI_0)) {
+ if (sc_pm_set_resource_power_mode(-1, SC_R_FSPI_0, SC_PM_PW_MODE_OFF))
+ puts("Warning: failed to turn off FSPI0\n");
+ }
+#endif
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+ /* Just empty function now - can't decide what to choose */
+ debug("%s: %s\n", __func__, name);
+
+ return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+ /* Clear global data */
+ memset((void *)gd, 0, sizeof(gd_t));
+
+ arch_cpu_init();
+
+ board_early_init_f();
+
+ timer_init();
+
+ preloader_console_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ board_init_r(NULL, 0);
+}
diff --git a/common/Kconfig b/common/Kconfig
index a96842a5c1..894733a26e 100644
--- a/common/Kconfig
+++ b/common/Kconfig
@@ -528,7 +528,7 @@ config BOARD_TYPES
config DISPLAY_CPUINFO
bool "Display information about the CPU during start up"
- default y if ARC|| ARM || NIOS2 || X86 || XTENSA || M68K
+ default y if ARC || ARM || NIOS2 || X86 || XTENSA || M68K
help
Display information about the CPU that U-Boot is running on
when U-Boot starts up. The function print_cpuinfo() is called
diff --git a/configs/imx8qm_dmsse20a1_defconfig b/configs/imx8qm_dmsse20a1_defconfig
new file mode 100644
index 0000000000..569401cf56
--- /dev/null
+++ b/configs/imx8qm_dmsse20a1_defconfig
@@ -0,0 +1,105 @@
+CONFIG_ARM=y
+CONFIG_SPL_SYS_ICACHE_OFF=y
+CONFIG_SPL_SYS_DCACHE_OFF=y
+CONFIG_ARCH_IMX8=y
+CONFIG_SYS_TEXT_BASE=0x80020000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_LEN=0x2800000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_SYS_MMC_IMG_LOAD_PART=0
+CONFIG_TARGET_IMX8QM_DMSSE20_A1=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_DRIVERS_MISC=y
+CONFIG_ENV_OFFSET=0x80000
+CONFIG_SPL=y
+CONFIG_SYS_LOAD_ADDR=0x80280000
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_OF_CONTROL=y
+CONFIG_CI_UDC=y
+CONFIG_DM_PCA953X=y
+CONFIG_BOOTDELAY=3
+CONFIG_LOG=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_IMX_BOOTAUX=y
+CONFIG_FS_FAT=y
+CONFIG_FS_EXT4=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_IO_VOLTAGE=y
+CONFIG_MMC_UHS_SUPPORT=y
+CONFIG_MMC_HS400_SUPPORT=y
+CONFIG_MMC_BROKEN_CD=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FUSE=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx8qm-dmsse20-a1"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_IMX8=y
+CONFIG_CPU=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_FSL_ESDHC_IMX=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+# CONFIG_EFI_LOADER is not set
+CONFIG_FEC_MXC_SHARE_MDIO=y
+CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
+CONFIG_FEC_MXC=y
+CONFIG_FEC1_ENET_DEV=0
+CONFIG_ETHPRIME="eth0"
+CONFIG_FEC1_MXC_PHYADDR=0x4
+CONFIG_FEC2_ENET_DEV=1
+CONFIG_ETHPRIME1="eth1"
+CONFIG_FEC2_MXC_PHYADDR=0x4
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_IMX8=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8_POWER_DOMAIN=y
+CONFIG_IMX_SMMU=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_MISC=y
+CONFIG_SMC_FUSE=y
+CONFIG_BOOTAUX_RESERVED_MEM_BASE=0x88000000
+CONFIG_BOOTAUX_RESERVED_MEM_SIZE=0x08000000
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL_TINY_MEMSET=y
+CONFIG_AHAB_BOOT=y
+CONFIG_SYS_I2C_IMX_LPI2C=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_RV8803=y
+CONFIG_CMD_DATE=y
+# CONFIG_CMD_DEKBLOB is not set
diff --git a/doc/board/advantech/imx8qm-dmsse20-a1.rst b/doc/board/advantech/imx8qm-dmsse20-a1.rst
new file mode 100644
index 0000000000..bb116fa374
--- /dev/null
+++ b/doc/board/advantech/imx8qm-dmsse20-a1.rst
@@ -0,0 +1,59 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+NXP i.MX8QM DMSSE20-a1 board
+============================
+
+Quick Start
+-----------
+
+- Build the ARM Trusted firmware binary
+- Get scfw_tcm.bin and ahab-container.img
+- Get imx-mkimage
+- Build U-Boot
+- Flash the binary into the SD card
+- Boot
+
+Get and Build the ARM Trusted Firmware
+--------------------------------------
+
+.. code-block:: bash
+
+ $ git clone https://source.codeaurora.org/external/imx/imx-atf
+ $ cd imx-atf/
+ $ git checkout lf-5.10.72-2.2.0 -b lf-5.10.72-2.2.0
+ $ make PLAT=imx8qm bl31
+ $ cp build/imx8qm/release/bl31.bin $(builddir)
+
+Get scfw_tcm.bin and ahab-container.img
+---------------------------------------
+
+.. code-block:: bash
+
+ $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.11.0.bin
+ $ chmod +x imx-sc-firmware-1.11.0.bin
+ $ ./imx-sc-firmware-1.11.0.bin
+ $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-seco-3.8.5.bin
+ $ chmod +x imx-seco-3.8.5.bin
+ $ ./imx-seco-3.8.5.bin
+
+Or use this to avoid running random scripts from the internet,
+but note that you must agree to the license the script displays:
+
+.. code-block:: bash
+
+ $ dd if=imx-sc-firmware-1.11.0.bin of=imx-sc-firmware-1.11.0.tar.bz2 bs=42757 skip=1
+ $ tar -xf imx-sc-firmware-1.11.0.tar.bz2
+ $ cp imx-sc-firmware-1.11.0/mx8qm-val-scfw-tcm.bin $(builddir)
+ $ dd if=imx-seco-3.8.5.bin of=imx-seco-3.8.5.tar.bz2 bs=43978 skip=1
+ $ tar -xf imx-seco-3.8.5.tar.bz2
+ $ cp imx-seco-3.8.5/firmware/seco/mx8qmb0-ahab-container.img $(builddir)
+
+Build U-Boot
+------------
+.. code-block:: bash
+
+ $ export ATF_LOAD_ADDR=0x80000000
+ $ export BL33_LOAD_ADDR=0x80020000
+ $ make imx8qm_dmsse20a1_defconfig
+ $ make u-boot.bin
+ $ make flash.bin
diff --git a/doc/board/advantech/index.rst b/doc/board/advantech/index.rst
index e9b198c5c3..125b98c1f7 100644
--- a/doc/board/advantech/index.rst
+++ b/doc/board/advantech/index.rst
@@ -7,3 +7,4 @@ Advantech
:maxdepth: 2
imx8qm-rom7720-a1.rst
+ imx8qm-dmsse20-a1.rst
diff --git a/include/configs/imx8qm_dmsse20.h b/include/configs/imx8qm_dmsse20.h
new file mode 100644
index 0000000000..3050f79fa7
--- /dev/null
+++ b/include/configs/imx8qm_dmsse20.h
@@ -0,0 +1,164 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2017-2019 NXP
+ */
+
+#ifndef __IMX8QM_DMSSE20_H
+#define __IMX8QM_DMSSE20_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+#define CONFIG_REMAKE_ELF
+
+#define CONFIG_SPL_MAX_SIZE (124 * 1024)
+#define CONFIG_SPL_BSS_START_ADDR 0x00128000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */
+
+#define CONFIG_NR_DRAM_BANKS 4
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_BOARD_SETUP
+
+#undef CONFIG_BOOTM_NETBSD
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define USDHC1_BASE_ADDR 0x5B010000
+#define USDHC2_BASE_ADDR 0x5B020000
+#define USDHC3_BASE_ADDR 0x5B030000
+
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#define FEC_QUIRK_ENET_MAC
+
+#define CONFIG_PHY_GIGE /* Support for 1000BASE-X */
+
+#define IMX_FEC_BASE 0x5B040000
+/* FEC1 */
+#define IMX_FEC1_BASE 0x5B040000
+/* FEC2 */
+#define IMX_FEC2_BASE 0x5B050000
+
+#ifdef CONFIG_NAND_BOOT
+#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:128m(boot),32m(kernel),16m(dtb),8m(misc),-(rootfs) "
+#else
+#define MFG_NAND_PARTITION ""
+#endif
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=Image\0" \
+ "panel=NULL\0" \
+ "console=ttyLP0\0" \
+ "earlycon=lpuart32,0x5a060000\0" \
+ "fdt_addr=0x83000000\0" \
+ "boot_fdt=try\0" \
+ "fdt_file=imx8qm-dmsse20-a1.dtb\0" \
+ "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
+ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+ "mmcroot=/dev/mmcblk1p2 rootwait rw\0" \
+ "mmcautodetect=yes\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} earlycon=${earlycon},${baudrate} root=${mmcroot}\0 " \
+ "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "echo wait for boot; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} earlycon=${earlycon},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp mac=${ethaddr} nfsroot=${serverip}:${nfsroot},v3,tcp rw\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${loadaddr} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "booti; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else booti ${loadaddr} - ${fdt_addr}; fi"
+
+/* Link Definitions */
+
+#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
+
+/* Default environment is in SD */
+
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
+#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#else
+#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
+#endif
+
+#define CONFIG_SYS_MMC_ENV_DEV 2 /* USDHC3 */
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+#define CONFIG_SYS_SDRAM_BASE 0x080000000
+#define PHYS_SDRAM_1 0x080000000
+#define PHYS_SDRAM_2 0x880000000
+#define PHYS_SDRAM_1_SIZE 0x080000000 /* 2 GB */
+#define PHYS_SDRAM_2_SIZE 0x180000000 /* 6 GB */
+
+#define CONFIG_SYS_MEMTEST_START 0xA0000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (PHYS_SDRAM_1_SIZE >> 2))
+
+/* Serial */
+#define CONFIG_BAUDRATE 115200
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 8000000 /* 8MHz */
+
+/* MT35XU512ABA1G12 has only one Die, so QSPI0 B won't work */
+#ifdef CONFIG_FSL_FSPI
+#define CONFIG_SF_DEFAULT_BUS 0
+#define CONFIG_SF_DEFAULT_CS 0
+#define CONFIG_SF_DEFAULT_SPEED 40000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define FSL_FSPI_FLASH_SIZE SZ_64M
+#define FSL_FSPI_FLASH_NUM 1
+#define FSPI0_BASE_ADDR 0x5d120000
+#define FSPI0_AMBA_BASE 0
+#define CONFIG_SYS_FSL_FSPI_AHB
+#endif
+
+/* #define CONFIG_OF_SYSTEM_SETUP */
+
+#endif /* __IMX8QM_DMSSE20_H */
--
2.17.1
More information about the U-Boot
mailing list