[U-Boot] [PATCH v2 4/6] omap_gpmc: change nandecc command
Andreas Bießmann
andreas.devel at googlemail.com
Tue Apr 2 18:05:56 CEST 2013
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine. Currently we support 1-bit hammign
and 8-bit BCH on HW backend.
In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.
Signed-off-by: Andreas Bießmann <andreas.devel at googlemail.com>
Cc: Tom Rini <trini at ti.com>
---
new in v2
arch/arm/cpu/armv7/omap3/board.c | 31 ++++++++++----
arch/arm/include/asm/arch-am33xx/sys_proto.h | 2 +-
arch/arm/include/asm/arch-omap3/sys_proto.h | 2 +-
drivers/mtd/nand/omap_gpmc.c | 56 ++++++++++++++------------
4 files changed, 55 insertions(+), 36 deletions(-)
diff --git a/arch/arm/cpu/armv7/omap3/board.c b/arch/arm/cpu/armv7/omap3/board.c
index c6d9a42..b72fadc 100644
--- a/arch/arm/cpu/armv7/omap3/board.c
+++ b/arch/arm/cpu/armv7/omap3/board.c
@@ -328,14 +328,25 @@ void abort(void)
*****************************************************************************/
static int do_switch_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
{
- if (argc != 2)
+ if (argc < 2 || argc > 3)
goto usage;
- if (strncmp(argv[1], "hw", 2) == 0)
- omap_nand_switch_ecc(1);
- else if (strncmp(argv[1], "sw", 2) == 0)
- omap_nand_switch_ecc(0);
- else
+
+ if (strncmp(argv[1], "hw", 2) == 0) {
+ if (argc == 2) {
+ omap_nand_switch_ecc(1, 1);
+ } else {
+ if (strncmp(argv[2], "hamming", 7) == 0)
+ omap_nand_switch_ecc(1, 1);
+ else if (strncmp(argv[2], "bch8", 4) == 0)
+ omap_nand_switch_ecc(1, 8);
+ else
+ goto usage;
+ }
+ } else if (strncmp(argv[1], "sw", 2) == 0) {
+ omap_nand_switch_ecc(0, 0);
+ } else {
goto usage;
+ }
return 0;
@@ -345,9 +356,13 @@ usage:
}
U_BOOT_CMD(
- nandecc, 2, 1, do_switch_ecc,
+ nandecc, 3, 1, do_switch_ecc,
"switch OMAP3 NAND ECC calculation algorithm",
- "[hw/sw] - Switch between NAND hardware (hw) or software (sw) ecc algorithm"
+ "hw [hamming|bch8] - Switch between NAND hardware 1-bit hamming and"
+ " 8-bit BCH\n"
+ " ecc calculation (second parameter may"
+ " be omitted).\n"
+ "nandecc sw - Switch to NAND software ecc algorithm."
);
#endif /* CONFIG_NAND_OMAP_GPMC & !CONFIG_SPL_BUILD */
diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h b/arch/arm/include/asm/arch-am33xx/sys_proto.h
index 0910a94..c913b5f 100644
--- a/arch/arm/include/asm/arch-am33xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h
@@ -39,5 +39,5 @@ struct gpmc_cs;
void gpmc_init(void);
void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
u32 size);
-void omap_nand_switch_ecc(int);
+void omap_nand_switch_ecc(uint32_t, uint32_t);
#endif
diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
index d60f2ad..dae1312 100644
--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
@@ -78,7 +78,7 @@ void sr32(void *, u32, u32, u32);
u32 wait_on_value(u32, u32, void *, u32);
void sdelay(unsigned long);
void make_cs1_contiguous(void);
-void omap_nand_switch_ecc(int);
+void omap_nand_switch_ecc(uint32_t, uint32_t);
void power_init_r(void);
void dieid_num_r(void);
void do_omap3_emu_romcode_call(u32 service_id, u32 parameters);
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index c7d4999..f073cbe 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -604,13 +604,14 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
#ifndef CONFIG_SPL_BUILD
/*
- * omap_nand_switch_ecc - switch the ECC operation b/w h/w ecc and s/w ecc.
- * The default is to come up on s/w ecc
- *
- * @hardware - 1 -switch to h/w ecc, 0 - s/w ecc
+ * omap_nand_switch_ecc - switch the ECC operation between different engines
+ * (h/w and s/w) and different algorithms (hamming and BCHx)
*
+ * @hardware - true if one of the HW engines should be used
+ * @eccstrength - the number of bits that could be corrected
+ * (1 - hamming, 4 - BCH4, 8 - BCH8, 16 - BCH16)
*/
-void omap_nand_switch_ecc(int32_t hardware)
+void omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength)
{
struct nand_chip *nand;
struct mtd_info *mtd;
@@ -637,28 +638,31 @@ void omap_nand_switch_ecc(int32_t hardware)
nand->ecc.calculate = NULL;
/* Setup the ecc configurations again */
- if (hardware == 1) {
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_nand_oob;
- nand->ecc.size = 512;
- nand->ecc.bytes = 3;
- nand->ecc.hwctl = omap_enable_hwecc;
- nand->ecc.correct = omap_correct_data;
- nand->ecc.calculate = omap_calculate_ecc;
- omap_hwecc_init(nand);
- printf("HW ECC selected\n");
+ if (hardware) {
+ if (eccstrength == 1) {
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_nand_oob;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 3;
+ nand->ecc.hwctl = omap_enable_hwecc;
+ nand->ecc.correct = omap_correct_data;
+ nand->ecc.calculate = omap_calculate_ecc;
+ omap_hwecc_init(nand);
+ printf("1-bit hamming HW ECC selected\n");
+ }
#ifdef CONFIG_AM33XX
- } else if (hardware == 2) {
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_bch8_nand_oob;
- nand->ecc.size = 512;
- nand->ecc.bytes = 14;
- nand->ecc.read_page = omap_read_page_bch;
- nand->ecc.hwctl = omap_enable_ecc_bch;
- nand->ecc.correct = omap_correct_data_bch;
- nand->ecc.calculate = omap_calculate_ecc_bch;
- omap_hwecc_init_bch(nand, NAND_ECC_READ);
- printf("HW BCH8 selected\n");
+ else if (eccstrength == 8) {
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_bch8_nand_oob;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 14;
+ nand->ecc.read_page = omap_read_page_bch;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc_bch;
+ omap_hwecc_init_bch(nand, NAND_ECC_READ);
+ printf("8-bit BCH HW ECC selected\n");
+ }
#endif
} else {
nand->ecc.mode = NAND_ECC_SOFT;
--
1.7.10.4
More information about the U-Boot
mailing list