[U-Boot] [PATCH V8] mcx: support for HTKW mcx board
Igor Grinberg
grinberg at compulab.co.il
Wed Feb 8 11:07:24 CET 2012
On 02/08/12 11:30, Stefano Babic wrote:
> From: Ilya Yanok <yanok at emcraft.com>
>
> This patch adds support for the HTKW mcx AM3517-based board.
> Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both
> NAND and MMC SPLs are supported.
>
> Signed-off-by: Ilya Yanok <yanok at emcraft.com>
> Signed-off-by: Stefano Babic <sbabic at denx.de>
> CC: Tom Rini <tom.rini at gmail.com>
> Cc: Detlev Zundel <dzu at denx.de>
Acked-by: Igor Grinberg <grinberg at compulab.co.il>
> ---
> Changes since V7:
> - do not use temporary variable to return values (Igor Grinberg)
> - port 2 is TTL, cannot be PHY (Igor Grinberg)
>
> Changes from V6:
> - rebased on current u-boot-ti
> - applied and tested on top of EHCI Gavindraj's patches
> - uses ULPI framework
>
> Changes from V5
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/120254
>
> - added comments on CONFIG_SYS_TEXT_BASE and SPL_{MALLOC,BSS}
>
> Changes from V4
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/120148
>
> - board_mmc_init return value fixed
> - machine id added locally
> - CONFIG_SYS_NAND_U_BOOT_SIZE removed
>
> Changes from V3
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/118530
>
> - Comment for misc_init_r function fixed
> - Added check for gpio_request return value.
> - Removed #if defined(CONFIG_GENERIC_MMC) around board_mmc_init
> - CONFIG_USE_IRQ and related stuff removed from config
> - CONFIG_OMAP3_MICRON_DDR removed
> - CONFIG_SYS_MAXRAGS changed 32 -> 16
> - Incorrect multiline comments (/*--- ones) fixed
> - CONFIG_SPL_MAX_SIZE rewritten 0xB400 -> (45 << 10)
> - CONFIG_SPL_NAND_WORKSPACE removed
>
> Changes from V2
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/116548
>
> - None
>
> Changes from V1
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/115026
>
> - Calls to gpio_set_value after gpio_direction_output removed
> - Minor style problem (tab instead of space) fixed
>
> SPL series:
> Changes from V1
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112892
>
> - OMAP EHCI support enabled in config
> - MMC SPL support enabled in config
>
> "DaVinci EMAC and HTKW mcx support" series:
> Changes from V3
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112884
>
> - NAND SPL support enabled in config
>
> Changes from V2
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112317
>
> - removed dead code from board/htkw/mcx/Makefile as Mike suggested
> - removed EMAC reset (now done in generic cpu_eth_init())
> - removed some unsuned defines from configuration header
>
> Changes from V1
> http://article.gmane.org/gmane.comp.boot-loaders.u-boot/111197
>
> - various style fixes to make checkpatch (almost) happy
> - FSF address removed from GPL comments
> - CONFIG_SYS_TEXT_BASE moved to configuration header, config.mk droped
> - CONFIG_MACH_TYPE is used instead of setting mach type from board code
> - i2c_init removed from misc_init_r
> - cpu_eth_init removed (added to generic place by another patch)
> - CONTROL_PADCONF defines removed
> - Fixed boolean config options not to have a value
> - CONFIG_MUSB_* and related defines removed
>
>
> MAINTAINERS | 4 +
> board/htkw/mcx/Makefile | 38 +++++
> board/htkw/mcx/mcx.c | 112 +++++++++++++
> board/htkw/mcx/mcx.h | 408 +++++++++++++++++++++++++++++++++++++++++++++++
> boards.cfg | 1 +
> include/configs/mcx.h | 378 +++++++++++++++++++++++++++++++++++++++++++
> 6 files changed, 941 insertions(+), 0 deletions(-)
> create mode 100644 board/htkw/mcx/Makefile
> create mode 100644 board/htkw/mcx/mcx.c
> create mode 100644 board/htkw/mcx/mcx.h
> create mode 100644 include/configs/mcx.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index a8e56bb..7e52f50 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -920,6 +920,10 @@ Richard Woodruff <r-woodruff2 at ti.com>
>
> omap2420h4 ARM1136EJS
>
> +Ilya Yanok <yanok at emcraft.com>
> +
> + mcx ARM ARMV7 (AM35x SoC)
> +
> Syed Mohammed Khasim <sm.khasim at gmail.com>
> Sughosh Ganu <urwithsughosh at gmail.com>
>
> diff --git a/board/htkw/mcx/Makefile b/board/htkw/mcx/Makefile
> new file mode 100644
> index 0000000..4c8db10
> --- /dev/null
> +++ b/board/htkw/mcx/Makefile
> @@ -0,0 +1,38 @@
> +#
> +# Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> +#
> +# Based on ti/evm/Makefile
> +#
> +# This program is free software; you can redistribute it and/or modify
> +# it under the terms of the GNU General Public License as published by
> +# the Free Software Foundation; either version 2 of the License, or
> +# (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc.
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB = $(obj)lib$(BOARD).o
> +
> +COBJS := $(BOARD).o
> +
> +SRCS := $(COBJS:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS))
> +
> +$(LIB): $(obj).depend $(OBJS)
> + $(call cmd_link_o_target, $(OBJS))
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c
> new file mode 100644
> index 0000000..e593b43
> --- /dev/null
> +++ b/board/htkw/mcx/mcx.c
> @@ -0,0 +1,112 @@
> +/*
> + * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> + *
> + * Based on ti/evm/evm.c
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc.
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/mem.h>
> +#include <asm/arch/mmc_host_def.h>
> +#include <asm/arch/mux.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/mach-types.h>
> +#include <asm/gpio.h>
> +#include <asm/omap_gpio.h>
> +#include "errno.h"
> +#include <i2c.h>
> +#ifdef CONFIG_USB_EHCI
> +#include <usb.h>
> +#include <asm/ehci-omap.h>
> +#endif
> +#include "mcx.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#ifdef CONFIG_USB_EHCI
> +static struct omap_usbhs_board_data usbhs_bdata = {
> + .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
> + .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
> + .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
> +};
> +
> +int ehci_hcd_init(void)
> +{
> + return omap_ehci_hcd_init(&usbhs_bdata);
> +}
> +
> +int ehci_hcd_stop(void)
> +{
> + return omap_ehci_hcd_stop();
> +}
> +#endif
> +
> +/*
> + * Routine: board_init
> + * Description: Early hardware init.
> + */
> +int board_init(void)
> +{
> + gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
> + /* boot param addr */
> + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
> +
> + return 0;
> +}
> +
> +/*
> + * Routine: misc_init_r
> + * Description: late init.
> + */
> +int misc_init_r(void)
> +{
> + dieid_num_r();
> +
> + return 0;
> +}
> +
> +/*
> + * Routine: set_muxconf_regs
> + * Description: Setting up the configuration Mux registers specific to the
> + * hardware. Many pins need to be moved from protect to primary
> + * mode.
> + */
> +void set_muxconf_regs(void)
> +{
> + MUX_MCX();
> +}
> +
> +#if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD)
> +int board_mmc_init(bd_t *bis)
> +{
> + return omap_mmc_init(0);
> +}
> +#endif
> +
> +#ifdef CONFIG_USB_EHCI_OMAP
> +#define USB_HOST_PWR_EN 132
> +int board_usb_init(void)
> +{
> + if (gpio_request(USB_HOST_PWR_EN, "USB_HOST_PWR_EN") < 0) {
> + puts("Failed to get USB_HOST_PWR_EN pin\n");
> + return -ENODEV;
> + }
> + gpio_direction_output(USB_HOST_PWR_EN, 1);
> +
> + return 0;
> +}
> +#endif
> diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
> new file mode 100644
> index 0000000..d675a48
> --- /dev/null
> +++ b/board/htkw/mcx/mcx.h
> @@ -0,0 +1,408 @@
> +/*
> + * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> + *
> + * Based on ti/evm/evm.h
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc.
> + */
> +
> +#ifndef _AM3517EVM_H_
> +#define _AM3517EVM_H_
> +
> +const omap3_sysinfo sysinfo = {
> + DDR_DISCRETE,
> + "HTKW mcx Board",
> + "NAND",
> +};
> +
> +/*
> + * IEN - Input Enable
> + * IDIS - Input Disable
> + * PTD - Pull type Down
> + * PTU - Pull type Up
> + * DIS - Pull type selection is inactive
> + * EN - Pull type selection is active
> + * M0 - Mode 0
> + * The commented string gives the final mux configuration for that pin
> + */
> +#define MUX_MCX() \
> + /* SDRC */\
> + MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SDRC_DQS0N), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(SDRC_DQS1N), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(SDRC_DQS2N), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(SDRC_DQS3N), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(SDRC_CKE0), (M0)) \
> + MUX_VAL(CP(SDRC_CKE1), (M0)) \
> + MUX_VAL(CP(STRBEN_DLY0), (IEN | PTD | EN | M0)) \
> + /*sdrc_strben_dly0*/\
> + MUX_VAL(CP(STRBEN_DLY1), (IEN | PTD | EN | M0)) \
> + /*sdrc_strben_dly1*/\
> + /* GPMC */\
> + MUX_VAL(CP(GPMC_A1), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A2), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A3), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A4), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A5), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A6), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A7), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A8), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A9), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_A10), (IDIS | PTU | DIS | M4)) \
> + /* GPIO_43 LCD buffer enable */ \
> + MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_NCS1), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_NCS2), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_NCS3), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M4))\
> + MUX_VAL(CP(GPMC_NCS5), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_NCS6), (IEN | PTU | EN | M4)) \
> + /* GPIO_57 TS_PenIRQn */\
> + MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M4)) \
> + /* GPIO_58 ETHERNET RESET */\
> + MUX_VAL(CP(GPMC_CLK), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | DIS | M4)) \
> + /* GPIO_61 SD-CARD CD */ \
> + MUX_VAL(CP(GPMC_NWP), (IDIS | PTU | EN | M4)) \
> + /* GPIO_62 Nand write protect, keep enabled */ \
> + MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M4))\
> + MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4))\
> + MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M4)) \
> + /* GPIO_65 SD-CARD WP */\
> + /* DSS */\
> + MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA0), (IEN | PTU | EN | M4))\
> + MUX_VAL(CP(DSS_DATA1), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(DSS_DATA2), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA8), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(DSS_DATA9), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0))\
> + MUX_VAL(CP(DSS_DATA16), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(DSS_DATA17), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(DSS_DATA18), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) \
> + /* CAMERA */\
> + MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(CAM_XCLKA), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(CAM_FLD), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D0), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D1), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D2), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D3), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D4), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D5), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D6), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D7), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D8), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D9), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D10), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_D11), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_XCLKB), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_WEN), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CAM_STROBE), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CSI2_DX0), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CSI2_DY0), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CSI2_DX1), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CSI2_DY1), (IEN | PTD | EN | M4)) \
> + /* MMC */\
> + MUX_VAL(CP(MMC1_CLK), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(MMC1_CMD), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M4)) \
> + \
> + MUX_VAL(CP(MMC2_CLK), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(MMC2_CMD), (IDIS | PTD | DIS | M4)) \
> + /* GPIO_131 LCD Enable */ \
> + MUX_VAL(CP(MMC2_DAT0), (IDIS | PTD | DIS | M4)) \
> + /* GPIO_132 USB host Enable */\
> + MUX_VAL(CP(MMC2_DAT1), (IDIS | PTD | DIS | M4)) \
> + /* GPIO_133 HDMI PD */\
> + MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4))\
> + /* McBSP */\
> + MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M0)) \
> + MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) \
> + \
> + MUX_VAL(CP(MCBSP2_FSX), (IEN | PTU | EN | M4))\
> + MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCBSP2_DR), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCBSP2_DX), (IEN | PTU | EN | M4))\
> + \
> + MUX_VAL(CP(MCBSP3_DX), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCBSP3_DR), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCBSP3_FSX), (IEN | PTU | EN | M4))\
> + \
> + MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)) \
> + /* GPIO_152 USB phy2 reset */\
> + MUX_VAL(CP(MCBSP4_DR), (IEN | PTU | EN | M4)) \
> + /* GPIO_153 */\
> + MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M4)) \
> + /* GPIO_154 USB phy1 reset */\
> + MUX_VAL(CP(MCBSP4_FSX), (IEN | PTU | EN | M4)) \
> + /* GPIO_155 TS_BUSY */\
> + /* UART */\
> + MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) \
> + \
> + MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) \
> + \
> + MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTU | DIS | M0)) \
> + MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) \
> + MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) \
> + /* I2C */\
> + MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) \
> + /* McSPI */\
> + MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(MCSPI1_CS1), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCSPI1_CS3), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M3)) \
> + /* HSUSB2_dat7 */\
> + MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M3)) \
> + /* HSUSB2_dat4 */\
> + MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M3)) \
> + /* HSUSB2_dat5 */\
> + MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | DIS | M3)) \
> + /* HSUSB2_dat6 */\
> + MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | DIS | M3)) \
> + /* HSUSB2_dat3 */\
> + /* CCDC */\
> + MUX_VAL(CP(CCDC_PCLK), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_FIELD), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_HD), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_VD), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_WEN), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA0), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA1), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA2), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA3), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA4), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA5), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA6), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(CCDC_DATA7), (IEN | PTD | EN | M4)) \
> + /* RMII */\
> + MUX_VAL(CP(RMII_MDIO_DATA), (IEN | M0)) \
> + MUX_VAL(CP(RMII_MDIO_CLK), (M0)) \
> + MUX_VAL(CP(RMII_RXD0), (IEN | PTD | M0)) \
> + MUX_VAL(CP(RMII_RXD1), (IEN | PTD | M0)) \
> + MUX_VAL(CP(RMII_CRS_DV), (IEN | PTD | M0)) \
> + MUX_VAL(CP(RMII_RXER), (PTD | M0)) \
> + MUX_VAL(CP(RMII_TXD0), (PTD | M0)) \
> + MUX_VAL(CP(RMII_TXD1), (PTD | M0)) \
> + MUX_VAL(CP(RMII_TXEN), (PTD | M0)) \
> + MUX_VAL(CP(RMII_50MHZ_CLK), (IEN | PTD | EN | M0)) \
> + /* HECC */\
> + MUX_VAL(CP(HECC1_TXD), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(HECC1_RXD), (IEN | PTD | EN | M4)) \
> + /* HSUSB */\
> + MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) \
> + MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(USB0_DRVBUS), (IEN | PTD | EN | M0)) \
> + /* HDQ */\
> + MUX_VAL(CP(HDQ_SIO), (IEN | PTD | EN | M4)) \
> + /* Control and debug */\
> + MUX_VAL(CP(SYS_32K), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SYS_NIRQ), (IEN | PTD | EN | M4)) \
> + MUX_VAL(CP(SYS_NRESWARM), (IEN | PTU | DIS | M4)) \
> + /* SYS_nRESWARM */\
> + MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4))\
> + MUX_VAL(CP(SYS_BOOT6), (IEN | PTD | DIS | M4))\
> + MUX_VAL(CP(SYS_BOOT7), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(SYS_BOOT8), (IEN | PTD | DIS | M4)) \
> + \
> + MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M4))\
> + MUX_VAL(CP(SYS_CLKOUT2), (IDIS | PTU | DIS | M4))\
> + /* JTAG */\
> + MUX_VAL(CP(JTAG_nTRST), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(JTAG_TCK), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(JTAG_TMS), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(JTAG_TDI), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(JTAG_EMU0), (IEN | PTU | EN | M4)) \
> + MUX_VAL(CP(JTAG_EMU1), (IEN | PTU | EN | M4))\
> + /* ETK (ES2 onwards) */\
> + MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTD | DIS | M3)) \
> + /* hsusb1_stp */ \
> + MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M3)) \
> + /* hsusb1_clk */\
> + MUX_VAL(CP(ETK_D0_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D2_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | EN | M3)) \
> + MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M4)) \
> + MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M4)) \
> + /* Die to Die */\
> + MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) \
> + MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) \
> + MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) \
> + MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) \
> +
> +#endif
> diff --git a/boards.cfg b/boards.cfg
> index 1f264b1..70809ca 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -214,6 +214,7 @@ omap3_evm_quick_mmc arm armv7 evm ti
> omap3_evm_quick_nand arm armv7 evm ti omap3
> omap3_sdp3430 arm armv7 sdp3430 ti omap3
> devkit8000 arm armv7 devkit8000 timll omap3
> +mcx arm armv7 mcx htkw omap3
> tricorder arm armv7 tricorder corscience omap3
> twister arm armv7 twister technexion omap3
> omap4_panda arm armv7 panda ti omap4
> diff --git a/include/configs/mcx.h b/include/configs/mcx.h
> new file mode 100644
> index 0000000..0940e86
> --- /dev/null
> +++ b/include/configs/mcx.h
> @@ -0,0 +1,378 @@
> +/*
> + * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> + *
> + * Based on omap3_evm_config.h
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc.
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +/*
> + * High Level Configuration Options
> + */
> +#define CONFIG_OMAP /* in a TI OMAP core */
> +#define CONFIG_OMAP34XX /* which is a 34XX */
> +#define CONFIG_OMAP3_MCX /* working with mcx */
> +
> +#define MACH_TYPE_MCX 3656
> +#define CONFIG_MACH_TYPE MACH_TYPE_MCX
> +
> +#define CONFIG_SYS_CACHELINE_SIZE 64
> +
> +#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
> +
> +#include <asm/arch/cpu.h> /* get chip and board defs */
> +#include <asm/arch/omap3.h>
> +
> +#define CONFIG_OF_LIBFDT
> +#define CONFIG_FIT
> +
> +/*
> + * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
> + * and older u-boot.bin with the new U-Boot SPL.
> + */
> +#define CONFIG_SYS_TEXT_BASE 0x80008000
> +
> +/*
> + * Display CPU and Board information
> + */
> +#define CONFIG_DISPLAY_CPUINFO
> +#define CONFIG_DISPLAY_BOARDINFO
> +
> +/* Clock Defines */
> +#define V_OSCK 26000000 /* Clock output from T2 */
> +#define V_SCLK (V_OSCK >> 1)
> +
> +#define CONFIG_MISC_INIT_R
> +
> +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_INITRD_TAG
> +#define CONFIG_REVISION_TAG
> +
> +/*
> + * Size of malloc() pool
> + */
> +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
> +#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
> +/*
> + * DDR related
> + */
> +#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
> +
> +/*
> + * Hardware drivers
> + */
> +
> +/*
> + * NS16550 Configuration
> + */
> +#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
> +
> +#define CONFIG_SYS_NS16550
> +#define CONFIG_SYS_NS16550_SERIAL
> +#define CONFIG_SYS_NS16550_REG_SIZE (-4)
> +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
> +
> +/*
> + * select serial console configuration
> + */
> +#define CONFIG_CONS_INDEX 3
> +#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
> +#define CONFIG_SERIAL3 3 /* UART3 */
> +
> +/* allow to overwrite serial and ethaddr */
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_BAUDRATE 115200
> +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
> + 115200}
> +#define CONFIG_MMC
> +#define CONFIG_OMAP_HSMMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_DOS_PARTITION
> +
> +/* EHCI */
> +#define CONFIG_USB_STORAGE
> +#define CONFIG_OMAP3_GPIO_5
> +#define CONFIG_USB_EHCI
> +#define CONFIG_USB_EHCI_OMAP
> +#define CONFIG_USB_ULPI
> +#define CONFIG_USB_ULPI_VIEWPORT_OMAP
> +/*#define CONFIG_EHCI_DCACHE*/ /* leave it disabled for now */
> +#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 154
> +#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 152
> +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
> +
> +/* commands to include */
> +#include <config_cmd_default.h>
> +
> +#define CONFIG_CMD_EXT2 /* EXT2 Support */
> +#define CONFIG_CMD_FAT /* FAT support */
> +#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
> +
> +#define CONFIG_CMD_DATE
> +#define CONFIG_CMD_I2C /* I2C serial bus support */
> +#define CONFIG_CMD_MMC /* MMC support */
> +#define CONFIG_CMD_FAT /* FAT support */
> +#define CONFIG_CMD_USB
> +#define CONFIG_CMD_NAND /* NAND support */
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_CACHE
> +#define CONFIG_CMD_UBI
> +#define CONFIG_CMD_UBIFS
> +#define CONFIG_RBTREE
> +#define CONFIG_LZO
> +#define CONFIG_MTD_PARTITIONS
> +#define CONFIG_MTD_DEVICE
> +#define CONFIG_CMD_MTDPARTS
> +
> +#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
> +#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
> +#undef CONFIG_CMD_IMI /* iminfo */
> +#undef CONFIG_CMD_IMLS /* List all found images */
> +
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_HARD_I2C
> +#define CONFIG_SYS_I2C_SPEED 100000
> +#define CONFIG_SYS_I2C_SLAVE 1
> +#define CONFIG_SYS_I2C_BUS 0
> +#define CONFIG_DRIVER_OMAP34XX_I2C
> +
> +/* RTC */
> +#define CONFIG_RTC_DS1337
> +#define CONFIG_SYS_I2C_RTC_ADDR 0x68
> +
> +#define CONFIG_CMD_NET
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_NFS
> +/*
> + * Board NAND Info.
> + */
> +#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
> + /* to access nand */
> +#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
> + /* to access */
> + /* nand at CS0 */
> +
> +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
> + /* NAND devices */
> +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
> +
> +#define CONFIG_JFFS2_NAND
> +/* nand device jffs2 lives on */
> +#define CONFIG_JFFS2_DEV "nand0"
> +/* start of jffs2 partition */
> +#define CONFIG_JFFS2_PART_OFFSET 0x680000
> +#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* sz of jffs2 part */
> +
> +/* Environment information */
> +#define CONFIG_BOOTDELAY 10
> +
> +#define CONFIG_BOOTFILE "uImage"
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "loadaddr=0x82000000\0" \
> + "console=ttyO2,115200n8\0" \
> + "mmcargs=setenv bootargs console=${console} " \
> + "root=/dev/mmcblk0p2 rw " \
> + "rootfstype=ext3 rootwait\0" \
> + "nandargs=setenv bootargs console=${console} " \
> + "root=/dev/mtdblock4 rw " \
> + "rootfstype=jffs2\0" \
> + "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
> + "bootscript=echo Running bootscript from mmc ...; " \
> + "source ${loadaddr}\0" \
> + "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
> + "mmcboot=echo Booting from mmc ...; " \
> + "run mmcargs; " \
> + "bootm ${loadaddr}\0" \
> + "nandboot=echo Booting from nand ...; " \
> + "run nandargs; " \
> + "nand read ${loadaddr} 280000 400000; " \
> + "bootm ${loadaddr}\0" \
> +
> +#define CONFIG_BOOTCOMMAND \
> + "if mmc init; then " \
> + "if run loadbootscript; then " \
> + "run bootscript; " \
> + "else " \
> + "if run loaduimage; then " \
> + "run mmcboot; " \
> + "else run nandboot; " \
> + "fi; " \
> + "fi; " \
> + "else run nandboot; fi"
> +
> +#define CONFIG_AUTO_COMPLETE
> +/*
> + * Miscellaneous configurable options
> + */
> +#define V_PROMPT "mcx # "
> +
> +#define CONFIG_SYS_LONGHELP /* undef to save memory */
> +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
> +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> +#define CONFIG_SYS_PROMPT V_PROMPT
> +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
> +/* Print Buffer Size */
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
> + sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_MAXARGS 16 /* max number of command */
> + /* args */
> +/* Boot Argument Buffer Size */
> +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
> +/* memtest works on */
> +#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
> +#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
> + 0x01F00000) /* 31MB */
> +
> +#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
> + /* address */
> +
> +/*
> + * AM3517 has 12 GP timers, they can be driven by the system clock
> + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
> + * This rate is divided by a local divisor.
> + */
> +#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
> +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
> +#define CONFIG_SYS_HZ 1000
> +
> +/*
> + * Stack sizes
> + *
> + * The stack sizes are set up in start.S using the settings below
> + */
> +#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
> +
> +/*
> + * Physical Memory Map
> + */
> +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
> +#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
> +#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
> +#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
> +
> +/*
> + * FLASH and environment organization
> + */
> +
> +/* **** PISMO SUPPORT *** */
> +
> +/* Configure the PISMO */
> +#define PISMO1_NAND_SIZE GPMC_SIZE_128M
> +
> +#define CONFIG_NAND_OMAP_GPMC
> +#define GPMC_NAND_ECC_LP_x16_LAYOUT
> +#define CONFIG_ENV_IS_IN_NAND
> +#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
> +
> +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
> +#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
> +#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
> +
> +/*
> + * CFI FLASH driver setup
> + */
> +/* timeout values are in ticks */
> +#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
> +#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
> +
> +/* Flash banks JFFS2 should use */
> +#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
> + CONFIG_SYS_MAX_NAND_DEVICE)
> +#define CONFIG_SYS_JFFS2_MEM_NAND
> +/* use flash_info[2] */
> +#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
> +#define CONFIG_SYS_JFFS2_NUM_BANKS 1
> +
> +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
> +#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
> +#define CONFIG_SYS_INIT_RAM_SIZE 0x800
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
> + CONFIG_SYS_INIT_RAM_SIZE - \
> + GENERATED_GBL_DATA_SIZE)
> +
> +/* Defines for SPL */
> +#define CONFIG_SPL
> +#define CONFIG_SPL_NAND_SIMPLE
> +#define CONFIG_SPL_NAND_SOFTECC
> +
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBDISK_SUPPORT
> +#define CONFIG_SPL_I2C_SUPPORT
> +#define CONFIG_SPL_MMC_SUPPORT
> +#define CONFIG_SPL_FAT_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +#define CONFIG_SPL_SERIAL_SUPPORT
> +#define CONFIG_SPL_POWER_SUPPORT
> +#define CONFIG_SPL_NAND_SUPPORT
> +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
> +
> +#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
> +#define CONFIG_SPL_MAX_SIZE (45 << 10)
> +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
> +
> +/* move malloc and bss high to prevent clashing with the main image */
> +#define CONFIG_SYS_SPL_MALLOC_START 0x8f000000
> +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
> +#define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */
> +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
> +
> +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
> +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
> +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
> +
> +/* NAND boot config */
> +#define CONFIG_SYS_NAND_PAGE_COUNT 64
> +#define CONFIG_SYS_NAND_PAGE_SIZE 2048
> +#define CONFIG_SYS_NAND_OOBSIZE 64
> +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
> +#define CONFIG_SYS_NAND_5_ADDR_CYCLE
> +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
> +#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\
> + 48, 49, 50, 51, 52, 53, 54, 55,\
> + 56, 57, 58, 59, 60, 61, 62, 63}
> +#define CONFIG_SYS_NAND_ECCSIZE 256
> +#define CONFIG_SYS_NAND_ECCBYTES 3
> +
> +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
> + CONFIG_SYS_NAND_ECCSIZE)
> +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
> + CONFIG_SYS_NAND_ECCSTEPS)
> +
> +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
> +
> +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
> +
> +/*
> + * ethernet support
> + *
> + */
> +#if defined(CONFIG_CMD_NET)
> +#define CONFIG_DRIVER_TI_EMAC
> +#define CONFIG_DRIVER_TI_EMAC_USE_RMII
> +#define CONFIG_MII
> +#define CONFIG_BOOTP_DEFAULT
> +#define CONFIG_BOOTP_DNS
> +#define CONFIG_BOOTP_DNS2
> +#define CONFIG_BOOTP_SEND_HOSTNAME
> +#define CONFIG_NET_RETRY_COUNT 10
> +#endif
> +
> +#endif /* __CONFIG_H */
--
Regards,
Igor.
More information about the U-Boot
mailing list