[U-Boot] [PATCH V8] mcx: support for HTKW mcx board
Stefano Babic
sbabic at denx.de
Wed Feb 8 10:30:22 CET 2012
From: Ilya Yanok <yanok at emcraft.com>
This patch adds support for the HTKW mcx AM3517-based board.
Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both
NAND and MMC SPLs are supported.
Signed-off-by: Ilya Yanok <yanok at emcraft.com>
Signed-off-by: Stefano Babic <sbabic at denx.de>
CC: Tom Rini <tom.rini at gmail.com>
Cc: Detlev Zundel <dzu at denx.de>
---
Changes since V7:
- do not use temporary variable to return values (Igor Grinberg)
- port 2 is TTL, cannot be PHY (Igor Grinberg)
Changes from V6:
- rebased on current u-boot-ti
- applied and tested on top of EHCI Gavindraj's patches
- uses ULPI framework
Changes from V5
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/120254
- added comments on CONFIG_SYS_TEXT_BASE and SPL_{MALLOC,BSS}
Changes from V4
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/120148
- board_mmc_init return value fixed
- machine id added locally
- CONFIG_SYS_NAND_U_BOOT_SIZE removed
Changes from V3
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/118530
- Comment for misc_init_r function fixed
- Added check for gpio_request return value.
- Removed #if defined(CONFIG_GENERIC_MMC) around board_mmc_init
- CONFIG_USE_IRQ and related stuff removed from config
- CONFIG_OMAP3_MICRON_DDR removed
- CONFIG_SYS_MAXRAGS changed 32 -> 16
- Incorrect multiline comments (/*--- ones) fixed
- CONFIG_SPL_MAX_SIZE rewritten 0xB400 -> (45 << 10)
- CONFIG_SPL_NAND_WORKSPACE removed
Changes from V2
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/116548
- None
Changes from V1
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/115026
- Calls to gpio_set_value after gpio_direction_output removed
- Minor style problem (tab instead of space) fixed
SPL series:
Changes from V1
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112892
- OMAP EHCI support enabled in config
- MMC SPL support enabled in config
"DaVinci EMAC and HTKW mcx support" series:
Changes from V3
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112884
- NAND SPL support enabled in config
Changes from V2
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112317
- removed dead code from board/htkw/mcx/Makefile as Mike suggested
- removed EMAC reset (now done in generic cpu_eth_init())
- removed some unsuned defines from configuration header
Changes from V1
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/111197
- various style fixes to make checkpatch (almost) happy
- FSF address removed from GPL comments
- CONFIG_SYS_TEXT_BASE moved to configuration header, config.mk droped
- CONFIG_MACH_TYPE is used instead of setting mach type from board code
- i2c_init removed from misc_init_r
- cpu_eth_init removed (added to generic place by another patch)
- CONTROL_PADCONF defines removed
- Fixed boolean config options not to have a value
- CONFIG_MUSB_* and related defines removed
MAINTAINERS | 4 +
board/htkw/mcx/Makefile | 38 +++++
board/htkw/mcx/mcx.c | 112 +++++++++++++
board/htkw/mcx/mcx.h | 408 +++++++++++++++++++++++++++++++++++++++++++++++
boards.cfg | 1 +
include/configs/mcx.h | 378 +++++++++++++++++++++++++++++++++++++++++++
6 files changed, 941 insertions(+), 0 deletions(-)
create mode 100644 board/htkw/mcx/Makefile
create mode 100644 board/htkw/mcx/mcx.c
create mode 100644 board/htkw/mcx/mcx.h
create mode 100644 include/configs/mcx.h
diff --git a/MAINTAINERS b/MAINTAINERS
index a8e56bb..7e52f50 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -920,6 +920,10 @@ Richard Woodruff <r-woodruff2 at ti.com>
omap2420h4 ARM1136EJS
+Ilya Yanok <yanok at emcraft.com>
+
+ mcx ARM ARMV7 (AM35x SoC)
+
Syed Mohammed Khasim <sm.khasim at gmail.com>
Sughosh Ganu <urwithsughosh at gmail.com>
diff --git a/board/htkw/mcx/Makefile b/board/htkw/mcx/Makefile
new file mode 100644
index 0000000..4c8db10
--- /dev/null
+++ b/board/htkw/mcx/Makefile
@@ -0,0 +1,38 @@
+#
+# Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+#
+# Based on ti/evm/Makefile
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := $(BOARD).o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c
new file mode 100644
index 0000000..e593b43
--- /dev/null
+++ b/board/htkw/mcx/mcx.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on ti/evm/evm.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include <asm/gpio.h>
+#include <asm/omap_gpio.h>
+#include "errno.h"
+#include <i2c.h>
+#ifdef CONFIG_USB_EHCI
+#include <usb.h>
+#include <asm/ehci-omap.h>
+#endif
+#include "mcx.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_USB_EHCI
+static struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+int ehci_hcd_init(void)
+{
+ return omap_ehci_hcd_init(&usbhs_bdata);
+}
+
+int ehci_hcd_stop(void)
+{
+ return omap_ehci_hcd_stop();
+}
+#endif
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: late init.
+ */
+int misc_init_r(void)
+{
+ dieid_num_r();
+
+ return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * hardware. Many pins need to be moved from protect to primary
+ * mode.
+ */
+void set_muxconf_regs(void)
+{
+ MUX_MCX();
+}
+
+#if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD)
+int board_mmc_init(bd_t *bis)
+{
+ return omap_mmc_init(0);
+}
+#endif
+
+#ifdef CONFIG_USB_EHCI_OMAP
+#define USB_HOST_PWR_EN 132
+int board_usb_init(void)
+{
+ if (gpio_request(USB_HOST_PWR_EN, "USB_HOST_PWR_EN") < 0) {
+ puts("Failed to get USB_HOST_PWR_EN pin\n");
+ return -ENODEV;
+ }
+ gpio_direction_output(USB_HOST_PWR_EN, 1);
+
+ return 0;
+}
+#endif
diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
new file mode 100644
index 0000000..d675a48
--- /dev/null
+++ b/board/htkw/mcx/mcx.h
@@ -0,0 +1,408 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on ti/evm/evm.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#ifndef _AM3517EVM_H_
+#define _AM3517EVM_H_
+
+const omap3_sysinfo sysinfo = {
+ DDR_DISCRETE,
+ "HTKW mcx Board",
+ "NAND",
+};
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_MCX() \
+ /* SDRC */\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SDRC_DQS0N), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(SDRC_DQS1N), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(SDRC_DQS2N), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(SDRC_DQS3N), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(SDRC_CKE0), (M0)) \
+ MUX_VAL(CP(SDRC_CKE1), (M0)) \
+ MUX_VAL(CP(STRBEN_DLY0), (IEN | PTD | EN | M0)) \
+ /*sdrc_strben_dly0*/\
+ MUX_VAL(CP(STRBEN_DLY1), (IEN | PTD | EN | M0)) \
+ /*sdrc_strben_dly1*/\
+ /* GPMC */\
+ MUX_VAL(CP(GPMC_A1), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A2), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A3), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A4), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A5), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A6), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A7), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A8), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A9), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTU | DIS | M4)) \
+ /* GPIO_43 LCD buffer enable */ \
+ MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_NCS1), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_NCS2), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_NCS3), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M4))\
+ MUX_VAL(CP(GPMC_NCS5), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_NCS6), (IEN | PTU | EN | M4)) \
+ /* GPIO_57 TS_PenIRQn */\
+ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M4)) \
+ /* GPIO_58 ETHERNET RESET */\
+ MUX_VAL(CP(GPMC_CLK), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | DIS | M4)) \
+ /* GPIO_61 SD-CARD CD */ \
+ MUX_VAL(CP(GPMC_NWP), (IDIS | PTU | EN | M4)) \
+ /* GPIO_62 Nand write protect, keep enabled */ \
+ MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M4))\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4))\
+ MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M4)) \
+ /* GPIO_65 SD-CARD WP */\
+ /* DSS */\
+ MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA0), (IEN | PTU | EN | M4))\
+ MUX_VAL(CP(DSS_DATA1), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(DSS_DATA2), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA8), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(DSS_DATA9), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA16), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(DSS_DATA17), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(DSS_DATA18), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) \
+ /* CAMERA */\
+ MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(CAM_XCLKA), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(CAM_FLD), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D0), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D1), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D2), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D3), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D4), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D5), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D6), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D7), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D8), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D9), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D10), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_D11), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_XCLKB), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_WEN), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CAM_STROBE), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CSI2_DX0), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CSI2_DY0), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CSI2_DY1), (IEN | PTD | EN | M4)) \
+ /* MMC */\
+ MUX_VAL(CP(MMC1_CLK), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(MMC1_CMD), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M4)) \
+ \
+ MUX_VAL(CP(MMC2_CLK), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(MMC2_CMD), (IDIS | PTD | DIS | M4)) \
+ /* GPIO_131 LCD Enable */ \
+ MUX_VAL(CP(MMC2_DAT0), (IDIS | PTD | DIS | M4)) \
+ /* GPIO_132 USB host Enable */\
+ MUX_VAL(CP(MMC2_DAT1), (IDIS | PTD | DIS | M4)) \
+ /* GPIO_133 HDMI PD */\
+ MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4))\
+ /* McBSP */\
+ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M0)) \
+ MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) \
+ \
+ MUX_VAL(CP(MCBSP2_FSX), (IEN | PTU | EN | M4))\
+ MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCBSP2_DR), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCBSP2_DX), (IEN | PTU | EN | M4))\
+ \
+ MUX_VAL(CP(MCBSP3_DX), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCBSP3_DR), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCBSP3_FSX), (IEN | PTU | EN | M4))\
+ \
+ MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)) \
+ /* GPIO_152 USB phy2 reset */\
+ MUX_VAL(CP(MCBSP4_DR), (IEN | PTU | EN | M4)) \
+ /* GPIO_153 */\
+ MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M4)) \
+ /* GPIO_154 USB phy1 reset */\
+ MUX_VAL(CP(MCBSP4_FSX), (IEN | PTU | EN | M4)) \
+ /* GPIO_155 TS_BUSY */\
+ /* UART */\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) \
+ \
+ MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) \
+ \
+ MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTU | DIS | M0)) \
+ MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) \
+ MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) \
+ /* I2C */\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) \
+ /* McSPI */\
+ MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(MCSPI1_CS1), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M3)) \
+ /* HSUSB2_dat7 */\
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M3)) \
+ /* HSUSB2_dat4 */\
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M3)) \
+ /* HSUSB2_dat5 */\
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | DIS | M3)) \
+ /* HSUSB2_dat6 */\
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | DIS | M3)) \
+ /* HSUSB2_dat3 */\
+ /* CCDC */\
+ MUX_VAL(CP(CCDC_PCLK), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_FIELD), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_HD), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_VD), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_WEN), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA0), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA1), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA2), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA3), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA4), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA5), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA6), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(CCDC_DATA7), (IEN | PTD | EN | M4)) \
+ /* RMII */\
+ MUX_VAL(CP(RMII_MDIO_DATA), (IEN | M0)) \
+ MUX_VAL(CP(RMII_MDIO_CLK), (M0)) \
+ MUX_VAL(CP(RMII_RXD0), (IEN | PTD | M0)) \
+ MUX_VAL(CP(RMII_RXD1), (IEN | PTD | M0)) \
+ MUX_VAL(CP(RMII_CRS_DV), (IEN | PTD | M0)) \
+ MUX_VAL(CP(RMII_RXER), (PTD | M0)) \
+ MUX_VAL(CP(RMII_TXD0), (PTD | M0)) \
+ MUX_VAL(CP(RMII_TXD1), (PTD | M0)) \
+ MUX_VAL(CP(RMII_TXEN), (PTD | M0)) \
+ MUX_VAL(CP(RMII_50MHZ_CLK), (IEN | PTD | EN | M0)) \
+ /* HECC */\
+ MUX_VAL(CP(HECC1_TXD), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(HECC1_RXD), (IEN | PTD | EN | M4)) \
+ /* HSUSB */\
+ MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) \
+ MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(USB0_DRVBUS), (IEN | PTD | EN | M0)) \
+ /* HDQ */\
+ MUX_VAL(CP(HDQ_SIO), (IEN | PTD | EN | M4)) \
+ /* Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SYS_NIRQ), (IEN | PTD | EN | M4)) \
+ MUX_VAL(CP(SYS_NRESWARM), (IEN | PTU | DIS | M4)) \
+ /* SYS_nRESWARM */\
+ MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4))\
+ MUX_VAL(CP(SYS_BOOT6), (IEN | PTD | DIS | M4))\
+ MUX_VAL(CP(SYS_BOOT7), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(SYS_BOOT8), (IEN | PTD | DIS | M4)) \
+ \
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M4))\
+ MUX_VAL(CP(SYS_CLKOUT2), (IDIS | PTU | DIS | M4))\
+ /* JTAG */\
+ MUX_VAL(CP(JTAG_nTRST), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(JTAG_TCK), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(JTAG_TMS), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(JTAG_TDI), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(JTAG_EMU0), (IEN | PTU | EN | M4)) \
+ MUX_VAL(CP(JTAG_EMU1), (IEN | PTU | EN | M4))\
+ /* ETK (ES2 onwards) */\
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTD | DIS | M3)) \
+ /* hsusb1_stp */ \
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M3)) \
+ /* hsusb1_clk */\
+ MUX_VAL(CP(ETK_D0_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D2_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | EN | M3)) \
+ MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M4)) \
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M4)) \
+ /* Die to Die */\
+ MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) \
+ MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) \
+ MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) \
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) \
+
+#endif
diff --git a/boards.cfg b/boards.cfg
index 1f264b1..70809ca 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -214,6 +214,7 @@ omap3_evm_quick_mmc arm armv7 evm ti
omap3_evm_quick_nand arm armv7 evm ti omap3
omap3_sdp3430 arm armv7 sdp3430 ti omap3
devkit8000 arm armv7 devkit8000 timll omap3
+mcx arm armv7 mcx htkw omap3
tricorder arm armv7 tricorder corscience omap3
twister arm armv7 twister technexion omap3
omap4_panda arm armv7 panda ti omap4
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
new file mode 100644
index 0000000..0940e86
--- /dev/null
+++ b/include/configs/mcx.h
@@ -0,0 +1,378 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on omap3_evm_config.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_OMAP /* in a TI OMAP core */
+#define CONFIG_OMAP34XX /* which is a 34XX */
+#define CONFIG_OMAP3_MCX /* working with mcx */
+
+#define MACH_TYPE_MCX 3656
+#define CONFIG_MACH_TYPE MACH_TYPE_MCX
+
+#define CONFIG_SYS_CACHELINE_SIZE 64
+
+#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_FIT
+
+/*
+ * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
+ * and older u-boot.bin with the new U-Boot SPL.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80008000
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
+#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
+/*
+ * DDR related
+ */
+#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+#define CONFIG_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+
+/* EHCI */
+#define CONFIG_USB_STORAGE
+#define CONFIG_OMAP3_GPIO_5
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_ULPI
+#define CONFIG_USB_ULPI_VIEWPORT_OMAP
+/*#define CONFIG_EHCI_DCACHE*/ /* leave it disabled for now */
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 154
+#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 152
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_MTDPARTS
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_DRIVER_OMAP34XX_I2C
+
+/* RTC */
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
+ /* to access nand */
+#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
+ /* to access */
+ /* nand at CS0 */
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
+ /* NAND devices */
+#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET 0x680000
+#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* sz of jffs2 part */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 10
+
+#define CONFIG_BOOTFILE "uImage"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyO2,115200n8\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "root=/dev/mtdblock4 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 280000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmc init; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT "mcx # "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command */
+ /* args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
+ /* address */
+
+/*
+ * AM3517 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
+
+/*
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/*
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M
+
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT
+#define CONFIG_ENV_IS_IN_NAND
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+
+/*
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
+ CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_NAND_SOFTECC
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
+#define CONFIG_SPL_MAX_SIZE (45 << 10)
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+
+/* move malloc and bss high to prevent clashing with the main image */
+#define CONFIG_SYS_SPL_MALLOC_START 0x8f000000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
+#define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\
+ 48, 49, 50, 51, 52, 53, 54, 55,\
+ 56, 57, 58, 59, 60, 61, 62, 63}
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
+ CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
+ CONFIG_SYS_NAND_ECCSTEPS)
+
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+/*
+ * ethernet support
+ *
+ */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_DRIVER_TI_EMAC_USE_RMII
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#endif
+
+#endif /* __CONFIG_H */
--
1.7.5.4
More information about the U-Boot
mailing list