[PATCH 05/12] ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1
Andre Przywara
andre.przywara at arm.com
Fri May 20 17:34:02 CEST 2022
On Wed, 27 Apr 2022 15:31:24 -0500
Samuel Holland <samuel at sholland.org> wrote:
Hi,
> Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
> SoCs and all existing boards from the Linux v5.18-rc1 tag.
>
> These changes are combined into one commit due to interdependencies:
> - The unit addresses were removed from bitbanged I2C buses, which
> drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
> and sun6i-a31-colombus.dts.
> - The pinctrl nodes were renamed, including some used by the shared
> header sunxi-reference-design-tablet.dtsi.
>
> To maintain ABI compatibility with existing LTS kernels, one change
> moving some IP blocks to the r_intc interrupt controller is excluded.
> This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
>
> This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
> to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
>
> This commit also adds the following new board devicetrees:
> - sun5i-a13-licheepi-one.dts
> - sun5i-a13-pocketbook-touch-lux-3.dts
> - sun5i-gr8-evb.dts
> - sun8i-a23-ippo-q8h-v1.2.dts
> - sun8i-a23-ippo-q8h-v5.dts
> - sun8i-a33-et-q8-v1.6.dts
> - sun8i-a33-ippo-q8h-v1.2.dts
> - sun8i-r16-nintendo-super-nes-classic.dts
>
> As with the other SoCs, updates of note are conversion of GPIO pull-up
> from pinconf to GPIO flags and renaming the detection GPIO properties in
> the USB PHY nodes.
>
> Signed-off-by: Samuel Holland <samuel at sholland.org>
So that's a big one. The sync part looks good, I compared the files
against the kernel, and the r_intc change is the only difference.
Most of the changes are about node names and GPIO / pinctrl usage, which
*should* be fine, especially for U-Boot.
However there are a number of incompatible changes, I marked them below in
the patch, for reference, but enumerate them here for easier discussion:
- "allwinner,sun4i-a10-sram-controller" got replaced with
"allwinner,sun5i-a13-system-control", in sun5i-a13.dtsi. U-Boot doesn't
care, and the Linux driver interestingly doesn't make a difference. So not
sure why the new name wasn't just *added*. This would affect pre v4.19
kernels, only, so I wouldn't consider this a real problem.
- "urt,umsh-8596md-t", "simple-panel" was changed to
"bananapi,s070wv20-ct16", in sun5i-a13-q8-tablet.dts. I think U-Boot
shouldn't be affected, as panel usage is controlled via Kconfig.
For the kernel it seems to be v4.20 adding support.
- A23/A33 suffer from a change in the timer compatible string (in
sun8i-a23-a33.dtsi), requiring Linux v5.4 at least. I am not sure how
fatal this is, since we have the arch timer in those SoCs.
- More problematic seems to be the rtc compatible string change in
sun8i-a23-a33.dtsi, which restricts kernel compatibility to v5.0 and later.
I am not sure if that prevents the CCU and pinctrl to probe (because they
use the first rtc provided clock as one of their input clocks).
I wonder if having the old compatible string as a fallback is feasible: I
don't the second RTC clock used anywhere, and the RTC/clock driver doesn't
seem to make a difference between the two compatibles otherwise.
So overall this might look bad, but the breakages are:
a) only for those older generation of devices, which probably don't use
UEFI boot or otherwise rely on $fdtcontroladdr for the kernel, and
b) will probably work fine with kernel v5.4 onwards, which seems to be
reasonably old and well spread by now.
So for the sake of getting our DTs much closer to the kernel copy, I am
happy with this change.
Reviewed-by: Andre Przywara <andre.przywara at arm.com>
Cheers,
Andre
> ---
>
> arch/arm/dts/Makefile | 10 +-
> arch/arm/dts/axp22x.dtsi | 11 +-
> arch/arm/dts/sun5i-a10s-auxtek-t003.dts | 16 +-
> arch/arm/dts/sun5i-a10s-auxtek-t004.dts | 35 +-
> arch/arm/dts/sun5i-a10s-mk802.dts | 31 +-
> arch/arm/dts/sun5i-a10s-olinuxino-micro.dts | 68 +---
> arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts | 22 +-
> arch/arm/dts/sun5i-a10s-wobo-i5.dts | 34 +-
> arch/arm/dts/sun5i-a10s.dtsi | 30 +-
> arch/arm/dts/sun5i-a13-ampe-a76.dts | 2 +-
> .../dts/sun5i-a13-empire-electronix-d709.dts | 41 +--
> arch/arm/dts/sun5i-a13-hsg-h702.dts | 37 +-
> arch/arm/dts/sun5i-a13-inet-86vs.dts | 2 +-
> arch/arm/dts/sun5i-a13-licheepi-one.dts | 214 +++++++++++
> arch/arm/dts/sun5i-a13-olinuxino-micro.dts | 50 +--
> arch/arm/dts/sun5i-a13-olinuxino.dts | 56 +--
> .../dts/sun5i-a13-pocketbook-touch-lux-3.dts | 258 ++++++++++++++
> arch/arm/dts/sun5i-a13-q8-tablet.dts | 18 +-
> arch/arm/dts/sun5i-a13-utoo-p66.dts | 26 +-
> arch/arm/dts/sun5i-a13.dtsi | 23 +-
> arch/arm/dts/sun5i-gr8-chip-pro.dts | 38 +-
> arch/arm/dts/sun5i-gr8-evb.dts | 333 ++++++++++++++++++
> arch/arm/dts/sun5i-gr8.dtsi | 12 +-
> arch/arm/dts/sun5i-r8-chip.dts | 52 +--
> .../dts/sun5i-reference-design-tablet.dtsi | 57 +--
> arch/arm/dts/sun5i.dtsi | 209 +++++++----
> arch/arm/dts/sun6i-a31-app4-evb1.dts | 10 +-
> arch/arm/dts/sun6i-a31-colombus.dts | 57 +--
> arch/arm/dts/sun6i-a31-hummingbird.dts | 75 +---
> arch/arm/dts/sun6i-a31-i7.dts | 47 +--
> arch/arm/dts/sun6i-a31-m9.dts | 46 +--
> arch/arm/dts/sun6i-a31-mele-a1000g-quad.dts | 46 +--
> arch/arm/dts/sun6i-a31-mixtile-loftq.dts | 6 +-
> arch/arm/dts/sun6i-a31.dtsi | 218 +++++++-----
> arch/arm/dts/sun6i-a31s-colorfly-e708-q1.dts | 2 +-
> arch/arm/dts/sun6i-a31s-cs908.dts | 17 +-
> arch/arm/dts/sun6i-a31s-inet-q972.dts | 8 +-
> arch/arm/dts/sun6i-a31s-primo81.dts | 32 +-
> arch/arm/dts/sun6i-a31s-sina31s-core.dtsi | 4 +-
> arch/arm/dts/sun6i-a31s-sina31s.dts | 39 +-
> arch/arm/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 144 +++++---
> .../sun6i-a31s-yones-toptech-bs1078-v2.dts | 22 +-
> .../dts/sun6i-reference-design-tablet.dtsi | 22 +-
> arch/arm/dts/sun8i-a23-a33.dtsi | 308 ++++++++++++----
> arch/arm/dts/sun8i-a23-evb.dts | 20 +-
> arch/arm/dts/sun8i-a23-gt90h-v4.dts | 2 +-
> arch/arm/dts/sun8i-a23-ippo-q8h-v1.2.dts | 73 ++++
> arch/arm/dts/sun8i-a23-ippo-q8h-v5.dts | 73 ++++
> .../dts/sun8i-a23-polaroid-mid2407pxe03.dts | 15 +-
> .../dts/sun8i-a23-polaroid-mid2809pxe04.dts | 15 +-
> arch/arm/dts/sun8i-a23-q8-tablet.dts | 10 +
> arch/arm/dts/sun8i-a23.dtsi | 26 +-
> ...c-edition.dts => sun8i-a33-et-q8-v1.6.dts} | 32 +-
> arch/arm/dts/sun8i-a33-ga10h-v1.1.dts | 4 +-
> arch/arm/dts/sun8i-a33-inet-d978-rev2.dts | 14 +-
> arch/arm/dts/sun8i-a33-ippo-q8h-v1.2.dts | 57 +++
> arch/arm/dts/sun8i-a33-olinuxino.dts | 12 +-
> arch/arm/dts/sun8i-a33-q8-tablet.dts | 7 +
> arch/arm/dts/sun8i-a33-sinlinx-sina33.dts | 34 +-
> arch/arm/dts/sun8i-a33.dtsi | 270 +++++---------
> arch/arm/dts/sun8i-q8-common.dtsi | 31 +-
> arch/arm/dts/sun8i-r16-bananapi-m2m.dts | 55 ++-
> .../dts/sun8i-r16-nintendo-nes-classic.dts | 54 +++
> .../sun8i-r16-nintendo-super-nes-classic.dts | 11 +
> arch/arm/dts/sun8i-r16-parrot.dts | 62 +---
> .../dts/sun8i-reference-design-tablet.dtsi | 33 +-
> arch/arm/dts/sunxi-common-regulators.dtsi | 39 --
> .../dts/sunxi-reference-design-tablet.dtsi | 11 +-
> arch/arm/mach-sunxi/Kconfig | 2 +-
> .../Nintendo_NES_Classic_Edition_defconfig | 2 +-
> 70 files changed, 2149 insertions(+), 1603 deletions(-)
> create mode 100644 arch/arm/dts/sun5i-a13-licheepi-one.dts
> create mode 100644 arch/arm/dts/sun5i-a13-pocketbook-touch-lux-3.dts
> create mode 100644 arch/arm/dts/sun5i-gr8-evb.dts
> create mode 100644 arch/arm/dts/sun8i-a23-ippo-q8h-v1.2.dts
> create mode 100644 arch/arm/dts/sun8i-a23-ippo-q8h-v5.dts
> rename arch/arm/dts/{sun8i-r16-nintendo-nes-classic-edition.dts => sun8i-a33-et-q8-v1.6.dts} (81%)
> create mode 100644 arch/arm/dts/sun8i-a33-ippo-q8h-v1.2.dts
> create mode 100644 arch/arm/dts/sun8i-r16-nintendo-nes-classic.dts
> create mode 100644 arch/arm/dts/sun8i-r16-nintendo-super-nes-classic.dts
>
...
> diff --git a/arch/arm/dts/sun5i-a13-q8-tablet.dts b/arch/arm/dts/sun5i-a13-q8-tablet.dts
> index a89f29fa3e..f9fc1c8b60 100644
> --- a/arch/arm/dts/sun5i-a13-q8-tablet.dts
> +++ b/arch/arm/dts/sun5i-a13-q8-tablet.dts
> @@ -49,19 +49,13 @@
> compatible = "allwinner,q8-a13", "allwinner,sun5i-a13";
>
> panel: panel {
> - compatible = "urt,umsh-8596md-t", "simple-panel";
> - #address-cells = <1>;
> - #size-cells = <0>;
> + compatible = "bananapi,s070wv20-ct16";
This drops the "simple-panel" fallback compatible, and replaces it just a
device specific one. This means you need at least Linux v4.20 to use the
display.
> + power-supply = <®_vcc3v3>;
> + enable-gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; /* AXP GPIO0 */
> + backlight = <&backlight>;
>
> - port at 0 {
> - reg = <0>;
> - /* TODO: lcd panel uses axp gpio0 as enable pin */
> - backlight = <&backlight>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - panel_input: endpoint at 0 {
> - reg = <0>;
> + port {
> + panel_input: endpoint {
> remote-endpoint = <&tcon0_out_lcd>;
> };
> };
[ ... ]
> diff --git a/arch/arm/dts/sun5i.dtsi b/arch/arm/dts/sun5i.dtsi
> index 07f2248ed5..250d6b87ab 100644
> --- a/arch/arm/dts/sun5i.dtsi
> +++ b/arch/arm/dts/sun5i.dtsi
> @@ -42,14 +42,14 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> -#include "skeleton.dtsi"
> -
> #include <dt-bindings/clock/sun5i-ccu.h>
> #include <dt-bindings/dma/sun4i-a10.h>
> #include <dt-bindings/reset/sun5i-ccu.h>
>
> / {
> interrupt-parent = <&intc>;
> + #address-cells = <1>;
> + #size-cells = <1>;
>
> cpus {
> #address-cells = <1>;
> @@ -68,7 +68,7 @@
> #size-cells = <1>;
> ranges;
>
> - framebuffer at 0 {
> + framebuffer-lcd0 {
> compatible = "allwinner,simple-framebuffer",
> "simple-framebuffer";
> allwinner,pipeline = "de_be0-lcd0";
> @@ -77,7 +77,7 @@
> status = "disabled";
> };
>
> - framebuffer at 1 {
> + framebuffer-lcd0-tve0 {
> compatible = "allwinner,simple-framebuffer",
> "simple-framebuffer";
> allwinner,pipeline = "de_be0-lcd0-tve0";
> @@ -93,14 +93,14 @@
> #size-cells = <1>;
> ranges;
>
> - osc24M: clk at 1c20050 {
> + osc24M: clk-24M {
> #clock-cells = <0>;
> compatible = "fixed-clock";
> clock-frequency = <24000000>;
> clock-output-names = "osc24M";
> };
>
> - osc32k: clk at 0 {
> + osc32k: clk-32k {
> #clock-cells = <0>;
> compatible = "fixed-clock";
> clock-frequency = <32768>;
> @@ -108,14 +108,30 @@
> };
> };
>
> - soc at 1c00000 {
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + /* Address must be kept in the lower 256 MiBs of DRAM for VE. */
> + default-pool {
> + compatible = "shared-dma-pool";
> + size = <0x6000000>;
> + alloc-ranges = <0x40000000 0x10000000>;
> + reusable;
> + linux,cma-default;
> + };
> + };
> +
> + soc {
> compatible = "simple-bus";
> #address-cells = <1>;
> #size-cells = <1>;
> + dma-ranges;
> ranges;
>
> - sram-controller at 1c00000 {
> - compatible = "allwinner,sun4i-a10-sram-controller";
> + system-control at 1c00000 {
> + compatible = "allwinner,sun5i-a13-system-control";
This is a change in the compatible string. Linux kernels before v4.19 won't
have a driver matching this new string, so will fail to use that device.
This would affect USB OTG and EMAC operation.
> reg = <0x01c00000 0x30>;
> #address-cells = <1>;
> #size-cells = <1>;
> @@ -127,12 +143,13 @@
> #address-cells = <1>;
> #size-cells = <1>;
> ranges = <0 0x00000000 0xc000>;
> - };
>
> - emac_sram: sram-section at 8000 {
> - compatible = "allwinner,sun4i-a10-sram-a3-a4";
> - reg = <0x8000 0x4000>;
> - status = "disabled";
> + emac_sram: sram-section at 8000 {
> + compatible = "allwinner,sun5i-a13-sram-a3-a4",
> + "allwinner,sun4i-a10-sram-a3-a4";
> + reg = <0x8000 0x4000>;
> + status = "disabled";
> + };
> };
>
> sram_d: sram at 10000 {
[ ... ]
> diff --git a/arch/arm/dts/sun8i-a23-a33.dtsi b/arch/arm/dts/sun8i-a23-a33.dtsi
> index 44f3cad3de..a42fac676b 100644
> --- a/arch/arm/dts/sun8i-a23-a33.dtsi
> +++ b/arch/arm/dts/sun8i-a23-a33.dtsi
> @@ -42,8 +42,6 @@
> * OTHER DEALINGS IN THE SOFTWARE.
> */
>
> -#include "skeleton.dtsi"
> -
> #include <dt-bindings/interrupt-controller/arm-gic.h>
>
> #include <dt-bindings/clock/sun8i-a23-a33-ccu.h>
> @@ -51,13 +49,15 @@
>
> / {
> interrupt-parent = <&gic>;
> + #address-cells = <1>;
> + #size-cells = <1>;
>
> chosen {
> #address-cells = <1>;
> #size-cells = <1>;
> ranges;
>
> - simplefb_lcd: framebuffer at 0 {
> + simplefb_lcd: framebuffer-lcd0 {
> compatible = "allwinner,simple-framebuffer",
> "simple-framebuffer";
> allwinner,pipeline = "de_be0-lcd0";
> @@ -68,6 +68,12 @@
> };
> };
>
> + de: display-engine {
> + /* compatible gets set in SoC specific dtsi file */
> + allwinner,pipelines = <&fe0>;
> + status = "disabled";
> + };
> +
> timer {
> compatible = "arm,armv7-timer";
> interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> @@ -118,12 +124,34 @@
> };
> };
>
> - soc at 1c00000 {
> + soc {
> compatible = "simple-bus";
> #address-cells = <1>;
> #size-cells = <1>;
> ranges;
>
> + system-control at 1c00000 {
> + compatible = "allwinner,sun8i-a23-system-control";
> + reg = <0x01c00000 0x30>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + sram_c: sram at 1d00000 {
> + compatible = "mmio-sram";
> + reg = <0x01d00000 0x80000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x01d00000 0x80000>;
> +
> + ve_sram: sram-section at 0 {
> + compatible = "allwinner,sun8i-a23-sram-c1",
> + "allwinner,sun4i-a10-sram-c1";
> + reg = <0x000000 0x80000>;
> + };
> + };
> + };
> +
> dma: dma-controller at 1c02000 {
> compatible = "allwinner,sun8i-a23-dma";
> reg = <0x01c02000 0x1000>;
> @@ -133,6 +161,60 @@
> #dma-cells = <1>;
> };
>
> + nfc: nand-controller at 1c03000 {
> + compatible = "allwinner,sun8i-a23-nand-controller";
> + reg = <0x01c03000 0x1000>;
> + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
> + clock-names = "ahb", "mod";
> + resets = <&ccu RST_BUS_NAND>;
> + reset-names = "ahb";
> + dmas = <&dma 5>;
> + dma-names = "rxtx";
> + pinctrl-names = "default";
> + pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + tcon0: lcd-controller at 1c0c000 {
> + /* compatible gets set in SoC specific dtsi file */
> + reg = <0x01c0c000 0x1000>;
> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&dma 12>;
> + clocks = <&ccu CLK_BUS_LCD>,
> + <&ccu CLK_LCD_CH0>,
> + <&ccu 13>;
> + clock-names = "ahb",
> + "tcon-ch0",
> + "lvds-alt";
> + clock-output-names = "tcon-pixel-clock";
> + #clock-cells = <0>;
> + resets = <&ccu RST_BUS_LCD>,
> + <&ccu RST_BUS_LVDS>;
> + reset-names = "lcd",
> + "lvds";
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + tcon0_in: port at 0 {
> + reg = <0>;
> +
> + tcon0_in_drc0: endpoint {
> + remote-endpoint = <&drc0_out_tcon0>;
> + };
> + };
> +
> + tcon0_out: port at 1 {
> + reg = <1>;
> + };
> + };
> + };
> +
> mmc0: mmc at 1c0f000 {
> compatible = "allwinner,sun7i-a20-mmc";
> reg = <0x01c0f000 0x1000>;
> @@ -147,6 +229,8 @@
> resets = <&ccu RST_BUS_MMC0>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -190,21 +274,6 @@
> #size-cells = <0>;
> };
>
> - nfc: nand at 1c03000 {
> - compatible = "allwinner,sun4i-a10-nand";
> - reg = <0x01c03000 0x1000>;
> - interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
> - clock-names = "ahb", "mod";
> - resets = <&ccu RST_BUS_NAND>;
> - reset-names = "ahb";
> - pinctrl-names = "default";
> - pinctrl-0 = <&nand_pins &nand_pins_cs0 &nand_pins_rb0>;
> - status = "disabled";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> usb_otg: usb at 1c19000 {
> /* compatible gets set in SoC specific dtsi file */
> reg = <0x01c19000 0x0400>;
> @@ -215,6 +284,7 @@
> phys = <&usbphy 0>;
> phy-names = "usb";
> extcon = <&usbphy 0>;
> + dr_mode = "otg";
> status = "disabled";
> };
>
> @@ -276,22 +346,30 @@
> #interrupt-cells = <3>;
> #gpio-cells = <3>;
>
> - uart0_pins_a: uart0 at 0 {
> - pins = "PF2", "PF4";
> - function = "uart0";
> + i2c0_pins: i2c0-pins {
> + pins = "PH2", "PH3";
> + function = "i2c0";
> };
>
> - uart1_pins_a: uart1 at 0 {
> - pins = "PG6", "PG7";
> - function = "uart1";
> + i2c1_pins: i2c1-pins {
> + pins = "PH4", "PH5";
> + function = "i2c1";
> };
>
> - uart1_pins_cts_rts_a: uart1-cts-rts at 0 {
> - pins = "PG8", "PG9";
> - function = "uart1";
> + i2c2_pins: i2c2-pins {
> + pins = "PE12", "PE13";
> + function = "i2c2";
> };
>
> - mmc0_pins_a: mmc0 at 0 {
> + lcd_rgb666_pins: lcd-rgb666-pins {
> + pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
> + "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
> + "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
> + "PD24", "PD25", "PD26", "PD27";
> + function = "lcd0";
> + };
> +
> + mmc0_pins: mmc0-pins {
> pins = "PF0", "PF1", "PF2",
> "PF3", "PF4", "PF5";
> function = "mmc0";
> @@ -299,7 +377,7 @@
> bias-pull-up;
> };
>
> - mmc1_pins_a: mmc1 at 0 {
> + mmc1_pg_pins: mmc1-pg-pins {
> pins = "PG0", "PG1", "PG2",
> "PG3", "PG4", "PG5";
> function = "mmc1";
> @@ -307,7 +385,7 @@
> bias-pull-up;
> };
>
> - mmc2_8bit_pins: mmc2_8bit {
> + mmc2_8bit_pins: mmc2-8bit-pins {
> pins = "PC5", "PC6", "PC8",
> "PC9", "PC10", "PC11",
> "PC12", "PC13", "PC14",
> @@ -324,61 +402,53 @@
> function = "nand0";
> };
>
> - nand_pins_cs0: nand-pins-cs0 {
> + nand_cs0_pin: nand-cs0-pin {
> pins = "PC4";
> function = "nand0";
> bias-pull-up;
> };
>
> - nand_pins_cs1: nand-pins-cs1 {
> + nand_cs1_pin: nand-cs1-pin {
> pins = "PC3";
> function = "nand0";
> bias-pull-up;
> };
>
> - nand_pins_rb0: nand-pins-rb0 {
> + nand_rb0_pin: nand-rb0-pin {
> pins = "PC6";
> function = "nand0";
> bias-pull-up;
> };
>
> - nand_pins_rb1: nand-pins-rb1 {
> + nand_rb1_pin: nand-rb1-pin {
> pins = "PC7";
> function = "nand0";
> bias-pull-up;
> };
>
> - pwm0_pins: pwm0 {
> + pwm0_pin: pwm0-pin {
> pins = "PH0";
> function = "pwm0";
> };
>
> - i2c0_pins_a: i2c0 at 0 {
> - pins = "PH2", "PH3";
> - function = "i2c0";
> - };
> -
> - i2c1_pins_a: i2c1 at 0 {
> - pins = "PH4", "PH5";
> - function = "i2c1";
> + uart0_pf_pins: uart0-pf-pins {
> + pins = "PF2", "PF4";
> + function = "uart0";
> };
>
> - i2c2_pins_a: i2c2 at 0 {
> - pins = "PE12", "PE13";
> - function = "i2c2";
> + uart1_pg_pins: uart1-pg-pins {
> + pins = "PG6", "PG7";
> + function = "uart1";
> };
>
> - lcd_rgb666_pins: lcd-rgb666 at 0 {
> - pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
> - "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
> - "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
> - "PD24", "PD25", "PD26", "PD27";
> - function = "lcd0";
> + uart1_cts_rts_pg_pins: uart1-cts-rts-pg-pins {
> + pins = "PG8", "PG9";
> + function = "uart1";
> };
> };
>
> timer at 1c20c00 {
> - compatible = "allwinner,sun4i-a10-timer";
> + compatible = "allwinner,sun8i-a23-timer";
This changes the compatible string, which only started to be supported
with Linux v5.4. Any older kernel would not be able to use that timer, but
with the arch timer stepping up, we don't lose too much, I guess?
> reg = <0x01c20c00 0xa0>;
> interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> @@ -389,6 +459,7 @@
> compatible = "allwinner,sun6i-a31-wdt";
> reg = <0x01c20ca0 0x20>;
> interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&osc24M>;
> };
>
> pwm: pwm at 1c21400 {
> @@ -477,6 +548,8 @@
> interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C0>;
> resets = <&ccu RST_BUS_I2C0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -488,6 +561,8 @@
> interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C1>;
> resets = <&ccu RST_BUS_I2C1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -499,6 +574,8 @@
> interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_I2C2>;
> resets = <&ccu RST_BUS_I2C2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -532,7 +609,7 @@
> };
>
> gic: interrupt-controller at 1c81000 {
> - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + compatible = "arm,gic-400";
> reg = <0x01c81000 0x1000>,
> <0x01c82000 0x2000>,
> <0x01c84000 0x2000>,
> @@ -542,17 +619,104 @@
> interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> };
>
> + fe0: display-frontend at 1e00000 {
> + /* compatible gets set in SoC specific dtsi file */
> + reg = <0x01e00000 0x20000>;
> + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
> + <&ccu CLK_DRAM_DE_FE>;
> + clock-names = "ahb", "mod",
> + "ram";
> + resets = <&ccu RST_BUS_DE_FE>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + fe0_out: port at 1 {
> + reg = <1>;
> +
> + fe0_out_be0: endpoint {
> + remote-endpoint = <&be0_in_fe0>;
> + };
> + };
> + };
> + };
> +
> + be0: display-backend at 1e60000 {
> + /* compatible gets set in SoC specific dtsi file */
> + reg = <0x01e60000 0x10000>;
> + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
> + <&ccu CLK_DRAM_DE_BE>;
> + clock-names = "ahb", "mod",
> + "ram";
> + resets = <&ccu RST_BUS_DE_BE>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + be0_in: port at 0 {
> + reg = <0>;
> +
> + be0_in_fe0: endpoint {
> + remote-endpoint = <&fe0_out_be0>;
> + };
> + };
> +
> + be0_out: port at 1 {
> + reg = <1>;
> +
> + be0_out_drc0: endpoint {
> + remote-endpoint = <&drc0_in_be0>;
> + };
> + };
> + };
> + };
> +
> + drc0: drc at 1e70000 {
> + /* compatible gets set in SoC specific dtsi file */
> + reg = <0x01e70000 0x10000>;
> + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
> + <&ccu CLK_DRAM_DRC>;
> + clock-names = "ahb", "mod", "ram";
> + resets = <&ccu RST_BUS_DRC>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + drc0_in: port at 0 {
> + reg = <0>;
> +
> + drc0_in_be0: endpoint {
> + remote-endpoint = <&be0_out_drc0>;
> + };
> + };
> +
> + drc0_out: port at 1 {
> + reg = <1>;
> +
> + drc0_out_tcon0: endpoint {
> + remote-endpoint = <&tcon0_in_drc0>;
> + };
> + };
> + };
> + };
> +
> rtc: rtc at 1f00000 {
> - compatible = "allwinner,sun6i-a31-rtc";
> - reg = <0x01f00000 0x54>;
> + compatible = "allwinner,sun8i-a23-rtc";
This changes the compatible string, requiring a Linux v5.0 kernel or later
to work. While we can probably get over the loss of the actual real-time
clock, it is also a clock provider, and the provided clock is used by the
CCU and pinctrl drivers.
> + reg = <0x01f00000 0x400>;
> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> - clock-output-names = "osc32k";
> + clock-output-names = "osc32k", "osc32k-out";
> clocks = <&ext_osc32k>;
> #clock-cells = <1>;
> };
>
> - nmi_intc: interrupt-controller at 1f00c00 {
> + r_intc: interrupt-controller at 1f00c00 {
> compatible = "allwinner,sun6i-a31-r-intc";
> interrupt-controller;
> #interrupt-cells = <2>;
> @@ -624,6 +788,20 @@
> status = "disabled";
> };
>
> + r_i2c: i2c at 1f02400 {
> + compatible = "allwinner,sun8i-a23-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x01f02400 0x400>;
> + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&r_i2c_pins>;
> + clocks = <&apb0_gates 6>;
> + resets = <&apb0_rst 6>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> r_pio: pinctrl at 1f02c00 {
> compatible = "allwinner,sun8i-a23-r-pinctrl";
> reg = <0x01f02c00 0x400>;
> @@ -634,18 +812,22 @@
> gpio-controller;
> interrupt-controller;
> #interrupt-cells = <3>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> #gpio-cells = <3>;
>
> - r_rsb_pins: r_rsb {
> + r_i2c_pins: r-i2c-pins {
> + pins = "PL0", "PL1";
> + function = "s_i2c";
> + bias-pull-up;
> + };
> +
> + r_rsb_pins: r-rsb-pins {
> pins = "PL0", "PL1";
> function = "s_rsb";
> drive-strength = <20>;
> bias-pull-up;
> };
>
> - r_uart_pins_a: r_uart at 0 {
> + r_uart_pins_a: r-uart-pins {
> pins = "PL2", "PL3";
> function = "s_uart";
> };
More information about the U-Boot
mailing list