[PATCH v3 4/9] usb: dwc3-generic: Add STih407 support
Patrice CHOTARD
patrice.chotard at foss.st.com
Thu Jan 23 15:40:18 CET 2025
On 1/22/25 10:02, Mattijs Korpershoek wrote:
> Hi Patrice,
>
> Thank you for the patch.
>
> On lun., janv. 20, 2025 at 09:01, Patrice Chotard <patrice.chotard at foss.st.com> wrote:
>
>> Add STi glue logic to manage the DWC3 HC on STiH407
>> SoC family. It configures the internal glue logic and
>> syscfg registers.
>>
>> Signed-off-by: Patrice Chotard <patrice.chotard at foss.st.com>
>> Cc: Marek Vasut <marex at denx.de>
>>
>> ---
>>
>> Changes in v3:
>> - Replace debug() by dev_err()
>> - check return value of syscon_regmap_lookup_by_phandle()
>>
>> Changes in v2:
>> - add dwc3-sti.c DWC3 wrapper as done for dwc3-am62.c
>>
>> MAINTAINERS | 1 +
>> drivers/usb/dwc3/Kconfig | 6 ++
>> drivers/usb/dwc3/Makefile | 1 +
>> drivers/usb/dwc3/dwc3-generic-sti.c | 132 ++++++++++++++++++++++++++++
>> 4 files changed, 140 insertions(+)
>> create mode 100644 drivers/usb/dwc3/dwc3-generic-sti.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 8c6c0c2a4bc..5d7e251e601 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -656,6 +656,7 @@ F: drivers/mmc/sti_sdhci.c
>> F: drivers/reset/sti-reset.c
>> F: drivers/serial/serial_sti_asc.c
>> F: drivers/sysreset/sysreset_sti.c
>> +F: drivers/usb/host/dwc3-sti.c
>> F: drivers/timer/arm_global_timer.c
>> F: drivers/usb/host/dwc3-sti-glue.c
>> F: include/dwc3-sti-glue.h
>> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
>> index 0100723a68b..7d58ae65fb6 100644
>> --- a/drivers/usb/dwc3/Kconfig
>> +++ b/drivers/usb/dwc3/Kconfig
>> @@ -87,6 +87,12 @@ config USB_DWC3_LAYERSCAPE
>> Host and Peripheral operation modes are supported. OTG is not
>> supported.
>>
>> +config USB_DWC3_STI
>> + bool "STi USB wrapper"
>> + depends on DM_USB && USB_DWC3_GENERIC && SYSCON
>> + help
>> + Select this for STi Platforms.
>
> The improvements done in v3 based on the comments from v2 look good to me.
> However, checkpatch seems unhappy about this:
>
> $ ./scripts/checkpatch.pl --git --u-boot --git master..HEAD
>
> --------------------------------------------------------------
> Commit 2a4d2432f669 ("usb: dwc3-generic: Add STih407 support")
> --------------------------------------------------------------
> WARNING: please write a paragraph that describes the config symbol fully
> #42: FILE: drivers/usb/dwc3/Kconfig:90:
> +config USB_DWC3_STI
>
> Can't we reuse the help description from 'config USB_XHCI_STI' ?
> I'm sorry I missed this before.
Ah yes, will update it
Patrice
>
> With that addressed, please add:
>
> Reviewed-by: Mattijs Korpershoek <mkorpershoek at baylibre.com>
>
>> +
>> menu "PHY Subsystem"
>>
>> config USB_DWC3_PHY_OMAP
>> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
>> index a085c9d4628..985206eafe4 100644
>> --- a/drivers/usb/dwc3/Makefile
>> +++ b/drivers/usb/dwc3/Makefile
>> @@ -15,3 +15,4 @@ obj-$(CONFIG_USB_DWC3_UNIPHIER) += dwc3-uniphier.o
>> obj-$(CONFIG_USB_DWC3_LAYERSCAPE) += dwc3-layerscape.o
>> obj-$(CONFIG_USB_DWC3_PHY_OMAP) += ti_usb_phy.o
>> obj-$(CONFIG_USB_DWC3_PHY_SAMSUNG) += samsung_usb_phy.o
>> +obj-$(CONFIG_USB_DWC3_STI) += dwc3-generic-sti.o
>> diff --git a/drivers/usb/dwc3/dwc3-generic-sti.c b/drivers/usb/dwc3/dwc3-generic-sti.c
>> new file mode 100644
>> index 00000000000..2ff640cede4
>> --- /dev/null
>> +++ b/drivers/usb/dwc3/dwc3-generic-sti.c
>> @@ -0,0 +1,132 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-3-Clause
>> +/*
>> + * STi specific glue layer for DWC3
>> + *
>> + * Copyright (C) 2025, STMicroelectronics - All Rights Reserved
>> + */
>> +
>> +#include <reset.h>
>> +#include <regmap.h>
>> +#include <syscon.h>
>> +#include <asm/io.h>
>> +#include <dm/device.h>
>> +#include <dm/device_compat.h>
>> +#include <dm/read.h>
>> +#include <linux/usb/otg.h>
>> +#include "dwc3-generic.h"
>> +
>> +/* glue registers */
>> +#define CLKRST_CTRL 0x00
>> +#define AUX_CLK_EN BIT(0)
>> +#define SW_PIPEW_RESET_N BIT(4)
>> +#define EXT_CFG_RESET_N BIT(8)
>> +
>> +#define XHCI_REVISION BIT(12)
>> +
>> +#define USB2_VBUS_MNGMNT_SEL1 0x2C
>> +#define USB2_VBUS_UTMIOTG 0x1
>> +
>> +#define SEL_OVERRIDE_VBUSVALID(n) ((n) << 0)
>> +#define SEL_OVERRIDE_POWERPRESENT(n) ((n) << 4)
>> +#define SEL_OVERRIDE_BVALID(n) ((n) << 8)
>> +
>> +/* Static DRD configuration */
>> +#define USB3_CONTROL_MASK 0xf77
>> +
>> +#define USB3_DEVICE_NOT_HOST BIT(0)
>> +#define USB3_FORCE_VBUSVALID BIT(1)
>> +#define USB3_DELAY_VBUSVALID BIT(2)
>> +#define USB3_SEL_FORCE_OPMODE BIT(4)
>> +#define USB3_FORCE_OPMODE(n) ((n) << 5)
>> +#define USB3_SEL_FORCE_DPPULLDOWN2 BIT(8)
>> +#define USB3_FORCE_DPPULLDOWN2 BIT(9)
>> +#define USB3_SEL_FORCE_DMPULLDOWN2 BIT(10)
>> +#define USB3_FORCE_DMPULLDOWN2 BIT(11)
>> +
>> +static void dwc3_stih407_glue_configure(struct udevice *dev, int index,
>> + enum usb_dr_mode mode)
>> +{
>> + struct dwc3_glue_data *glue = dev_get_plat(dev);
>> + struct regmap *regmap;
>> + ulong syscfg_base;
>> + ulong syscfg_offset;
>> + ulong glue_base;
>> + int ret;
>> +
>> + /* deassert both powerdown and softreset */
>> + ret = reset_deassert_bulk(&glue->resets);
>> + if (ret) {
>> + dev_err(dev, "reset_deassert_bulk error: %d\n", ret);
>> + return;
>> + }
>> +
>> + regmap = syscon_regmap_lookup_by_phandle(dev, "st,syscfg");
>> + if (IS_ERR(regmap)) {
>> + dev_err(dev, "unable to get st,syscfg, dev %s\n", dev->name);
>> + return;
>> + }
>> +
>> + syscfg_base = regmap->ranges[0].start;
>> + glue_base = dev_read_addr_index(dev, 0);
>> + syscfg_offset = dev_read_addr_index(dev, 1);
>> +
>> + clrbits_le32(syscfg_base + syscfg_offset, USB3_CONTROL_MASK);
>> +
>> + /* glue drd init */
>> + switch (mode) {
>> + case USB_DR_MODE_PERIPHERAL:
>> + clrbits_le32(syscfg_base + syscfg_offset,
>> + USB3_DELAY_VBUSVALID | USB3_SEL_FORCE_OPMODE |
>> + USB3_FORCE_OPMODE(0x3) | USB3_SEL_FORCE_DPPULLDOWN2 |
>> + USB3_FORCE_DPPULLDOWN2 | USB3_SEL_FORCE_DMPULLDOWN2 |
>> + USB3_FORCE_DMPULLDOWN2);
>> +
>> + setbits_le32(syscfg_base + syscfg_offset,
>> + USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID);
>> + break;
>> +
>> + case USB_DR_MODE_HOST:
>> + clrbits_le32(syscfg_base + syscfg_offset,
>> + USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID |
>> + USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3) |
>> + USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2 |
>> + USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
>> +
>> + setbits_le32(syscfg_base + syscfg_offset, USB3_DELAY_VBUSVALID);
>> + break;
>> +
>> + default:
>> + dev_err(dev, "Unsupported mode of operation %d\n", mode);
>> + return;
>> + }
>> +
>> + /* glue init */
>> + setbits_le32(glue_base + CLKRST_CTRL, AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION);
>> + clrbits_le32(glue_base + CLKRST_CTRL, SW_PIPEW_RESET_N);
>> +
>> + /* configure mux for vbus, powerpresent and bvalid signals */
>> + setbits_le32(glue_base + USB2_VBUS_MNGMNT_SEL1,
>> + SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
>> + SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
>> + SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG));
>> + setbits_le32(glue_base + CLKRST_CTRL, SW_PIPEW_RESET_N);
>> +};
>> +
>> +struct dwc3_glue_ops stih407_ops = {
>> + .glue_configure = dwc3_stih407_glue_configure,
>> +};
>> +
>> +static const struct udevice_id dwc3_sti_match[] = {
>> + { .compatible = "st,stih407-dwc3", .data = (ulong)&stih407_ops},
>> + { /* sentinel */ }
>> +};
>> +
>> +U_BOOT_DRIVER(dwc3_sti_wrapper) = {
>> + .name = "dwc3-sti",
>> + .id = UCLASS_SIMPLE_BUS,
>> + .of_match = dwc3_sti_match,
>> + .bind = dwc3_glue_bind,
>> + .probe = dwc3_glue_probe,
>> + .remove = dwc3_glue_remove,
>> + .plat_auto = sizeof(struct dwc3_glue_data),
>> +};
>> --
>> 2.25.1
More information about the U-Boot
mailing list