[PATCH 2/3] configs: at91: sam9x60ek: enable QSPI and SF command

[Sergiu Moga]

Add the configurations required for enabling QSPI and the SF command
to allow changes to be made dynamically to serial flash devices from
the command line interface.

Signed-off-by: Sergiu Moga <sergiu.moga at microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus at microchip.com>
---
 configs/sam9x60ek_mmc_defconfig       | 13 +++++++++++++
 configs/sam9x60ek_nandflash_defconfig | 13 +++++++++++++
 2 files changed, 26 insertions(+)

diff --git a/configs/sam9x60ek_mmc_defconfig b/configs/sam9x60ek_mmc_defconfig
index bc0164c38e..cab469877a 100644
--- a/configs/sam9x60ek_mmc_defconfig
+++ b/configs/sam9x60ek_mmc_defconfig
@@ -33,6 +33,7 @@ CONFIG_CMD_DM=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_NAND=y
 CONFIG_CMD_NAND_TRIMFFS=y
 # CONFIG_CMD_SETEXPR is not set
@@ -63,6 +64,8 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ATMEL=y
 CONFIG_MTD=y
 CONFIG_MTD_RAW_NAND=y
+CONFIG_SF_DEFAULT_MODE=0x0
+CONFIG_SF_DEFAULT_SPEED=50000000
 CONFIG_NAND_ATMEL=y
 CONFIG_ATMEL_NAND_HW_PMECC=y
 CONFIG_PMECC_CAP=8
@@ -84,3 +87,13 @@ CONFIG_W1_GPIO=y
 CONFIG_W1_EEPROM=y
 CONFIG_W1_EEPROM_DS24XXX=y
 CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_ATMEL_QSPI=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_MTD=y
diff --git a/configs/sam9x60ek_nandflash_defconfig b/configs/sam9x60ek_nandflash_defconfig
index 5c34f089e6..7c1a473208 100644
--- a/configs/sam9x60ek_nandflash_defconfig
+++ b/configs/sam9x60ek_nandflash_defconfig
@@ -33,6 +33,7 @@ CONFIG_CMD_DM=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
+CONFIG_CMD_SF_TEST=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_NAND=y
 CONFIG_CMD_NAND_TRIMFFS=y
@@ -69,6 +70,15 @@ CONFIG_ATMEL_NAND_HW_PMECC=y
 CONFIG_PMECC_CAP=8
 CONFIG_SYS_NAND_ONFI_DETECTION=y
 CONFIG_PHY_MICREL=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SF_DEFAULT_BUS=0
+CONFIG_SF_DEFAULT_SPEED=50000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
 CONFIG_DM_ETH=y
 CONFIG_MACB=y
 CONFIG_PINCTRL=y
@@ -78,6 +88,9 @@ CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_ATMEL_USART=y
 CONFIG_SYSRESET=y
 CONFIG_SYSRESET_AT91=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_QSPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_W1=y
-- 
2.25.1