[PATCH v2] configs: Transpeed 8K618-T: Add Transpeed 8K618-T board support

[Andre Przywara]

On Thu, 18 Jan 2024 17:56:55 +0000
Andre Przywara <andre.przywara at arm.com> wrote:

> On Thu, 18 Jan 2024 11:45:08 -0500
> Nick Alilovic <nickalilovic at gmail.com> wrote:
> 
> Hi Nick,
> 
> > This is a Chinese TV box based on Allwinner H618 SoC.
> > 
> > The DRAM parameters were derived from the values found in a firmware update.
> > 
> > Signed-off-by: Nick Alilovic <nickalilovic at gmail.com>  
> 
> Thanks for the fixes, looks good now:
> 
> Reviewed-by: Andre Przywara <andre.przywara at arm.com>
> 
> I will queue this after the DT files have been merged.

Merged into sunxi/master.

Thanks!
Andre

> > ---
> > This defconfig relies on the synced sun50i-h618-transpeed-8k618-t.dts file.
> > 
> >  configs/transpeed-8k618-t_defconfig | 27 +++++++++++++++++++++++++++
> >  1 file changed, 27 insertions(+)
> >  create mode 100644 configs/transpeed-8k618-t_defconfig
> > 
> > diff --git a/configs/transpeed-8k618-t_defconfig b/configs/transpeed-8k618-t_defconfig
> > new file mode 100644
> > index 0000000000..020d3974af
> > --- /dev/null
> > +++ b/configs/transpeed-8k618-t_defconfig
> > @@ -0,0 +1,27 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_SUNXI=y
> > +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-transpeed-8k618-t"
> > +CONFIG_SPL=y
> > +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x03030303
> > +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e
> > +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x1f12
> > +CONFIG_DRAM_SUN50I_H616_TPR0=0xc0001002
> > +CONFIG_DRAM_SUN50I_H616_TPR10=0x2f1107
> > +CONFIG_DRAM_SUN50I_H616_TPR11=0xddddcccc
> > +CONFIG_DRAM_SUN50I_H616_TPR12=0xeddc7665
> > +CONFIG_MACH_SUN50I_H616=y
> > +CONFIG_SUNXI_DRAM_H616_DDR3_1333=y
> > +CONFIG_DRAM_CLK=648
> > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > +CONFIG_R_I2C_ENABLE=y
> > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > +CONFIG_SPL_I2C=y
> > +CONFIG_SPL_SYS_I2C_LEGACY=y
> > +CONFIG_SYS_I2C_MVTWSI=y
> > +CONFIG_SYS_I2C_SLAVE=0x7f
> > +CONFIG_SYS_I2C_SPEED=400000
> > +CONFIG_SUPPORT_EMMC_BOOT=y
> > +CONFIG_AXP313_POWER=y
> > +CONFIG_AXP_DCDC3_VOLT=1360
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_USB_OHCI_HCD=y  
> 
>