[U-Boot] [PATCH v10 27/30] arm: Remove support for unused s3c64xx

Benoît Thébaudeau benoit.thebaudeau at advansee.com
Wed Apr 3 08:04:49 CEST 2013


Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau at advansee.com>
---
Changes in v10: None
Changes in v9:
 - Do not use "scrapyard" in patch description because this is reserved to refer
   to the board scrapyard file.

Changes in v8:
 - New patch.

Changes in v7: None
Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None

 arch/arm/cpu/arm1176/s3c64xx/Makefile        |   50 --
 arch/arm/cpu/arm1176/s3c64xx/config.mk       |   34 -
 arch/arm/cpu/arm1176/s3c64xx/cpu_init.S      |  135 ----
 arch/arm/cpu/arm1176/s3c64xx/init.c          |   26 -
 arch/arm/cpu/arm1176/s3c64xx/reset.S         |   34 -
 arch/arm/cpu/arm1176/s3c64xx/speed.c         |  145 -----
 arch/arm/cpu/arm1176/s3c64xx/timer.c         |  160 -----
 arch/arm/include/asm/arch-s3c64xx/hardware.h |   63 --
 arch/arm/include/asm/arch-s3c64xx/s3c6400.h  |  895 --------------------------
 arch/arm/include/asm/arch-s3c64xx/s3c64x0.h  |   90 ---
 doc/driver-model/UDM-serial.txt              |   42 +-
 drivers/mtd/nand/Makefile                    |    1 -
 drivers/mtd/nand/s3c64xx.c                   |  295 ---------
 drivers/mtd/onenand/onenand_base.c           |    4 -
 drivers/mtd/onenand/samsung.c                |   60 +-
 drivers/serial/Makefile                      |    1 -
 drivers/serial/s3c64xx.c                     |  187 ------
 drivers/serial/serial.c                      |    2 -
 drivers/usb/host/Makefile                    |    1 -
 drivers/usb/host/ohci-hcd.c                  |    1 -
 drivers/usb/host/s3c64xx-hcd.c               |   45 --
 include/common.h                             |    1 -
 include/onenand_uboot.h                      |    4 -
 23 files changed, 23 insertions(+), 2253 deletions(-)
 delete mode 100644 arch/arm/cpu/arm1176/s3c64xx/Makefile
 delete mode 100644 arch/arm/cpu/arm1176/s3c64xx/config.mk
 delete mode 100644 arch/arm/cpu/arm1176/s3c64xx/cpu_init.S
 delete mode 100644 arch/arm/cpu/arm1176/s3c64xx/init.c
 delete mode 100644 arch/arm/cpu/arm1176/s3c64xx/reset.S
 delete mode 100644 arch/arm/cpu/arm1176/s3c64xx/speed.c
 delete mode 100644 arch/arm/cpu/arm1176/s3c64xx/timer.c
 delete mode 100644 arch/arm/include/asm/arch-s3c64xx/hardware.h
 delete mode 100644 arch/arm/include/asm/arch-s3c64xx/s3c6400.h
 delete mode 100644 arch/arm/include/asm/arch-s3c64xx/s3c64x0.h
 delete mode 100644 drivers/mtd/nand/s3c64xx.c
 delete mode 100644 drivers/serial/s3c64xx.c
 delete mode 100644 drivers/usb/host/s3c64xx-hcd.c

diff --git a/arch/arm/cpu/arm1176/s3c64xx/Makefile b/arch/arm/cpu/arm1176/s3c64xx/Makefile
deleted file mode 100644
index 266a073..0000000
--- a/arch/arm/cpu/arm1176/s3c64xx/Makefile
+++ /dev/null
@@ -1,50 +0,0 @@
-#
-# (C) Copyright 2000-2003
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2008
-# Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(SOC).o
-
-SOBJS	= reset.o
-
-COBJS-$(CONFIG_S3C6400)	+= cpu_init.o speed.o
-COBJS-y	+= timer.o init.o
-
-OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))
-
-all:	$(obj).depend $(START) $(LIB)
-
-$(LIB):	$(OBJS)
-	$(call cmd_link_o_target, $(OBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/arch/arm/cpu/arm1176/s3c64xx/config.mk b/arch/arm/cpu/arm1176/s3c64xx/config.mk
deleted file mode 100644
index 222d352..0000000
--- a/arch/arm/cpu/arm1176/s3c64xx/config.mk
+++ /dev/null
@@ -1,34 +0,0 @@
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj at denx.de>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-PLATFORM_RELFLAGS += -fno-common -ffixed-r8 -msoft-float
-
-# Make ARMv5 to allow more compilers to work, even though its v6.
-PLATFORM_CPPFLAGS += -march=armv5t
-# =========================================================================
-#
-# Supply options according to compiler version
-#
-# =========================================================================
-PF_RELFLAGS_SLB_AT := $(call cc-option,-mshort-load-bytes,\
-			$(call cc-option,-malignment-traps,))
-PLATFORM_RELFLAGS += $(PF_RELFLAGS_SLB_AT)
diff --git a/arch/arm/cpu/arm1176/s3c64xx/cpu_init.S b/arch/arm/cpu/arm1176/s3c64xx/cpu_init.S
deleted file mode 100644
index df88cba..0000000
--- a/arch/arm/cpu/arm1176/s3c64xx/cpu_init.S
+++ /dev/null
@@ -1,135 +0,0 @@
-/*
- * Originates from Samsung's u-boot 1.1.6 port to S3C6400 / SMDK6400
- *
- * Copyright (C) 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <asm/arch/s3c6400.h>
-
-	.globl mem_ctrl_asm_init
-mem_ctrl_asm_init:
-	/* DMC1 base address 0x7e001000 */
-	ldr	r0, =ELFIN_DMC1_BASE
-
-	ldr	r1, =0x4
-	str	r1, [r0, #INDEX_DMC_MEMC_CMD]
-
-	ldr	r1, =DMC_DDR_REFRESH_PRD
-	str	r1, [r0, #INDEX_DMC_REFRESH_PRD]
-
-	ldr	r1, =DMC_DDR_CAS_LATENCY
-	str	r1, [r0, #INDEX_DMC_CAS_LATENCY]
-
-	ldr	r1, =DMC_DDR_t_DQSS
-	str	r1, [r0, #INDEX_DMC_T_DQSS]
-
-	ldr	r1, =DMC_DDR_t_MRD
-	str	r1, [r0, #INDEX_DMC_T_MRD]
-
-	ldr	r1, =DMC_DDR_t_RAS
-	str	r1, [r0, #INDEX_DMC_T_RAS]
-
-	ldr	r1, =DMC_DDR_t_RC
-	str	r1, [r0, #INDEX_DMC_T_RC]
-
-	ldr	r1, =DMC_DDR_t_RCD
-	ldr	r2, =DMC_DDR_schedule_RCD
-	orr	r1, r1, r2
-	str	r1, [r0, #INDEX_DMC_T_RCD]
-
-	ldr	r1, =DMC_DDR_t_RFC
-	ldr	r2, =DMC_DDR_schedule_RFC
-	orr	r1, r1, r2
-	str	r1, [r0, #INDEX_DMC_T_RFC]
-
-	ldr	r1, =DMC_DDR_t_RP
-	ldr	r2, =DMC_DDR_schedule_RP
-	orr	r1, r1, r2
-	str	r1, [r0, #INDEX_DMC_T_RP]
-
-	ldr	r1, =DMC_DDR_t_RRD
-	str	r1, [r0, #INDEX_DMC_T_RRD]
-
-	ldr	r1, =DMC_DDR_t_WR
-	str	r1, [r0, #INDEX_DMC_T_WR]
-
-	ldr	r1, =DMC_DDR_t_WTR
-	str	r1, [r0, #INDEX_DMC_T_WTR]
-
-	ldr	r1, =DMC_DDR_t_XP
-	str	r1, [r0, #INDEX_DMC_T_XP]
-
-	ldr	r1, =DMC_DDR_t_XSR
-	str	r1, [r0, #INDEX_DMC_T_XSR]
-
-	ldr	r1, =DMC_DDR_t_ESR
-	str	r1, [r0, #INDEX_DMC_T_ESR]
-
-	ldr	r1, =DMC1_MEM_CFG
-	str	r1, [r0, #INDEX_DMC_MEMORY_CFG]
-
-	ldr	r1, =DMC1_MEM_CFG2
-	str	r1, [r0, #INDEX_DMC_MEMORY_CFG2]
-
-	ldr	r1, =DMC1_CHIP0_CFG
-	str	r1, [r0, #INDEX_DMC_CHIP_0_CFG]
-
-	ldr	r1, =DMC_DDR_32_CFG
-	str	r1, [r0, #INDEX_DMC_USER_CONFIG]
-
-	/* DMC0 DDR Chip 0 configuration direct command reg */
-	ldr	r1, =DMC_NOP0
-	str	r1, [r0, #INDEX_DMC_DIRECT_CMD]
-
-	/* Precharge All */
-	ldr	r1, =DMC_PA0
-	str	r1, [r0, #INDEX_DMC_DIRECT_CMD]
-
-	/* Auto Refresh 2 time */
-	ldr	r1, =DMC_AR0
-	str	r1, [r0, #INDEX_DMC_DIRECT_CMD]
-	str	r1, [r0, #INDEX_DMC_DIRECT_CMD]
-
-	/* MRS */
-	ldr	r1, =DMC_mDDR_EMR0
-	str	r1, [r0, #INDEX_DMC_DIRECT_CMD]
-
-	/* Mode Reg */
-	ldr	r1, =DMC_mDDR_MR0
-	str	r1, [r0, #INDEX_DMC_DIRECT_CMD]
-
-	/* Enable DMC1 */
-	mov	r1, #0x0
-	str	r1, [r0, #INDEX_DMC_MEMC_CMD]
-
-check_dmc1_ready:
-	ldr	r1, [r0, #INDEX_DMC_MEMC_STATUS]
-	mov	r2, #0x3
-	and	r1, r1, r2
-	cmp	r1, #0x1
-	bne	check_dmc1_ready
-	nop
-
-	mov	pc, lr
-
-	.ltorg
diff --git a/arch/arm/cpu/arm1176/s3c64xx/init.c b/arch/arm/cpu/arm1176/s3c64xx/init.c
deleted file mode 100644
index f113d8e..0000000
--- a/arch/arm/cpu/arm1176/s3c64xx/init.c
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * (C) Copyright 2012 Ashok Kumar Reddy Kourla
- * ashokkourla2000 at gmail.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include<common.h>
-
-int arch_cpu_init(void)
-{
-	icache_enable();
-
-	return 0;
-}
diff --git a/arch/arm/cpu/arm1176/s3c64xx/reset.S b/arch/arm/cpu/arm1176/s3c64xx/reset.S
deleted file mode 100644
index eae572e..0000000
--- a/arch/arm/cpu/arm1176/s3c64xx/reset.S
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * Copyright (c) 2009 Samsung Electronics.
- * Minkyu Kang <mk7.kang at samsung.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <asm/arch/s3c6400.h>
-
-.globl reset_cpu
-reset_cpu:
-	ldr	r1, =ELFIN_CLOCK_POWER_BASE
-	ldr	r2, [r1, #SYS_ID_OFFSET]
-	ldr	r3, =0xffff
-	and	r2, r3, r2, lsr #12
-	str	r2, [r1, #SW_RST_OFFSET]
-_loop_forever:
-	b	_loop_forever
diff --git a/arch/arm/cpu/arm1176/s3c64xx/speed.c b/arch/arm/cpu/arm1176/s3c64xx/speed.c
deleted file mode 100644
index 11962ac..0000000
--- a/arch/arm/cpu/arm1176/s3c64xx/speed.c
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * (C) Copyright 2001-2004
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, d.mueller at elsoft.ch
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * This code should work for both the S3C2400 and the S3C2410
- * as they seem to have the same PLL and clock machinery inside.
- * The different address mapping is handled by the s3c24xx.h files below.
- */
-
-#include <common.h>
-#include <asm/arch/s3c6400.h>
-
-#define APLL 0
-#define MPLL 1
-#define EPLL 2
-
-/* ------------------------------------------------------------------------- */
-/*
- * NOTE: This describes the proper use of this file.
- *
- * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL.
- *
- * get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of
- * the specified bus in HZ.
- */
-/* ------------------------------------------------------------------------- */
-
-static ulong get_PLLCLK(int pllreg)
-{
-	ulong r, m, p, s;
-
-	switch (pllreg) {
-	case APLL:
-		r = APLL_CON_REG;
-		break;
-	case MPLL:
-		r = MPLL_CON_REG;
-		break;
-	case EPLL:
-		r = EPLL_CON0_REG;
-		break;
-	default:
-		hang();
-	}
-
-	m = (r >> 16) & 0x3ff;
-	p = (r >> 8) & 0x3f;
-	s = r & 0x7;
-
-	return m * (CONFIG_SYS_CLK_FREQ / (p * (1 << s)));
-}
-
-/* return ARMCORE frequency */
-ulong get_ARMCLK(void)
-{
-	ulong div;
-
-	div = CLK_DIV0_REG;
-
-	return get_PLLCLK(APLL) / ((div & 0x7) + 1);
-}
-
-/* return FCLK frequency */
-ulong get_FCLK(void)
-{
-	return get_PLLCLK(APLL);
-}
-
-/* return HCLK frequency */
-ulong get_HCLK(void)
-{
-	ulong fclk;
-
-	uint hclkx2_div = ((CLK_DIV0_REG >> 9) & 0x7) + 1;
-	uint hclk_div = ((CLK_DIV0_REG >> 8) & 0x1) + 1;
-
-	/*
-	 * Bit 7 exists on s3c6410, and not on s3c6400, it is reserved on
-	 * s3c6400 and is always 0, and it is indeed running in ASYNC mode
-	 */
-	if (OTHERS_REG & 0x80)
-		fclk = get_FCLK();		/* SYNC Mode	*/
-	else
-		fclk = get_PLLCLK(MPLL);	/* ASYNC Mode	*/
-
-	return fclk / (hclk_div * hclkx2_div);
-}
-
-/* return PCLK frequency */
-ulong get_PCLK(void)
-{
-	ulong fclk;
-	uint hclkx2_div = ((CLK_DIV0_REG >> 9) & 0x7) + 1;
-	uint pre_div = ((CLK_DIV0_REG >> 12) & 0xf) + 1;
-
-	if (OTHERS_REG & 0x80)
-		fclk = get_FCLK();		/* SYNC Mode	*/
-	else
-		fclk = get_PLLCLK(MPLL);	/* ASYNC Mode	*/
-
-	return fclk / (hclkx2_div * pre_div);
-}
-
-/* return UCLK frequency */
-ulong get_UCLK(void)
-{
-	return get_PLLCLK(EPLL);
-}
-
-int print_cpuinfo(void)
-{
-	printf("\nCPU:     S3C6400@%luMHz\n", get_ARMCLK() / 1000000);
-	printf("         Fclk = %luMHz, Hclk = %luMHz, Pclk = %luMHz ",
-	       get_FCLK() / 1000000, get_HCLK() / 1000000,
-	       get_PCLK() / 1000000);
-
-	if (OTHERS_REG & 0x80)
-		printf("(SYNC Mode) \n");
-	else
-		printf("(ASYNC Mode) \n");
-	return 0;
-}
diff --git a/arch/arm/cpu/arm1176/s3c64xx/timer.c b/arch/arm/cpu/arm1176/s3c64xx/timer.c
deleted file mode 100644
index f16a37b..0000000
--- a/arch/arm/cpu/arm1176/s3c64xx/timer.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * (C) Copyright 2003
- * Texas Instruments <www.ti.com>
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger at sysgo.de>
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Alex Zuepke <azu at sysgo.de>
- *
- * (C) Copyright 2002-2004
- * Gary Jennejohn, DENX Software Engineering, <garyj at denx.de>
- *
- * (C) Copyright 2004
- * Philippe Robin, ARM Ltd. <philippe.robin at arm.com>
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/proc-armv/ptrace.h>
-#include <asm/arch/s3c6400.h>
-#include <div64.h>
-
-static ulong timer_load_val;
-
-#define PRESCALER	167
-
-static s3c64xx_timers *s3c64xx_get_base_timers(void)
-{
-	return (s3c64xx_timers *)ELFIN_TIMER_BASE;
-}
-
-/* macro to read the 16 bit timer */
-static inline ulong read_timer(void)
-{
-	s3c64xx_timers *const timers = s3c64xx_get_base_timers();
-
-	return timers->TCNTO4;
-}
-
-/* Internal tick units */
-/* Last decremneter snapshot */
-static unsigned long lastdec;
-/* Monotonic incrementing timer */
-static unsigned long long timestamp;
-
-int timer_init(void)
-{
-	s3c64xx_timers *const timers = s3c64xx_get_base_timers();
-
-	/* use PWM Timer 4 because it has no output */
-	/*
-	 * We use the following scheme for the timer:
-	 * Prescaler is hard fixed at 167, divider at 1/4.
-	 * This gives at PCLK frequency 66MHz approx. 10us ticks
-	 * The timer is set to wrap after 100s, at 66MHz this obviously
-	 * happens after 10,000,000 ticks. A long variable can thus
-	 * keep values up to 40,000s, i.e., 11 hours. This should be
-	 * enough for most uses:-) Possible optimizations: select a
-	 * binary-friendly frequency, e.g., 1ms / 128. Also calculate
-	 * the prescaler automatically for other PCLK frequencies.
-	 */
-	timers->TCFG0 = PRESCALER << 8;
-	if (timer_load_val == 0) {
-		timer_load_val = get_PCLK() / PRESCALER * (100 / 4); /* 100s */
-		timers->TCFG1 = (timers->TCFG1 & ~0xf0000) | 0x20000;
-	}
-
-	/* load value for 10 ms timeout */
-	lastdec = timers->TCNTB4 = timer_load_val;
-	/* auto load, manual update of Timer 4 */
-	timers->TCON = (timers->TCON & ~0x00700000) | TCON_4_AUTO |
-		TCON_4_UPDATE;
-
-	/* auto load, start Timer 4 */
-	timers->TCON = (timers->TCON & ~0x00700000) | TCON_4_AUTO | COUNT_4_ON;
-	timestamp = 0;
-
-	return 0;
-}
-
-/*
- * timer without interrupts
- */
-
-/*
- * This function is derived from PowerPC code (read timebase as long long).
- * On ARM it just returns the timer value.
- */
-unsigned long long get_ticks(void)
-{
-	ulong now = read_timer();
-
-	if (lastdec >= now) {
-		/* normal mode */
-		timestamp += lastdec - now;
-	} else {
-		/* we have an overflow ... */
-		timestamp += lastdec + timer_load_val - now;
-	}
-	lastdec = now;
-
-	return timestamp;
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk(void)
-{
-	/* We overrun in 100s */
-	return (ulong)(timer_load_val / 100);
-}
-
-ulong get_timer_masked(void)
-{
-	unsigned long long res = get_ticks();
-	do_div (res, (timer_load_val / (100 * CONFIG_SYS_HZ)));
-	return res;
-}
-
-ulong get_timer(ulong base)
-{
-	return get_timer_masked() - base;
-}
-
-void __udelay(unsigned long usec)
-{
-	unsigned long long tmp;
-	ulong tmo;
-
-	tmo = (usec + 9) / 10;
-	tmp = get_ticks() + tmo;	/* get current timestamp */
-
-	while (get_ticks() < tmp)/* loop till event */
-		 /*NOP*/;
-}
diff --git a/arch/arm/include/asm/arch-s3c64xx/hardware.h b/arch/arm/include/asm/arch-s3c64xx/hardware.h
deleted file mode 100644
index 84d24c9..0000000
--- a/arch/arm/include/asm/arch-s3c64xx/hardware.h
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * Originates from Samsung's u-boot 1.1.6 port to S3C6400 / SMDK6400
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _ARCH_HARDWARE_H_
-#define _ARCH_HARDWARE_H_
-
-#include <asm/sizes.h>
-
-#ifndef __ASSEMBLY__
-#define UData(Data)	((unsigned long) (Data))
-
-#define __REG(x)	(*(vu_long *)(x))
-#define __REGl(x)	(*(vu_long *)(x))
-#define __REGw(x)	(*(vu_short *)(x))
-#define __REGb(x)	(*(vu_char *)(x))
-#define __REG2(x, y)	(*(vu_long *)((x) + (y)))
-#else
-#define UData(Data)	(Data)
-
-#define __REG(x)	(x)
-#define __REGl(x)	(x)
-#define __REGw(x)	(x)
-#define __REGb(x)	(x)
-#define __REG2(x, y)	((x) + (y))
-#endif
-
-#define Fld(Size, Shft)	(((Size) << 16) + (Shft))
-
-#define FSize(Field)	((Field) >> 16)
-#define FShft(Field)	((Field) & 0x0000FFFF)
-#define FMsk(Field)	(((UData (1) << FSize (Field)) - 1) << FShft (Field))
-#define FAlnMsk(Field)	((UData (1) << FSize (Field)) - 1)
-#define F1stBit(Field)	(UData (1) << FShft (Field))
-
-#define FClrBit(Data, Bit)	(Data = (Data & ~(Bit)))
-#define FClrFld(Data, Field)	(Data = (Data & ~FMsk(Field)))
-
-#define FInsrt(Value, Field) \
-			(UData (Value) << FShft (Field))
-
-#define FExtr(Data, Field) \
-			((UData (Data) >> FShft (Field)) & FAlnMsk (Field))
-
-#endif /* _ARCH_HARDWARE_H_ */
diff --git a/arch/arm/include/asm/arch-s3c64xx/s3c6400.h b/arch/arm/include/asm/arch-s3c64xx/s3c6400.h
deleted file mode 100644
index 10b3324..0000000
--- a/arch/arm/include/asm/arch-s3c64xx/s3c6400.h
+++ /dev/null
@@ -1,895 +0,0 @@
-/*
- * (C) Copyright 2007
- * Byungjae Lee, Samsung Erectronics, bjlee at samsung.com.
- *      - only support for S3C6400
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************
- * NAME	    : s3c6400.h
- *
- * Based on S3C6400 User's manual Rev 0.0
- ************************************************/
-
-#ifndef __S3C6400_H__
-#define __S3C6400_H__
-
-#define S3C64XX_UART_CHANNELS	3
-#define S3C64XX_SPI_CHANNELS	2
-
-#include <asm/hardware.h>
-
-#define ELFIN_CLOCK_POWER_BASE	0x7e00f000
-
-/* Clock & Power Controller for mDirac3*/
-#define APLL_LOCK_OFFSET	0x00
-#define MPLL_LOCK_OFFSET	0x04
-#define EPLL_LOCK_OFFSET	0x08
-#define APLL_CON_OFFSET		0x0C
-#define MPLL_CON_OFFSET		0x10
-#define EPLL_CON0_OFFSET	0x14
-#define EPLL_CON1_OFFSET	0x18
-#define CLK_SRC_OFFSET		0x1C
-#define CLK_DIV0_OFFSET		0x20
-#define CLK_DIV1_OFFSET		0x24
-#define CLK_DIV2_OFFSET		0x28
-#define CLK_OUT_OFFSET		0x2C
-#define HCLK_GATE_OFFSET	0x30
-#define PCLK_GATE_OFFSET	0x34
-#define SCLK_GATE_OFFSET	0x38
-#define AHB_CON0_OFFSET		0x100
-#define AHB_CON1_OFFSET		0x104
-#define AHB_CON2_OFFSET		0x108
-#define SELECT_DMA_OFFSET	0x110
-#define SW_RST_OFFSET		0x114
-#define SYS_ID_OFFSET		0x118
-#define MEM_SYS_CFG_OFFSET	0x120
-#define QOS_OVERRIDE0_OFFSET	0x124
-#define QOS_OVERRIDE1_OFFSET	0x128
-#define MEM_CFG_STAT_OFFSET	0x12C
-#define PWR_CFG_OFFSET		0x804
-#define EINT_MASK_OFFSET	0x808
-#define NOR_CFG_OFFSET		0x810
-#define STOP_CFG_OFFSET		0x814
-#define SLEEP_CFG_OFFSET	0x818
-#define OSC_FREQ_OFFSET		0x820
-#define OSC_STABLE_OFFSET	0x824
-#define PWR_STABLE_OFFSET	0x828
-#define FPC_STABLE_OFFSET	0x82C
-#define MTC_STABLE_OFFSET	0x830
-#define OTHERS_OFFSET		0x900
-#define RST_STAT_OFFSET		0x904
-#define WAKEUP_STAT_OFFSET	0x908
-#define BLK_PWR_STAT_OFFSET	0x90C
-#define INF_REG0_OFFSET		0xA00
-#define INF_REG1_OFFSET		0xA04
-#define INF_REG2_OFFSET		0xA08
-#define INF_REG3_OFFSET		0xA0C
-#define INF_REG4_OFFSET		0xA10
-#define INF_REG5_OFFSET		0xA14
-#define INF_REG6_OFFSET		0xA18
-#define INF_REG7_OFFSET		0xA1C
-
-#define OSC_CNT_VAL_OFFSET	0x824
-#define PWR_CNT_VAL_OFFSET	0x828
-#define FPC_CNT_VAL_OFFSET	0x82C
-#define MTC_CNT_VAL_OFFSET	0x830
-
-#define APLL_LOCK_REG		__REG(ELFIN_CLOCK_POWER_BASE + APLL_LOCK_OFFSET)
-#define MPLL_LOCK_REG		__REG(ELFIN_CLOCK_POWER_BASE + MPLL_LOCK_OFFSET)
-#define EPLL_LOCK_REG		__REG(ELFIN_CLOCK_POWER_BASE + EPLL_LOCK_OFFSET)
-#define APLL_CON_REG		__REG(ELFIN_CLOCK_POWER_BASE + APLL_CON_OFFSET)
-#define MPLL_CON_REG		__REG(ELFIN_CLOCK_POWER_BASE + MPLL_CON_OFFSET)
-#define EPLL_CON0_REG		__REG(ELFIN_CLOCK_POWER_BASE + EPLL_CON0_OFFSET)
-#define EPLL_CON1_REG		__REG(ELFIN_CLOCK_POWER_BASE + EPLL_CON1_OFFSET)
-#define CLK_SRC_REG		__REG(ELFIN_CLOCK_POWER_BASE + CLK_SRC_OFFSET)
-#define CLK_DIV0_REG		__REG(ELFIN_CLOCK_POWER_BASE + CLK_DIV0_OFFSET)
-#define CLK_DIV1_REG		__REG(ELFIN_CLOCK_POWER_BASE + CLK_DIV1_OFFSET)
-#define CLK_DIV2_REG		__REG(ELFIN_CLOCK_POWER_BASE + CLK_DIV2_OFFSET)
-#define CLK_OUT_REG		__REG(ELFIN_CLOCK_POWER_BASE + CLK_OUT_OFFSET)
-#define HCLK_GATE_REG		__REG(ELFIN_CLOCK_POWER_BASE + HCLK_GATE_OFFSET)
-#define PCLK_GATE_REG		__REG(ELFIN_CLOCK_POWER_BASE + PCLK_GATE_OFFSET)
-#define SCLK_GATE_REG		__REG(ELFIN_CLOCK_POWER_BASE + SCLK_GATE_OFFSET)
-#define AHB_CON0_REG		__REG(ELFIN_CLOCK_POWER_BASE + AHB_CON0_OFFSET)
-#define AHB_CON1_REG		__REG(ELFIN_CLOCK_POWER_BASE + AHB_CON1_OFFSET)
-#define AHB_CON2_REG		__REG(ELFIN_CLOCK_POWER_BASE + AHB_CON2_OFFSET)
-#define SELECT_DMA_REG		__REG(ELFIN_CLOCK_POWER_BASE + \
-				      SELECT_DMA_OFFSET)
-#define SW_RST_REG		__REG(ELFIN_CLOCK_POWER_BASE + SW_RST_OFFSET)
-#define SYS_ID_REG		__REG(ELFIN_CLOCK_POWER_BASE + SYS_ID_OFFSET)
-#define MEM_SYS_CFG_REG		__REG(ELFIN_CLOCK_POWER_BASE + \
-				      MEM_SYS_CFG_OFFSET)
-#define QOS_OVERRIDE0_REG	__REG(ELFIN_CLOCK_POWER_BASE + \
-				      QOS_OVERRIDE0_OFFSET)
-#define QOS_OVERRIDE1_REG	__REG(ELFIN_CLOCK_POWER_BASE + \
-				      QOS_OVERRIDE1_OFFSET)
-#define MEM_CFG_STAT_REG	__REG(ELFIN_CLOCK_POWER_BASE + \
-				      MEM_CFG_STAT_OFFSET)
-#define PWR_CFG_REG		__REG(ELFIN_CLOCK_POWER_BASE + PWR_CFG_OFFSET)
-#define EINT_MASK_REG		__REG(ELFIN_CLOCK_POWER_BASE + EINT_MASK_OFFSET)
-#define NOR_CFG_REG		__REG(ELFIN_CLOCK_POWER_BASE + NOR_CFG_OFFSET)
-#define STOP_CFG_REG		__REG(ELFIN_CLOCK_POWER_BASE + STOP_CFG_OFFSET)
-#define SLEEP_CFG_REG		__REG(ELFIN_CLOCK_POWER_BASE + SLEEP_CFG_OFFSET)
-#define OSC_FREQ_REG		__REG(ELFIN_CLOCK_POWER_BASE + OSC_FREQ_OFFSET)
-#define OSC_CNT_VAL_REG		__REG(ELFIN_CLOCK_POWER_BASE + \
-				      OSC_CNT_VAL_OFFSET)
-#define PWR_CNT_VAL_REG		__REG(ELFIN_CLOCK_POWER_BASE + \
-				      PWR_CNT_VAL_OFFSET)
-#define FPC_CNT_VAL_REG		__REG(ELFIN_CLOCK_POWER_BASE + \
-				      FPC_CNT_VAL_OFFSET)
-#define MTC_CNT_VAL_REG		__REG(ELFIN_CLOCK_POWER_BASE + \
-				      MTC_CNT_VAL_OFFSET)
-#define OTHERS_REG		__REG(ELFIN_CLOCK_POWER_BASE + OTHERS_OFFSET)
-#define RST_STAT_REG		__REG(ELFIN_CLOCK_POWER_BASE + RST_STAT_OFFSET)
-#define WAKEUP_STAT_REG		__REG(ELFIN_CLOCK_POWER_BASE + \
-				      WAKEUP_STAT_OFFSET)
-#define BLK_PWR_STAT_REG	__REG(ELFIN_CLOCK_POWER_BASE + \
-				      BLK_PWR_STAT_OFFSET)
-#define INF_REG0_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG0_OFFSET)
-#define INF_REG1_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG1_OFFSET)
-#define INF_REG2_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG2_OFFSET)
-#define INF_REG3_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG3_OFFSET)
-#define INF_REG4_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG4_OFFSET)
-#define INF_REG5_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG5_OFFSET)
-#define INF_REG6_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG6_OFFSET)
-#define INF_REG7_REG		__REG(ELFIN_CLOCK_POWER_BASE + INF_REG7_OFFSET)
-
-#define APLL_LOCK	(ELFIN_CLOCK_POWER_BASE + APLL_LOCK_OFFSET)
-#define MPLL_LOCK	(ELFIN_CLOCK_POWER_BASE + MPLL_LOCK_OFFSET)
-#define EPLL_LOCK	(ELFIN_CLOCK_POWER_BASE + EPLL_LOCK_OFFSET)
-#define APLL_CON	(ELFIN_CLOCK_POWER_BASE + APLL_CON_OFFSET)
-#define MPLL_CON	(ELFIN_CLOCK_POWER_BASE + MPLL_CON_OFFSET)
-#define EPLL_CON0	(ELFIN_CLOCK_POWER_BASE + EPLL_CON0_OFFSET)
-#define EPLL_CON1	(ELFIN_CLOCK_POWER_BASE + EPLL_CON1_OFFSET)
-#define CLK_SRC		(ELFIN_CLOCK_POWER_BASE + CLK_SRC_OFFSET)
-#define CLK_DIV0	(ELFIN_CLOCK_POWER_BASE + CLK_DIV0_OFFSET)
-#define CLK_DIV1	(ELFIN_CLOCK_POWER_BASE + CLK_DIV1_OFFSET)
-#define CLK_DIV2	(ELFIN_CLOCK_POWER_BASE + CLK_DIV2_OFFSET)
-#define CLK_OUT		(ELFIN_CLOCK_POWER_BASE + CLK_OUT_OFFSET)
-#define HCLK_GATE	(ELFIN_CLOCK_POWER_BASE + HCLK_GATE_OFFSET)
-#define PCLK_GATE	(ELFIN_CLOCK_POWER_BASE + PCLK_GATE_OFFSET)
-#define SCLK_GATE	(ELFIN_CLOCK_POWER_BASE + SCLK_GATE_OFFSET)
-#define AHB_CON0	(ELFIN_CLOCK_POWER_BASE + AHB_CON0_OFFSET)
-#define AHB_CON1	(ELFIN_CLOCK_POWER_BASE + AHB_CON1_OFFSET)
-#define AHB_CON2	(ELFIN_CLOCK_POWER_BASE + AHB_CON2_OFFSET)
-#define SELECT_DMA	(ELFIN_CLOCK_POWER_BASE + SELECT_DMA_OFFSET)
-#define SW_RST		(ELFIN_CLOCK_POWER_BASE + SW_RST_OFFSET)
-#define SYS_ID		(ELFIN_CLOCK_POWER_BASE + SYS_ID_OFFSET)
-#define MEM_SYS_CFG	(ELFIN_CLOCK_POWER_BASE + MEM_SYS_CFG_OFFSET)
-#define QOS_OVERRIDE0	(ELFIN_CLOCK_POWER_BASE + QOS_OVERRIDE0_OFFSET)
-#define QOS_OVERRIDE1	(ELFIN_CLOCK_POWER_BASE + QOS_OVERRIDE1_OFFSET)
-#define MEM_CFG_STAT	(ELFIN_CLOCK_POWER_BASE + MEM_CFG_STAT_OFFSET)
-#define PWR_CFG		(ELFIN_CLOCK_POWER_BASE + PWR_CFG_OFFSET)
-#define EINT_MASK	(ELFIN_CLOCK_POWER_BASE + EINT_MASK_OFFSET)
-#define NOR_CFG		(ELFIN_CLOCK_POWER_BASE + NOR_CFG_OFFSET)
-#define STOP_CFG	(ELFIN_CLOCK_POWER_BASE + STOP_CFG_OFFSET)
-#define SLEEP_CFG	(ELFIN_CLOCK_POWER_BASE + SLEEP_CFG_OFFSET)
-#define OSC_FREQ	(ELFIN_CLOCK_POWER_BASE + OSC_FREQ_OFFSET)
-#define OSC_CNT_VAL	(ELFIN_CLOCK_POWER_BASE + OSC_CNT_VAL_OFFSET)
-#define PWR_CNT_VAL	(ELFIN_CLOCK_POWER_BASE + PWR_CNT_VAL_OFFSET)
-#define FPC_CNT_VAL	(ELFIN_CLOCK_POWER_BASE + FPC_CNT_VAL_OFFSET)
-#define MTC_CNT_VAL	(ELFIN_CLOCK_POWER_BASE + MTC_CNT_VAL_OFFSET)
-#define OTHERS		(ELFIN_CLOCK_POWER_BASE + OTHERS_OFFSET)
-#define RST_STAT	(ELFIN_CLOCK_POWER_BASE + RST_STAT_OFFSET)
-#define WAKEUP_STAT	(ELFIN_CLOCK_POWER_BASE + WAKEUP_STAT_OFFSET)
-#define BLK_PWR_STAT	(ELFIN_CLOCK_POWER_BASE + BLK_PWR_STAT_OFFSET)
-#define INF_REG0	(ELFIN_CLOCK_POWER_BASE + INF_REG0_OFFSET)
-#define INF_REG1	(ELFIN_CLOCK_POWER_BASE + INF_REG1_OFFSET)
-#define INF_REG2	(ELFIN_CLOCK_POWER_BASE + INF_REG2_OFFSET)
-#define INF_REG3	(ELFIN_CLOCK_POWER_BASE + INF_REG3_OFFSET)
-#define INF_REG4	(ELFIN_CLOCK_POWER_BASE + INF_REG4_OFFSET)
-#define INF_REG5	(ELFIN_CLOCK_POWER_BASE + INF_REG5_OFFSET)
-#define INF_REG6	(ELFIN_CLOCK_POWER_BASE + INF_REG6_OFFSET)
-#define INF_REG7	(ELFIN_CLOCK_POWER_BASE + INF_REG7_OFFSET)
-
-
-/*
- * GPIO
- */
-#define ELFIN_GPIO_BASE		0x7f008000
-
-#define GPACON_OFFSET		0x00
-#define GPADAT_OFFSET		0x04
-#define GPAPUD_OFFSET		0x08
-#define GPACONSLP_OFFSET	0x0C
-#define GPAPUDSLP_OFFSET	0x10
-#define GPBCON_OFFSET		0x20
-#define GPBDAT_OFFSET		0x24
-#define GPBPUD_OFFSET		0x28
-#define GPBCONSLP_OFFSET	0x2C
-#define GPBPUDSLP_OFFSET	0x30
-#define GPCCON_OFFSET		0x40
-#define GPCDAT_OFFSET		0x44
-#define GPCPUD_OFFSET		0x48
-#define GPCCONSLP_OFFSET	0x4C
-#define GPCPUDSLP_OFFSET	0x50
-#define GPDCON_OFFSET		0x60
-#define GPDDAT_OFFSET		0x64
-#define GPDPUD_OFFSET		0x68
-#define GPDCONSLP_OFFSET	0x6C
-#define GPDPUDSLP_OFFSET	0x70
-#define GPECON_OFFSET		0x80
-#define GPEDAT_OFFSET		0x84
-#define GPEPUD_OFFSET		0x88
-#define GPECONSLP_OFFSET	0x8C
-#define GPEPUDSLP_OFFSET	0x90
-#define GPFCON_OFFSET		0xA0
-#define GPFDAT_OFFSET		0xA4
-#define GPFPUD_OFFSET		0xA8
-#define GPFCONSLP_OFFSET	0xAC
-#define GPFPUDSLP_OFFSET	0xB0
-#define GPGCON_OFFSET		0xC0
-#define GPGDAT_OFFSET		0xC4
-#define GPGPUD_OFFSET		0xC8
-#define GPGCONSLP_OFFSET	0xCC
-#define GPGPUDSLP_OFFSET	0xD0
-#define GPHCON0_OFFSET		0xE0
-#define GPHCON1_OFFSET		0xE4
-#define GPHDAT_OFFSET		0xE8
-#define GPHPUD_OFFSET		0xEC
-#define GPHCONSLP_OFFSET	0xF0
-#define GPHPUDSLP_OFFSET	0xF4
-#define GPICON_OFFSET		0x100
-#define GPIDAT_OFFSET		0x104
-#define GPIPUD_OFFSET		0x108
-#define GPICONSLP_OFFSET	0x10C
-#define GPIPUDSLP_OFFSET	0x110
-#define GPJCON_OFFSET		0x120
-#define GPJDAT_OFFSET		0x124
-#define GPJPUD_OFFSET		0x128
-#define GPJCONSLP_OFFSET	0x12C
-#define GPJPUDSLP_OFFSET	0x130
-#define MEM0DRVCON_OFFSET	0x1D0
-#define MEM1DRVCON_OFFSET	0x1D4
-#define GPKCON0_OFFSET		0x800
-#define GPKCON1_OFFSET		0x804
-#define GPKDAT_OFFSET		0x808
-#define GPKPUD_OFFSET		0x80C
-#define GPLCON0_OFFSET		0x810
-#define GPLCON1_OFFSET		0x814
-#define GPLDAT_OFFSET		0x818
-#define GPLPUD_OFFSET		0x81C
-#define GPMCON_OFFSET		0x820
-#define GPMDAT_OFFSET		0x824
-#define GPMPUD_OFFSET		0x828
-#define GPNCON_OFFSET		0x830
-#define GPNDAT_OFFSET		0x834
-#define GPNPUD_OFFSET		0x838
-#define GPOCON_OFFSET		0x140
-#define GPODAT_OFFSET		0x144
-#define GPOPUD_OFFSET		0x148
-#define GPOCONSLP_OFFSET	0x14C
-#define GPOPUDSLP_OFFSET	0x150
-#define GPPCON_OFFSET		0x160
-#define GPPDAT_OFFSET		0x164
-#define GPPPUD_OFFSET		0x168
-#define GPPCONSLP_OFFSET	0x16C
-#define GPPPUDSLP_OFFSET	0x170
-#define GPQCON_OFFSET		0x180
-#define GPQDAT_OFFSET		0x184
-#define GPQPUD_OFFSET		0x188
-#define GPQCONSLP_OFFSET	0x18C
-#define GPQPUDSLP_OFFSET	0x190
-
-#define EINTPEND_OFFSET		0x924
-
-#define GPACON_REG		__REG(ELFIN_GPIO_BASE + GPACON_OFFSET)
-#define GPADAT_REG		__REG(ELFIN_GPIO_BASE + GPADAT_OFFSET)
-#define GPAPUD_REG		__REG(ELFIN_GPIO_BASE + GPAPUD_OFFSET)
-#define GPACONSLP_REG		__REG(ELFIN_GPIO_BASE + GPACONSLP_OFFSET)
-#define GPAPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPAPUDSLP_OFFSET)
-#define GPBCON_REG		__REG(ELFIN_GPIO_BASE + GPBCON_OFFSET)
-#define GPBDAT_REG		__REG(ELFIN_GPIO_BASE + GPBDAT_OFFSET)
-#define GPBPUD_REG		__REG(ELFIN_GPIO_BASE + GPBPUD_OFFSET)
-#define GPBCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPBCONSLP_OFFSET)
-#define GPBPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPBPUDSLP_OFFSET)
-#define GPCCON_REG		__REG(ELFIN_GPIO_BASE + GPCCON_OFFSET)
-#define GPCDAT_REG		__REG(ELFIN_GPIO_BASE + GPCDAT_OFFSET)
-#define GPCPUD_REG		__REG(ELFIN_GPIO_BASE + GPCPUD_OFFSET)
-#define GPCCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPCCONSLP_OFFSET)
-#define GPCPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPCPUDSLP_OFFSET)
-#define GPDCON_REG		__REG(ELFIN_GPIO_BASE + GPDCON_OFFSET)
-#define GPDDAT_REG		__REG(ELFIN_GPIO_BASE + GPDDAT_OFFSET)
-#define GPDPUD_REG		__REG(ELFIN_GPIO_BASE + GPDPUD_OFFSET)
-#define GPDCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPDCONSLP_OFFSET)
-#define GPDPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPDPUDSLP_OFFSET)
-#define GPECON_REG		__REG(ELFIN_GPIO_BASE + GPECON_OFFSET)
-#define GPEDAT_REG		__REG(ELFIN_GPIO_BASE + GPEDAT_OFFSET)
-#define GPEPUD_REG		__REG(ELFIN_GPIO_BASE + GPEPUD_OFFSET)
-#define GPECONSLP_REG		__REG(ELFIN_GPIO_BASE + GPECONSLP_OFFSET)
-#define GPEPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPEPUDSLP_OFFSET)
-#define GPFCON_REG		__REG(ELFIN_GPIO_BASE + GPFCON_OFFSET)
-#define GPFDAT_REG		__REG(ELFIN_GPIO_BASE + GPFDAT_OFFSET)
-#define GPFPUD_REG		__REG(ELFIN_GPIO_BASE + GPFPUD_OFFSET)
-#define GPFCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPFCONSLP_OFFSET)
-#define GPFPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPFPUDSLP_OFFSET)
-#define GPGCON_REG		__REG(ELFIN_GPIO_BASE + GPGCON_OFFSET)
-#define GPGDAT_REG		__REG(ELFIN_GPIO_BASE + GPGDAT_OFFSET)
-#define GPGPUD_REG		__REG(ELFIN_GPIO_BASE + GPGPUD_OFFSET)
-#define GPGCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPGCONSLP_OFFSET)
-#define GPGPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPGPUDSLP_OFFSET)
-#define GPHCON0_REG		__REG(ELFIN_GPIO_BASE + GPHCON0_OFFSET)
-#define GPHCON1_REG		__REG(ELFIN_GPIO_BASE + GPHCON1_OFFSET)
-#define GPHDAT_REG		__REG(ELFIN_GPIO_BASE + GPHDAT_OFFSET)
-#define GPHPUD_REG		__REG(ELFIN_GPIO_BASE + GPHPUD_OFFSET)
-#define GPHCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPHCONSLP_OFFSET)
-#define GPHPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPHPUDSLP_OFFSET)
-#define GPICON_REG		__REG(ELFIN_GPIO_BASE + GPICON_OFFSET)
-#define GPIDAT_REG		__REG(ELFIN_GPIO_BASE + GPIDAT_OFFSET)
-#define GPIPUD_REG		__REG(ELFIN_GPIO_BASE + GPIPUD_OFFSET)
-#define GPICONSLP_REG		__REG(ELFIN_GPIO_BASE + GPICONSLP_OFFSET)
-#define GPIPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPIPUDSLP_OFFSET)
-#define GPJCON_REG		__REG(ELFIN_GPIO_BASE + GPJCON_OFFSET)
-#define GPJDAT_REG		__REG(ELFIN_GPIO_BASE + GPJDAT_OFFSET)
-#define GPJPUD_REG		__REG(ELFIN_GPIO_BASE + GPJPUD_OFFSET)
-#define GPJCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPJCONSLP_OFFSET)
-#define GPJPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPJPUDSLP_OFFSET)
-#define GPKCON0_REG		__REG(ELFIN_GPIO_BASE + GPKCON0_OFFSET)
-#define GPKCON1_REG		__REG(ELFIN_GPIO_BASE + GPKCON1_OFFSET)
-#define GPKDAT_REG		__REG(ELFIN_GPIO_BASE + GPKDAT_OFFSET)
-#define GPKPUD_REG		__REG(ELFIN_GPIO_BASE + GPKPUD_OFFSET)
-#define GPLCON0_REG		__REG(ELFIN_GPIO_BASE + GPLCON0_OFFSET)
-#define GPLCON1_REG		__REG(ELFIN_GPIO_BASE + GPLCON1_OFFSET)
-#define GPLDAT_REG		__REG(ELFIN_GPIO_BASE + GPLDAT_OFFSET)
-#define GPLPUD_REG		__REG(ELFIN_GPIO_BASE + GPLPUD_OFFSET)
-#define GPMCON_REG		__REG(ELFIN_GPIO_BASE + GPMCON_OFFSET)
-#define GPMDAT_REG		__REG(ELFIN_GPIO_BASE + GPMDAT_OFFSET)
-#define GPMPUD_REG		__REG(ELFIN_GPIO_BASE + GPMPUD_OFFSET)
-#define GPNCON_REG		__REG(ELFIN_GPIO_BASE + GPNCON_OFFSET)
-#define GPNDAT_REG		__REG(ELFIN_GPIO_BASE + GPNDAT_OFFSET)
-#define GPNPUD_REG		__REG(ELFIN_GPIO_BASE + GPNPUD_OFFSET)
-#define GPOCON_REG		__REG(ELFIN_GPIO_BASE + GPOCON_OFFSET)
-#define GPODAT_REG		__REG(ELFIN_GPIO_BASE + GPODAT_OFFSET)
-#define GPOPUD_REG		__REG(ELFIN_GPIO_BASE + GPOPUD_OFFSET)
-#define GPOCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPOCONSLP_OFFSET)
-#define GPOPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPOPUDSLP_OFFSET)
-#define GPPCON_REG		__REG(ELFIN_GPIO_BASE + GPPCON_OFFSET)
-#define GPPDAT_REG		__REG(ELFIN_GPIO_BASE + GPPDAT_OFFSET)
-#define GPPPUD_REG		__REG(ELFIN_GPIO_BASE + GPPPUD_OFFSET)
-#define GPPCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPPCONSLP_OFFSET)
-#define GPPPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPPPUDSLP_OFFSET)
-#define GPQCON_REG		__REG(ELFIN_GPIO_BASE + GPQCON_OFFSET)
-#define GPQDAT_REG		__REG(ELFIN_GPIO_BASE + GPQDAT_OFFSET)
-#define GPQPUD_REG		__REG(ELFIN_GPIO_BASE + GPQPUD_OFFSET)
-#define GPQCONSLP_REG		__REG(ELFIN_GPIO_BASE + GPQCONSLP_OFFSET)
-#define GPQPUDSLP_REG		__REG(ELFIN_GPIO_BASE + GPQPUDSLP_OFFSET)
-
-/*
- * Bus Matrix
- */
-#define ELFIN_MEM_SYS_CFG	0x7e00f120
-
-#define S3C64XX_MEM_SYS_CFG_16BIT	(1 << 12)
-
-#define S3C64XX_MEM_SYS_CFG_NAND	0x0008
-#define S3C64XX_MEM_SYS_CFG_ONENAND	S3C64XX_MEM_SYS_CFG_16BIT
-
-#define GPACON		(ELFIN_GPIO_BASE + GPACON_OFFSET)
-#define GPADAT		(ELFIN_GPIO_BASE + GPADAT_OFFSET)
-#define GPAPUD		(ELFIN_GPIO_BASE + GPAPUD_OFFSET)
-#define GPACONSLP	(ELFIN_GPIO_BASE + GPACONSLP_OFFSET)
-#define GPAPUDSLP	(ELFIN_GPIO_BASE + GPAPUDSLP_OFFSET)
-#define GPBCON		(ELFIN_GPIO_BASE + GPBCON_OFFSET)
-#define GPBDAT		(ELFIN_GPIO_BASE + GPBDAT_OFFSET)
-#define GPBPUD		(ELFIN_GPIO_BASE + GPBPUD_OFFSET)
-#define GPBCONSLP	(ELFIN_GPIO_BASE + GPBCONSLP_OFFSET)
-#define GPBPUDSLP	(ELFIN_GPIO_BASE + GPBPUDSLP_OFFSET)
-#define GPCCON		(ELFIN_GPIO_BASE + GPCCON_OFFSET)
-#define GPCDAT		(ELFIN_GPIO_BASE + GPCDAT_OFFSET)
-#define GPCPUD		(ELFIN_GPIO_BASE + GPCPUD_OFFSET)
-#define GPCCONSLP	(ELFIN_GPIO_BASE + GPCCONSLP_OFFSET)
-#define GPCPUDSLP	(ELFIN_GPIO_BASE + GPCPUDSLP_OFFSET)
-#define GPDCON		(ELFIN_GPIO_BASE + GPDCON_OFFSET)
-#define GPDDAT		(ELFIN_GPIO_BASE + GPDDAT_OFFSET)
-#define GPDPUD		(ELFIN_GPIO_BASE + GPDPUD_OFFSET)
-#define GPDCONSLP	(ELFIN_GPIO_BASE + GPDCONSLP_OFFSET)
-#define GPDPUDSLP	(ELFIN_GPIO_BASE + GPDPUDSLP_OFFSET)
-#define GPECON		(ELFIN_GPIO_BASE + GPECON_OFFSET)
-#define GPEDAT		(ELFIN_GPIO_BASE + GPEDAT_OFFSET)
-#define GPEPUD		(ELFIN_GPIO_BASE + GPEPUD_OFFSET)
-#define GPECONSLP	(ELFIN_GPIO_BASE + GPECONSLP_OFFSET)
-#define GPEPUDSLP	(ELFIN_GPIO_BASE + GPEPUDSLP_OFFSET)
-#define GPFCON		(ELFIN_GPIO_BASE + GPFCON_OFFSET)
-#define GPFDAT		(ELFIN_GPIO_BASE + GPFDAT_OFFSET)
-#define GPFPUD		(ELFIN_GPIO_BASE + GPFPUD_OFFSET)
-#define GPFCONSLP	(ELFIN_GPIO_BASE + GPFCONSLP_OFFSET)
-#define GPFPUDSLP	(ELFIN_GPIO_BASE + GPFPUDSLP_OFFSET)
-#define GPGCON		(ELFIN_GPIO_BASE + GPGCON_OFFSET)
-#define GPGDAT		(ELFIN_GPIO_BASE + GPGDAT_OFFSET)
-#define GPGPUD		(ELFIN_GPIO_BASE + GPGPUD_OFFSET)
-#define GPGCONSLP	(ELFIN_GPIO_BASE + GPGCONSLP_OFFSET)
-#define GPGPUDSLP	(ELFIN_GPIO_BASE + GPGPUDSLP_OFFSET)
-#define GPHCON0		(ELFIN_GPIO_BASE + GPHCON0_OFFSET)
-#define GPHCON1		(ELFIN_GPIO_BASE + GPHCON1_OFFSET)
-#define GPHDAT		(ELFIN_GPIO_BASE + GPHDAT_OFFSET)
-#define GPHPUD		(ELFIN_GPIO_BASE + GPHPUD_OFFSET)
-#define GPHCONSLP	(ELFIN_GPIO_BASE + GPHCONSLP_OFFSET)
-#define GPHPUDSLP	(ELFIN_GPIO_BASE + GPHPUDSLP_OFFSET)
-#define GPICON		(ELFIN_GPIO_BASE + GPICON_OFFSET)
-#define GPIDAT		(ELFIN_GPIO_BASE + GPIDAT_OFFSET)
-#define GPIPUD		(ELFIN_GPIO_BASE + GPIPUD_OFFSET)
-#define GPICONSLP	(ELFIN_GPIO_BASE + GPICONSLP_OFFSET)
-#define GPIPUDSLP	(ELFIN_GPIO_BASE + GPIPUDSLP_OFFSET)
-#define GPJCON		(ELFIN_GPIO_BASE + GPJCON_OFFSET)
-#define GPJDAT		(ELFIN_GPIO_BASE + GPJDAT_OFFSET)
-#define GPJPUD		(ELFIN_GPIO_BASE + GPJPUD_OFFSET)
-#define GPJCONSLP	(ELFIN_GPIO_BASE + GPJCONSLP_OFFSET)
-#define GPJPUDSLP	(ELFIN_GPIO_BASE + GPJPUDSLP_OFFSET)
-#define GPKCON0		(ELFIN_GPIO_BASE + GPKCON0_OFFSET)
-#define GPKCON1		(ELFIN_GPIO_BASE + GPKCON1_OFFSET)
-#define GPKDAT		(ELFIN_GPIO_BASE + GPKDAT_OFFSET)
-#define GPKPUD		(ELFIN_GPIO_BASE + GPKPUD_OFFSET)
-#define GPLCON0		(ELFIN_GPIO_BASE + GPLCON0_OFFSET)
-#define GPLCON1		(ELFIN_GPIO_BASE + GPLCON1_OFFSET)
-#define GPLDAT		(ELFIN_GPIO_BASE + GPLDAT_OFFSET)
-#define GPLPUD		(ELFIN_GPIO_BASE + GPLPUD_OFFSET)
-#define GPMCON		(ELFIN_GPIO_BASE + GPMCON_OFFSET)
-#define GPMDAT		(ELFIN_GPIO_BASE + GPMDAT_OFFSET)
-#define GPMPUD		(ELFIN_GPIO_BASE + GPMPUD_OFFSET)
-#define GPNCON		(ELFIN_GPIO_BASE + GPNCON_OFFSET)
-#define GPNDAT		(ELFIN_GPIO_BASE + GPNDAT_OFFSET)
-#define GPNPUD		(ELFIN_GPIO_BASE + GPNPUD_OFFSET)
-#define GPOCON		(ELFIN_GPIO_BASE + GPOCON_OFFSET)
-#define GPODAT		(ELFIN_GPIO_BASE + GPODAT_OFFSET)
-#define GPOPUD		(ELFIN_GPIO_BASE + GPOPUD_OFFSET)
-#define GPOCONSLP	(ELFIN_GPIO_BASE + GPOCONSLP_OFFSET)
-#define GPOPUDSLP	(ELFIN_GPIO_BASE + GPOPUDSLP_OFFSET)
-#define GPPCON		(ELFIN_GPIO_BASE + GPPCON_OFFSET)
-#define GPPDAT		(ELFIN_GPIO_BASE + GPPDAT_OFFSET)
-#define GPPPUD		(ELFIN_GPIO_BASE + GPPPUD_OFFSET)
-#define GPPCONSLP	(ELFIN_GPIO_BASE + GPPCONSLP_OFFSET)
-#define GPPPUDSLP	(ELFIN_GPIO_BASE + GPPPUDSLP_OFFSET)
-#define GPQCON		(ELFIN_GPIO_BASE + GPQCON_OFFSET)
-#define GPQDAT		(ELFIN_GPIO_BASE + GPQDAT_OFFSET)
-#define GPQPUD		(ELFIN_GPIO_BASE + GPQPUD_OFFSET)
-#define GPQCONSLP	(ELFIN_GPIO_BASE + GPQCONSLP_OFFSET)
-#define GPQPUDSLP	(ELFIN_GPIO_BASE + GPQPUDSLP_OFFSET)
-
-/*
- * Memory controller
- */
-#define ELFIN_SROM_BASE		0x70000000
-
-#define SROM_BW_REG	__REG(ELFIN_SROM_BASE + 0x0)
-#define SROM_BC0_REG	__REG(ELFIN_SROM_BASE + 0x4)
-#define SROM_BC1_REG	__REG(ELFIN_SROM_BASE + 0x8)
-#define SROM_BC2_REG	__REG(ELFIN_SROM_BASE + 0xC)
-#define SROM_BC3_REG	__REG(ELFIN_SROM_BASE + 0x10)
-#define SROM_BC4_REG	__REG(ELFIN_SROM_BASE + 0x14)
-#define SROM_BC5_REG	__REG(ELFIN_SROM_BASE + 0x18)
-
-/*
- * SDRAM Controller
- */
-#define ELFIN_DMC0_BASE		0x7e000000
-#define ELFIN_DMC1_BASE		0x7e001000
-
-#define INDEX_DMC_MEMC_STATUS	0x00
-#define INDEX_DMC_MEMC_CMD	0x04
-#define INDEX_DMC_DIRECT_CMD	0x08
-#define INDEX_DMC_MEMORY_CFG	0x0C
-#define INDEX_DMC_REFRESH_PRD	0x10
-#define INDEX_DMC_CAS_LATENCY	0x14
-#define INDEX_DMC_T_DQSS	0x18
-#define INDEX_DMC_T_MRD		0x1C
-#define INDEX_DMC_T_RAS		0x20
-#define INDEX_DMC_T_RC		0x24
-#define INDEX_DMC_T_RCD		0x28
-#define INDEX_DMC_T_RFC		0x2C
-#define INDEX_DMC_T_RP		0x30
-#define INDEX_DMC_T_RRD		0x34
-#define INDEX_DMC_T_WR		0x38
-#define INDEX_DMC_T_WTR		0x3C
-#define INDEX_DMC_T_XP		0x40
-#define INDEX_DMC_T_XSR		0x44
-#define INDEX_DMC_T_ESR		0x48
-#define INDEX_DMC_MEMORY_CFG2	0x4C
-#define INDEX_DMC_CHIP_0_CFG	0x200
-#define INDEX_DMC_CHIP_1_CFG	0x204
-#define INDEX_DMC_CHIP_2_CFG	0x208
-#define INDEX_DMC_CHIP_3_CFG	0x20C
-#define INDEX_DMC_USER_STATUS	0x300
-#define INDEX_DMC_USER_CONFIG	0x304
-
-/*
- * Memory Chip direct command
- */
-#define DMC_NOP0	0x0c0000
-#define DMC_NOP1	0x1c0000
-#define DMC_PA0		0x000000	/* Precharge all */
-#define DMC_PA1		0x100000
-#define DMC_AR0		0x040000	/* Autorefresh */
-#define DMC_AR1		0x140000
-#define DMC_SDR_MR0	0x080032	/* MRS, CAS 3,  Burst Length 4 */
-#define DMC_SDR_MR1	0x180032
-#define DMC_DDR_MR0	0x080162
-#define DMC_DDR_MR1	0x180162
-#define DMC_mDDR_MR0	0x080032	/* CAS 3, Burst Length 4 */
-#define DMC_mDDR_MR1	0x180032
-#define DMC_mSDR_EMR0	0x0a0000	/* EMRS, DS:Full, PASR:Full Array */
-#define DMC_mSDR_EMR1	0x1a0000
-#define DMC_DDR_EMR0	0x090000
-#define DMC_DDR_EMR1	0x190000
-#define DMC_mDDR_EMR0	0x0a0000	/*  DS:Full, PASR:Full Array */
-#define DMC_mDDR_EMR1	0x1a0000
-
-/*
- * Definitions for memory configuration
- * Set memory configuration
- *	active_chips	= 1'b0 (1 chip)
- *	qos_master_chip	= 3'b000(ARID[3:0])
- *	memory burst	= 3'b010(burst 4)
- *	stop_mem_clock	= 1'b0(disable dynamical stop)
- *	auto_power_down	= 1'b0(disable auto power-down mode)
- *	power_down_prd	= 6'b00_0000(0 cycle for auto power-down)
- *	ap_bit		= 1'b0 (bit position of auto-precharge is 10)
- *	row_bits	= 3'b010(# row address 13)
- *	column_bits	= 3'b010(# column address 10 )
- *
- * Set user configuration
- *	2'b10=SDRAM/mSDRAM, 2'b11=DDR, 2'b01=mDDR
- *
- * Set chip select for chip [n]
- *	 row bank control, bank address 0x3000_0000 ~ 0x37ff_ffff
- *	 CHIP_[n]_CFG=0x30F8,  30: ADDR[31:24], F8: Mask[31:24]
- */
-
-/*
- * Nand flash controller
- */
-#define ELFIN_NAND_BASE		0x70200000
-
-#define NFCONF_OFFSET		0x00
-#define NFCONT_OFFSET		0x04
-#define NFCMMD_OFFSET		0x08
-#define NFADDR_OFFSET		0x0c
-#define NFDATA_OFFSET		0x10
-#define NFMECCDATA0_OFFSET	0x14
-#define NFMECCDATA1_OFFSET	0x18
-#define NFSECCDATA0_OFFSET	0x1c
-#define NFSBLK_OFFSET		0x20
-#define NFEBLK_OFFSET		0x24
-#define NFSTAT_OFFSET		0x28
-#define NFESTAT0_OFFSET		0x2c
-#define NFESTAT1_OFFSET		0x30
-#define NFMECC0_OFFSET		0x34
-#define NFMECC1_OFFSET		0x38
-#define NFSECC_OFFSET		0x3c
-#define NFMLCBITPT_OFFSET	0x40
-
-#define NFCONF			(ELFIN_NAND_BASE + NFCONF_OFFSET)
-#define NFCONT			(ELFIN_NAND_BASE + NFCONT_OFFSET)
-#define NFCMMD			(ELFIN_NAND_BASE + NFCMMD_OFFSET)
-#define NFADDR			(ELFIN_NAND_BASE + NFADDR_OFFSET)
-#define NFDATA			(ELFIN_NAND_BASE + NFDATA_OFFSET)
-#define NFMECCDATA0		(ELFIN_NAND_BASE + NFMECCDATA0_OFFSET)
-#define NFMECCDATA1		(ELFIN_NAND_BASE + NFMECCDATA1_OFFSET)
-#define NFSECCDATA0		(ELFIN_NAND_BASE + NFSECCDATA0_OFFSET)
-#define NFSBLK			(ELFIN_NAND_BASE + NFSBLK_OFFSET)
-#define NFEBLK			(ELFIN_NAND_BASE + NFEBLK_OFFSET)
-#define NFSTAT			(ELFIN_NAND_BASE + NFSTAT_OFFSET)
-#define NFESTAT0		(ELFIN_NAND_BASE + NFESTAT0_OFFSET)
-#define NFESTAT1		(ELFIN_NAND_BASE + NFESTAT1_OFFSET)
-#define NFMECC0			(ELFIN_NAND_BASE + NFMECC0_OFFSET)
-#define NFMECC1			(ELFIN_NAND_BASE + NFMECC1_OFFSET)
-#define NFSECC			(ELFIN_NAND_BASE + NFSECC_OFFSET)
-#define NFMLCBITPT		(ELFIN_NAND_BASE + NFMLCBITPT_OFFSET)
-
-#define NFCONF_REG		__REG(ELFIN_NAND_BASE + NFCONF_OFFSET)
-#define NFCONT_REG		__REG(ELFIN_NAND_BASE + NFCONT_OFFSET)
-#define NFCMD_REG		__REG(ELFIN_NAND_BASE + NFCMMD_OFFSET)
-#define NFADDR_REG		__REG(ELFIN_NAND_BASE + NFADDR_OFFSET)
-#define NFDATA_REG		__REG(ELFIN_NAND_BASE + NFDATA_OFFSET)
-#define NFDATA8_REG		__REGb(ELFIN_NAND_BASE + NFDATA_OFFSET)
-#define NFMECCDATA0_REG		__REG(ELFIN_NAND_BASE + NFMECCDATA0_OFFSET)
-#define NFMECCDATA1_REG		__REG(ELFIN_NAND_BASE + NFMECCDATA1_OFFSET)
-#define NFSECCDATA0_REG		__REG(ELFIN_NAND_BASE + NFSECCDATA0_OFFSET)
-#define NFSBLK_REG		__REG(ELFIN_NAND_BASE + NFSBLK_OFFSET)
-#define NFEBLK_REG		__REG(ELFIN_NAND_BASE + NFEBLK_OFFSET)
-#define NFSTAT_REG		__REG(ELFIN_NAND_BASE + NFSTAT_OFFSET)
-#define NFESTAT0_REG		__REG(ELFIN_NAND_BASE + NFESTAT0_OFFSET)
-#define NFESTAT1_REG		__REG(ELFIN_NAND_BASE + NFESTAT1_OFFSET)
-#define NFMECC0_REG		__REG(ELFIN_NAND_BASE + NFMECC0_OFFSET)
-#define NFMECC1_REG		__REG(ELFIN_NAND_BASE + NFMECC1_OFFSET)
-#define NFSECC_REG		__REG(ELFIN_NAND_BASE + NFSECC_OFFSET)
-#define NFMLCBITPT_REG		__REG(ELFIN_NAND_BASE + NFMLCBITPT_OFFSET)
-
-#define NFCONF_ECC_4BIT		(1<<24)
-
-#define NFCONT_ECC_ENC		(1<<18)
-#define NFCONT_WP		(1<<16)
-#define NFCONT_MECCLOCK		(1<<7)
-#define NFCONT_SECCLOCK		(1<<6)
-#define NFCONT_INITMECC		(1<<5)
-#define NFCONT_INITSECC		(1<<4)
-#define NFCONT_INITECC		(NFCONT_INITMECC | NFCONT_INITSECC)
-#define NFCONT_CS_ALT		(1<<2)
-#define NFCONT_CS		(1<<1)
-#define NFCONT_ENABLE		(1<<0)
-
-#define NFSTAT_ECCENCDONE	(1<<7)
-#define NFSTAT_ECCDECDONE	(1<<6)
-#define NFSTAT_RnB		(1<<0)
-
-#define NFESTAT0_ECCBUSY	(1<<31)
-
-/*
- * Interrupt
- */
-#define ELFIN_VIC0_BASE_ADDR	0x71200000
-#define ELFIN_VIC1_BASE_ADDR	0x71300000
-#define oINTMOD			0x0C	/* VIC INT SELECT (IRQ or FIQ) */
-#define oINTUNMSK		0x10	/* VIC INT EN (write 1 to unmask) */
-#define oINTMSK			0x14	/* VIC INT EN CLEAR (write 1 to mask) */
-#define oINTSUBMSK		0x1C	/* VIC SOFT INT CLEAR */
-#define oVECTADDR		0xF00 /* VIC ADDRESS */
-
-/*
- * Watchdog timer
- */
-#define ELFIN_WATCHDOG_BASE	0x7E004000
-
-#define WTCON_REG		__REG(0x7E004004)
-#define WTDAT_REG		__REG(0x7E004008)
-#define WTCNT_REG		__REG(0x7E00400C)
-
-
-/*
- * UART
- */
-#define ELFIN_UART_BASE		0x7F005000
-
-#define ELFIN_UART0_OFFSET	0x0000
-#define ELFIN_UART1_OFFSET	0x0400
-#define ELFIN_UART2_OFFSET	0x0800
-
-#define ULCON_OFFSET		0x00
-#define UCON_OFFSET		0x04
-#define UFCON_OFFSET		0x08
-#define UMCON_OFFSET		0x0C
-#define UTRSTAT_OFFSET		0x10
-#define UERSTAT_OFFSET		0x14
-#define UFSTAT_OFFSET		0x18
-#define UMSTAT_OFFSET		0x1C
-#define UTXH_OFFSET		0x20
-#define URXH_OFFSET		0x24
-#define UBRDIV_OFFSET		0x28
-#define UDIVSLOT_OFFSET		0x2C
-#define UINTP_OFFSET		0x30
-#define UINTSP_OFFSET		0x34
-#define UINTM_OFFSET		0x38
-
-#define ULCON0_REG		__REG(0x7F005000)
-#define UCON0_REG		__REG(0x7F005004)
-#define UFCON0_REG		__REG(0x7F005008)
-#define UMCON0_REG		__REG(0x7F00500C)
-#define UTRSTAT0_REG		__REG(0x7F005010)
-#define UERSTAT0_REG		__REG(0x7F005014)
-#define UFSTAT0_REG		__REG(0x7F005018)
-#define UMSTAT0_REG		__REG(0x7F00501c)
-#define UTXH0_REG		__REG(0x7F005020)
-#define URXH0_REG		__REG(0x7F005024)
-#define UBRDIV0_REG		__REG(0x7F005028)
-#define UDIVSLOT0_REG		__REG(0x7F00502c)
-#define UINTP0_REG		__REG(0x7F005030)
-#define UINTSP0_REG		__REG(0x7F005034)
-#define UINTM0_REG		__REG(0x7F005038)
-
-#define ULCON1_REG		__REG(0x7F005400)
-#define UCON1_REG		__REG(0x7F005404)
-#define UFCON1_REG		__REG(0x7F005408)
-#define UMCON1_REG		__REG(0x7F00540C)
-#define UTRSTAT1_REG		__REG(0x7F005410)
-#define UERSTAT1_REG		__REG(0x7F005414)
-#define UFSTAT1_REG		__REG(0x7F005418)
-#define UMSTAT1_REG		__REG(0x7F00541c)
-#define UTXH1_REG		__REG(0x7F005420)
-#define URXH1_REG		__REG(0x7F005424)
-#define UBRDIV1_REG		__REG(0x7F005428)
-#define UDIVSLOT1_REG		__REG(0x7F00542c)
-#define UINTP1_REG		__REG(0x7F005430)
-#define UINTSP1_REG		__REG(0x7F005434)
-#define UINTM1_REG		__REG(0x7F005438)
-
-#define UTRSTAT_TX_EMPTY	(1 << 2)
-#define UTRSTAT_RX_READY	(1 << 0)
-#define UART_ERR_MASK		0xF
-
-/*
- * PWM timer
- */
-#define ELFIN_TIMER_BASE	0x7F006000
-
-#define TCFG0_REG	__REG(0x7F006000)
-#define TCFG1_REG	__REG(0x7F006004)
-#define TCON_REG	__REG(0x7F006008)
-#define TCNTB0_REG	__REG(0x7F00600c)
-#define TCMPB0_REG	__REG(0x7F006010)
-#define TCNTO0_REG	__REG(0x7F006014)
-#define TCNTB1_REG	__REG(0x7F006018)
-#define TCMPB1_REG	__REG(0x7F00601c)
-#define TCNTO1_REG	__REG(0x7F006020)
-#define TCNTB2_REG	__REG(0x7F006024)
-#define TCMPB2_REG	__REG(0x7F006028)
-#define TCNTO2_REG	__REG(0x7F00602c)
-#define TCNTB3_REG	__REG(0x7F006030)
-#define TCMPB3_REG	__REG(0x7F006034)
-#define TCNTO3_REG	__REG(0x7F006038)
-#define TCNTB4_REG	__REG(0x7F00603c)
-#define TCNTO4_REG	__REG(0x7F006040)
-
-/* Fields */
-#define fTCFG0_DZONE		Fld(8, 16) /* the dead zone length (=timer 0) */
-#define fTCFG0_PRE1		Fld(8, 8)  /* prescaler value for time 2,3,4 */
-#define fTCFG0_PRE0		Fld(8, 0)  /* prescaler value for time 0,1 */
-#define fTCFG1_MUX4		Fld(4, 16)
-/* bits */
-#define TCFG0_DZONE(x)		FInsrt((x), fTCFG0_DZONE)
-#define TCFG0_PRE1(x)		FInsrt((x), fTCFG0_PRE1)
-#define TCFG0_PRE0(x)		FInsrt((x), fTCFG0_PRE0)
-#define TCON_4_AUTO		(1 << 22)  /* auto reload on/off for Timer 4 */
-#define TCON_4_UPDATE		(1 << 21)  /* manual Update TCNTB4 */
-#define TCON_4_ONOFF		(1 << 20)  /* 0: Stop, 1: start Timer 4 */
-#define COUNT_4_ON		(TCON_4_ONOFF * 1)
-#define COUNT_4_OFF		(TCON_4_ONOFF * 0)
-#define TCON_3_AUTO		(1 << 19)  /* auto reload on/off for Timer 3 */
-#define TIMER3_ATLOAD_ON	(TCON_3_AUTO * 1)
-#define TIMER3_ATLAOD_OFF	FClrBit(TCON, TCON_3_AUTO)
-#define TCON_3_INVERT		(1 << 18)  /* 1: Inverter on for TOUT3 */
-#define TIMER3_IVT_ON		(TCON_3_INVERT * 1)
-#define TIMER3_IVT_OFF		(FClrBit(TCON, TCON_3_INVERT))
-#define TCON_3_MAN		(1 << 17)  /* manual Update TCNTB3,TCMPB3 */
-#define TIMER3_MANUP		(TCON_3_MAN*1)
-#define TIMER3_NOP		(FClrBit(TCON, TCON_3_MAN))
-#define TCON_3_ONOFF		(1 << 16)  /* 0: Stop, 1: start Timer 3 */
-#define TIMER3_ON		(TCON_3_ONOFF * 1)
-#define TIMER3_OFF		(FClrBit(TCON, TCON_3_ONOFF))
-
-#if defined(CONFIG_CLK_400_100_50)
-#define STARTUP_AMDIV		400
-#define STARTUP_MDIV		400
-#define STARTUP_PDIV		6
-#define STARTUP_SDIV		1
-#elif defined(CONFIG_CLK_400_133_66)
-#define STARTUP_AMDIV		400
-#define STARTUP_MDIV		533
-#define STARTUP_PDIV		6
-#define STARTUP_SDIV		1
-#elif defined(CONFIG_CLK_533_133_66)
-#define STARTUP_AMDIV		533
-#define STARTUP_MDIV		533
-#define STARTUP_PDIV		6
-#define STARTUP_SDIV		1
-#elif defined(CONFIG_CLK_667_133_66)
-#define STARTUP_AMDIV		667
-#define STARTUP_MDIV		533
-#define STARTUP_PDIV		6
-#define STARTUP_SDIV		1
-#endif
-
-#define	STARTUP_PCLKDIV		3
-#define STARTUP_HCLKX2DIV	1
-#define STARTUP_HCLKDIV		1
-#define STARTUP_MPLLDIV		1
-#define STARTUP_APLLDIV		0
-
-#define CLK_DIV_VAL	((STARTUP_PCLKDIV << 12) | (STARTUP_HCLKX2DIV << 9) | \
-	(STARTUP_HCLKDIV << 8) | (STARTUP_MPLLDIV<<4) | STARTUP_APLLDIV)
-#define MPLL_VAL	((1 << 31) | (STARTUP_MDIV << 16) | \
-	(STARTUP_PDIV << 8) | STARTUP_SDIV)
-#define STARTUP_MPLL	(((CONFIG_SYS_CLK_FREQ >> STARTUP_SDIV) / \
-	STARTUP_PDIV) * STARTUP_MDIV)
-
-#if defined(CONFIG_SYNC_MODE)
-#define APLL_VAL	((1 << 31) | (STARTUP_MDIV << 16) | \
-	(STARTUP_PDIV << 8) | STARTUP_SDIV)
-#define STARTUP_APLL	(((CONFIG_SYS_CLK_FREQ >> STARTUP_SDIV) / \
-	STARTUP_PDIV) * STARTUP_MDIV)
-#define STARTUP_HCLK	(STARTUP_MPLL / (STARTUP_HCLKX2DIV + 1) / \
-	(STARTUP_HCLKDIV + 1))
-#else
-#define APLL_VAL	((1 << 31) | (STARTUP_AMDIV << 16) | \
-	(STARTUP_PDIV << 8) | STARTUP_SDIV)
-#define STARTUP_APLL	(((CONFIG_SYS_CLK_FREQ >> STARTUP_SDIV) / \
-	STARTUP_PDIV) * STARTUP_AMDIV)
-#define STARTUP_HCLK	(STARTUP_MPLL / (STARTUP_HCLKX2DIV + 1) / \
-	(STARTUP_HCLKDIV + 1))
-#endif
-
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define DMC1_MEM_CFG	0x00010012	/* burst 4, 13-bit row, 10-bit col */
-#define DMC1_MEM_CFG2	0xB45
-#define DMC1_CHIP0_CFG	0x150F8		/* 0x5000_0000~0x57ff_ffff (128 MiB) */
-#define DMC_DDR_32_CFG	0x0 		/* 32bit, DDR */
-
-/* Memory Parameters */
-/* DDR Parameters */
-#define DDR_tREFRESH		7800	/* ns */
-#define DDR_tRAS		45	/* ns (min: 45ns)*/
-#define DDR_tRC 		68	/* ns (min: 67.5ns)*/
-#define DDR_tRCD		23	/* ns (min: 22.5ns)*/
-#define DDR_tRFC		80	/* ns (min: 80ns)*/
-#define DDR_tRP 		23	/* ns (min: 22.5ns)*/
-#define DDR_tRRD		15	/* ns (min: 15ns)*/
-#define DDR_tWR 		15	/* ns (min: 15ns)*/
-#define DDR_tXSR		120	/* ns (min: 120ns)*/
-#define DDR_CASL		3	/* CAS Latency 3 */
-
-/*
- * mDDR memory configuration
- */
-
-#define NS_TO_CLK(t)		((STARTUP_HCLK / 1000 * (t) - 1) / 1000000)
-
-#define DMC_DDR_BA_EMRS 	2
-#define DMC_DDR_MEM_CASLAT	3
-/* 6   Set Cas Latency to 3 */
-#define DMC_DDR_CAS_LATENCY	(DDR_CASL << 1)
-/* Min 0.75 ~ 1.25 */
-#define DMC_DDR_t_DQSS		1
-/* Min 2 tck */
-#define DMC_DDR_t_MRD		2
-/* 7, Min 45ns */
-#define DMC_DDR_t_RAS		(NS_TO_CLK(DDR_tRAS) + 1)
-/* 10, Min 67.5ns */
-#define DMC_DDR_t_RC		(NS_TO_CLK(DDR_tRC) + 1)
-/* 4,5(TRM), Min 22.5ns */
-#define DMC_DDR_t_RCD		(NS_TO_CLK(DDR_tRCD) + 1)
-#define DMC_DDR_schedule_RCD	((DMC_DDR_t_RCD - 3) << 3)
-/* 11,18(TRM) Min 80ns */
-#define DMC_DDR_t_RFC		(NS_TO_CLK(DDR_tRFC) + 1)
-#define DMC_DDR_schedule_RFC	((DMC_DDR_t_RFC - 3) << 5)
-/* 4, 5(TRM) Min 22.5ns */
-#define DMC_DDR_t_RP		(NS_TO_CLK(DDR_tRP) + 1)
-#define DMC_DDR_schedule_RP	((DMC_DDR_t_RP - 3) << 3)
-/* 3, Min 15ns */
-#define DMC_DDR_t_RRD		(NS_TO_CLK(DDR_tRRD) + 1)
-/* Min 15ns */
-#define DMC_DDR_t_WR		(NS_TO_CLK(DDR_tWR) + 1)
-#define DMC_DDR_t_WTR		2
-/* 1tck + tIS(1.5ns) */
-#define DMC_DDR_t_XP		2
-/* 17, Min 120ns */
-#define DMC_DDR_t_XSR		(NS_TO_CLK(DDR_tXSR) + 1)
-#define DMC_DDR_t_ESR		DMC_DDR_t_XSR
-/* TRM 2656 */
-#define DMC_DDR_REFRESH_PRD	(NS_TO_CLK(DDR_tREFRESH))
-/* 2b01 : mDDR */
-#define DMC_DDR_USER_CONFIG	1
-
-#ifndef __ASSEMBLY__
-enum s3c64xx_uarts_nr {
-	S3C64XX_UART0,
-	S3C64XX_UART1,
-	S3C64XX_UART2,
-};
-
-#include "s3c64x0.h"
-
-static inline s3c64xx_uart *s3c64xx_get_base_uart(enum s3c64xx_uarts_nr nr)
-{
-	return (s3c64xx_uart *)(ELFIN_UART_BASE + (nr * 0x400));
-}
-#endif
-
-#endif /*__S3C6400_H__*/
diff --git a/arch/arm/include/asm/arch-s3c64xx/s3c64x0.h b/arch/arm/include/asm/arch-s3c64xx/s3c64x0.h
deleted file mode 100644
index 0bbf1d0..0000000
--- a/arch/arm/include/asm/arch-s3c64xx/s3c64x0.h
+++ /dev/null
@@ -1,90 +0,0 @@
-/*
- * (C) Copyright 2003
- * David MÃŒller ELSOFT AG Switzerland. d.mueller at elsoft.ch
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************
- * NAME	    : S3C64XX.h
- * Version  : 31.3.2003
- *
- * common stuff for SAMSUNG S3C64XX SoC
- ************************************************/
-
-#ifndef __S3C64XX_H__
-#define __S3C64XX_H__
-
-#if defined(CONFIG_SYNC_MODE) && defined(CONFIG_S3C6400)
-#error CONFIG_SYNC_MODE unavailable on S3C6400, please, fix your configuration!
-#endif
-
-#include <asm/types.h>
-
-/* UART (see manual chapter 11) */
-typedef struct {
-	volatile u32	ULCON;
-	volatile u32	UCON;
-	volatile u32	UFCON;
-	volatile u32	UMCON;
-	volatile u32	UTRSTAT;
-	volatile u32	UERSTAT;
-	volatile u32	UFSTAT;
-	volatile u32	UMSTAT;
-#ifdef __BIG_ENDIAN
-	volatile u8	res1[3];
-	volatile u8	UTXH;
-	volatile u8	res2[3];
-	volatile u8	URXH;
-#else /* Little Endian */
-	volatile u8	UTXH;
-	volatile u8	res1[3];
-	volatile u8	URXH;
-	volatile u8	res2[3];
-#endif
-	volatile u32	UBRDIV;
-#ifdef __BIG_ENDIAN
-	volatile u8	res3[2];
-	volatile u16	UDIVSLOT;
-#else
-	volatile u16	UDIVSLOT;
-	volatile u8	res3[2];
-#endif
-} s3c64xx_uart;
-
-/* PWM TIMER (see manual chapter 10) */
-typedef struct {
-	volatile u32	TCNTB;
-	volatile u32	TCMPB;
-	volatile u32	TCNTO;
-} s3c64xx_timer;
-
-typedef struct {
-	volatile u32	TCFG0;
-	volatile u32	TCFG1;
-	volatile u32	TCON;
-	s3c64xx_timer	ch[4];
-	volatile u32	TCNTB4;
-	volatile u32	TCNTO4;
-} s3c64xx_timers;
-
-#endif /*__S3C64XX_H__*/
diff --git a/doc/driver-model/UDM-serial.txt b/doc/driver-model/UDM-serial.txt
index ef71fea..1011c32 100644
--- a/doc/driver-model/UDM-serial.txt
+++ b/doc/driver-model/UDM-serial.txt
@@ -96,88 +96,84 @@ III) Analysis of in-tree drivers
   ------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  10) s3c64xx.c
+  10) sandbox.c
   -------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  11) sandbox.c
-  -------------
-  No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
-
-  12) serial.c
+  11) serial.c
   ------------
   This is a complementary part of NS16550 UART driver, see above.
 
-  13) serial_clps7111.c
+  12) serial_clps7111.c
   ---------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  14) serial_imx.c
+  13) serial_imx.c
   ----------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible. This driver
   might be removed in favor of serial_mxc.c .
 
-  15) serial_ixp.c
+  14) serial_ixp.c
   ----------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  16) serial_ks8695.c
+  15) serial_ks8695.c
   -------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  17) serial_max3100.c
+  16) serial_max3100.c
   --------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  18) serial_mxc.c
+  17) serial_mxc.c
   ----------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  19) serial_netarm.c
+  18) serial_netarm.c
   -------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  20) serial_pl01x.c
+  19) serial_pl01x.c
   ------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible, though this
   driver in fact contains two drivers in total.
 
-  21) serial_pxa.c
+  20) serial_pxa.c
   ----------------
   This driver is a bit complicated, but due to clean support for
   CONFIG_SERIAL_MULTI, there are no expected obstructions throughout the
   conversion process.
 
-  22) serial_s3c24x0.c
+  21) serial_s3c24x0.c
   --------------------
   This driver, being quite ad-hoc might need some work to bring back to shape.
 
-  23) serial_s3c44b0.c
+  22) serial_s3c44b0.c
   --------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  24) serial_s5p.c
+  23) serial_s5p.c
   ----------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  25) serial_sa1100.c
+  24) serial_sa1100.c
   -------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  26) serial_sh.c
+  25) serial_sh.c
   ---------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  27) serial_xuartlite.c
+  26) serial_xuartlite.c
   ----------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  28) usbtty.c
+  27) usbtty.c
   ------------
   This driver seems very complicated and entangled with USB framework. The
   conversion might be complicated here.
 
-  29) arch/powerpc/cpu/mpc512x/serial.c
+  28) arch/powerpc/cpu/mpc512x/serial.c
   -------------------------------------
   This driver supports CONFIG_SERIAL_MULTI. This driver will need to be moved to
   proper place.
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index bcb7161..35769c5 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -73,7 +73,6 @@ COBJS-$(CONFIG_NAND_MXS) += mxs_nand.o
 COBJS-$(CONFIG_NAND_NDFC) += ndfc.o
 COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o
 COBJS-$(CONFIG_NAND_S3C2410) += s3c2410_nand.o
-COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o
 COBJS-$(CONFIG_NAND_SPEAR) += spr_nand.o
 COBJS-$(CONFIG_TEGRA_NAND) += tegra_nand.o
 COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
diff --git a/drivers/mtd/nand/s3c64xx.c b/drivers/mtd/nand/s3c64xx.c
deleted file mode 100644
index 87f0341..0000000
--- a/drivers/mtd/nand/s3c64xx.c
+++ /dev/null
@@ -1,295 +0,0 @@
-/*
- * (C) Copyright 2006 DENX Software Engineering
- *
- * Implementation for U-Boot 1.1.6 by Samsung
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#include <nand.h>
-#include <linux/mtd/nand.h>
-
-#include <asm/arch/s3c6400.h>
-
-#include <asm/io.h>
-#include <asm/errno.h>
-
-#define MAX_CHIPS	2
-static int nand_cs[MAX_CHIPS] = {0, 1};
-
-#ifdef CONFIG_NAND_SPL
-#define printf(arg...) do {} while (0)
-#endif
-
-/* Nand flash definition values by jsgood */
-#ifdef S3C_NAND_DEBUG
-/*
- * Function to print out oob buffer for debugging
- * Written by jsgood
- */
-static void print_oob(const char *header, struct mtd_info *mtd)
-{
-	int i;
-	struct nand_chip *chip = mtd->priv;
-
-	printf("%s:\t", header);
-
-	for (i = 0; i < 64; i++)
-		printf("%02x ", chip->oob_poi[i]);
-
-	printf("\n");
-}
-#endif /* S3C_NAND_DEBUG */
-
-static void s3c_nand_select_chip(struct mtd_info *mtd, int chip)
-{
-	int ctrl = readl(NFCONT);
-
-	switch (chip) {
-	case -1:
-		ctrl |= 6;
-		break;
-	case 0:
-		ctrl &= ~2;
-		break;
-	case 1:
-		ctrl &= ~4;
-		break;
-	default:
-		return;
-	}
-
-	writel(ctrl, NFCONT);
-}
-
-/*
- * Hardware specific access to control-lines function
- * Written by jsgood
- */
-static void s3c_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
-	struct nand_chip *this = mtd->priv;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		if (ctrl & NAND_CLE)
-			this->IO_ADDR_W = (void __iomem *)NFCMMD;
-		else if (ctrl & NAND_ALE)
-			this->IO_ADDR_W = (void __iomem *)NFADDR;
-		else
-			this->IO_ADDR_W = (void __iomem *)NFDATA;
-		if (ctrl & NAND_NCE)
-			s3c_nand_select_chip(mtd, *(int *)this->priv);
-		else
-			s3c_nand_select_chip(mtd, -1);
-	}
-
-	if (cmd != NAND_CMD_NONE)
-		writeb(cmd, this->IO_ADDR_W);
-}
-
-/*
- * Function for checking device ready pin
- * Written by jsgood
- */
-static int s3c_nand_device_ready(struct mtd_info *mtdinfo)
-{
-	return !!(readl(NFSTAT) & NFSTAT_RnB);
-}
-
-#ifdef CONFIG_SYS_S3C_NAND_HWECC
-/*
- * This function is called before encoding ecc codes to ready ecc engine.
- * Written by jsgood
- */
-static void s3c_nand_enable_hwecc(struct mtd_info *mtd, int mode)
-{
-	u_long nfcont, nfconf;
-
-	/*
-	 * The original driver used 4-bit ECC for "new" MLC chips, i.e., for
-	 * those with non-zero ID[3][3:2], which anyway only holds for ST
-	 * (Numonyx) chips
-	 */
-	nfconf = readl(NFCONF) & ~NFCONF_ECC_4BIT;
-
-	writel(nfconf, NFCONF);
-
-	/* Initialize & unlock */
-	nfcont = readl(NFCONT);
-	nfcont |= NFCONT_INITECC;
-	nfcont &= ~NFCONT_MECCLOCK;
-
-	if (mode == NAND_ECC_WRITE)
-		nfcont |= NFCONT_ECC_ENC;
-	else if (mode == NAND_ECC_READ)
-		nfcont &= ~NFCONT_ECC_ENC;
-
-	writel(nfcont, NFCONT);
-}
-
-/*
- * This function is called immediately after encoding ecc codes.
- * This function returns encoded ecc codes.
- * Written by jsgood
- */
-static int s3c_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
-				  u_char *ecc_code)
-{
-	u_long nfcont, nfmecc0;
-
-	/* Lock */
-	nfcont = readl(NFCONT);
-	nfcont |= NFCONT_MECCLOCK;
-	writel(nfcont, NFCONT);
-
-	nfmecc0 = readl(NFMECC0);
-
-	ecc_code[0] = nfmecc0 & 0xff;
-	ecc_code[1] = (nfmecc0 >> 8) & 0xff;
-	ecc_code[2] = (nfmecc0 >> 16) & 0xff;
-	ecc_code[3] = (nfmecc0 >> 24) & 0xff;
-
-	return 0;
-}
-
-/*
- * This function determines whether read data is good or not.
- * If SLC, must write ecc codes to controller before reading status bit.
- * If MLC, status bit is already set, so only reading is needed.
- * If status bit is good, return 0.
- * If correctable errors occured, do that.
- * If uncorrectable errors occured, return -1.
- * Written by jsgood
- */
-static int s3c_nand_correct_data(struct mtd_info *mtd, u_char *dat,
-				 u_char *read_ecc, u_char *calc_ecc)
-{
-	int ret = -1;
-	u_long nfestat0, nfmeccdata0, nfmeccdata1, err_byte_addr;
-	u_char err_type, repaired;
-
-	/* SLC: Write ecc to compare */
-	nfmeccdata0 = (calc_ecc[1] << 16) | calc_ecc[0];
-	nfmeccdata1 = (calc_ecc[3] << 16) | calc_ecc[2];
-	writel(nfmeccdata0, NFMECCDATA0);
-	writel(nfmeccdata1, NFMECCDATA1);
-
-	/* Read ecc status */
-	nfestat0 = readl(NFESTAT0);
-	err_type = nfestat0 & 0x3;
-
-	switch (err_type) {
-	case 0: /* No error */
-		ret = 0;
-		break;
-
-	case 1:
-		/*
-		 * 1 bit error (Correctable)
-		 * (nfestat0 >> 7) & 0x7ff	:error byte number
-		 * (nfestat0 >> 4) & 0x7	:error bit number
-		 */
-		err_byte_addr = (nfestat0 >> 7) & 0x7ff;
-		repaired = dat[err_byte_addr] ^ (1 << ((nfestat0 >> 4) & 0x7));
-
-		printf("S3C NAND: 1 bit error detected at byte %ld. "
-		       "Correcting from 0x%02x to 0x%02x...OK\n",
-		       err_byte_addr, dat[err_byte_addr], repaired);
-
-		dat[err_byte_addr] = repaired;
-
-		ret = 1;
-		break;
-
-	case 2: /* Multiple error */
-	case 3: /* ECC area error */
-		printf("S3C NAND: ECC uncorrectable error detected. "
-		       "Not correctable.\n");
-		ret = -1;
-		break;
-	}
-
-	return ret;
-}
-#endif /* CONFIG_SYS_S3C_NAND_HWECC */
-
-/*
- * Board-specific NAND initialization. The following members of the
- * argument are board-specific (per include/linux/mtd/nand.h):
- * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device
- * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device
- * - hwcontrol: hardwarespecific function for accesing control-lines
- * - dev_ready: hardwarespecific function for  accesing device ready/busy line
- * - enable_hwecc?: function to enable (reset)  hardware ecc generator. Must
- *   only be provided if a hardware ECC is available
- * - eccmode: mode of ecc, see defines
- * - chip_delay: chip dependent delay for transfering data from array to
- *   read regs (tR)
- * - options: various chip options. They can partly be set to inform
- *   nand_scan about special functionality. See the defines for further
- *   explanation
- * Members with a "?" were not set in the merged testing-NAND branch,
- * so they are not set here either.
- */
-int board_nand_init(struct nand_chip *nand)
-{
-	static int chip_n;
-
-	if (chip_n >= MAX_CHIPS)
-		return -ENODEV;
-
-	NFCONT_REG = (NFCONT_REG & ~NFCONT_WP) | NFCONT_ENABLE | 0x6;
-
-	nand->IO_ADDR_R		= (void __iomem *)NFDATA;
-	nand->IO_ADDR_W		= (void __iomem *)NFDATA;
-	nand->cmd_ctrl		= s3c_nand_hwcontrol;
-	nand->dev_ready		= s3c_nand_device_ready;
-	nand->select_chip	= s3c_nand_select_chip;
-	nand->options		= 0;
-#ifdef CONFIG_NAND_SPL
-	nand->read_byte		= nand_read_byte;
-	nand->write_buf		= nand_write_buf;
-	nand->read_buf		= nand_read_buf;
-#endif
-
-#ifdef CONFIG_SYS_S3C_NAND_HWECC
-	nand->ecc.hwctl		= s3c_nand_enable_hwecc;
-	nand->ecc.calculate	= s3c_nand_calculate_ecc;
-	nand->ecc.correct	= s3c_nand_correct_data;
-
-	/*
-	 * If you get more than 1 NAND-chip with different page-sizes on the
-	 * board one day, it will get more complicated...
-	 */
-	nand->ecc.mode		= NAND_ECC_HW;
-	nand->ecc.size		= CONFIG_SYS_NAND_ECCSIZE;
-	nand->ecc.bytes		= CONFIG_SYS_NAND_ECCBYTES;
-#else
-	nand->ecc.mode		= NAND_ECC_SOFT;
-#endif /* ! CONFIG_SYS_S3C_NAND_HWECC */
-
-	nand->priv		= nand_cs + chip_n++;
-
-	return 0;
-}
diff --git a/drivers/mtd/onenand/onenand_base.c b/drivers/mtd/onenand/onenand_base.c
index 1a7b40e..858e322 100644
--- a/drivers/mtd/onenand/onenand_base.c
+++ b/drivers/mtd/onenand/onenand_base.c
@@ -632,10 +632,6 @@ static int onenand_check_bufferram(struct mtd_info *mtd, loff_t addr)
 	int blockpage, found = 0;
 	unsigned int i;
 
-#ifdef CONFIG_S3C64XX
-	return 0;
-#endif
-
 	if (ONENAND_IS_2PLANE(this))
 		blockpage = onenand_get_2x_blockpage(mtd, addr);
 	else
diff --git a/drivers/mtd/onenand/samsung.c b/drivers/mtd/onenand/samsung.c
index 0d94ea5..5eb2b3a 100644
--- a/drivers/mtd/onenand/samsung.c
+++ b/drivers/mtd/onenand/samsung.c
@@ -1,5 +1,5 @@
 /*
- * S3C64XX/S5PC100 OneNAND driver at U-Boot
+ * S5PC100 OneNAND driver at U-Boot
  *
  * Copyright (C) 2008-2009 Samsung Electronics
  * Kyungmin Park <kyungmin.park at samsung.com>
@@ -62,12 +62,7 @@ do {									\
 #define ONENAND_MAIN_SPARE_ACCESS	0x16
 #define ONENAND_PIPELINE_READ		0x4000
 
-#if defined(CONFIG_S3C64XX)
-#define MAP_00				(0x0 << 24)
-#define MAP_01				(0x1 << 24)
-#define MAP_10				(0x2 << 24)
-#define MAP_11				(0x3 << 24)
-#elif defined(CONFIG_S5P)
+#if defined(CONFIG_S5P)
 #define MAP_00				(0x0 << 26)
 #define MAP_01				(0x1 << 26)
 #define MAP_10				(0x2 << 26)
@@ -116,12 +111,7 @@ static void s3c_write_cmd(int value, unsigned int cmd)
  * return the buffer address on the memory device
  * It will be combined with CMD_MAP_XX
  */
-#if defined(CONFIG_S3C64XX)
-static unsigned int s3c_mem_addr(int fba, int fpa, int fsa)
-{
-	return (fba << 12) | (fpa << 6) | (fsa << 4);
-}
-#elif defined(CONFIG_S5P)
+#if defined(CONFIG_S5P)
 static unsigned int s3c_mem_addr(int fba, int fpa, int fsa)
 {
 	return (fba << 13) | (fpa << 7) | (fsa << 5);
@@ -550,45 +540,6 @@ static void s3c_onenand_unlock_all(struct mtd_info *mtd)
 	s3c_onenand_check_lock_status(mtd);
 }
 
-#ifdef CONFIG_S3C64XX
-static void s3c_set_width_regs(struct onenand_chip *this)
-{
-	int dev_id, density;
-	int fba, fpa, fsa;
-	int dbs_dfs;
-
-	dev_id = DEVICE_ID0_REG;
-
-	density = (dev_id >> ONENAND_DEVICE_DENSITY_SHIFT) & 0xf;
-	dbs_dfs = !!(dev_id & ONENAND_DEVICE_IS_DDP);
-
-	fba = density + 7;
-	if (dbs_dfs)
-		fba--;		/* Decrease the fba */
-	fpa = 6;
-	if (density >= ONENAND_DEVICE_DENSITY_512Mb)
-		fsa = 2;
-	else
-		fsa = 1;
-
-	DPRINTK("FBA %lu, FPA %lu, FSA %lu, DDP %lu",
-		FBA_WIDTH0_REG, FPA_WIDTH0_REG, FSA_WIDTH0_REG,
-		DDP_DEVICE_REG);
-
-	DPRINTK("mem_cfg0 0x%lx, sync mode %lu, "
-		"dev_page_size %lu, BURST LEN %lu",
-		MEM_CFG0_REG, SYNC_MODE_REG,
-		DEV_PAGE_SIZE_REG, BURST_LEN0_REG);
-
-	DEV_PAGE_SIZE_REG = 0x1;
-
-	FBA_WIDTH0_REG = fba;
-	FPA_WIDTH0_REG = fpa;
-	FSA_WIDTH0_REG = fsa;
-	DBS_DFS_WIDTH0_REG = dbs_dfs;
-}
-#endif
-
 int s5pc110_chip_probe(struct mtd_info *mtd)
 {
 	return 0;
@@ -620,10 +571,7 @@ void s3c_onenand_init(struct mtd_info *mtd)
 
 	onenand->mtd = mtd;
 
-#if defined(CONFIG_S3C64XX)
-	onenand->base = (void *)0x70100000;
-	onenand->ahb_addr = (void *)0x20000000;
-#elif defined(CONFIG_S5P)
+#if defined(CONFIG_S5P)
 	onenand->base = (void *)0xE7100000;
 	onenand->ahb_addr = (void *)0xB0000000;
 #endif
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index de3f471..fbc4e97 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -35,7 +35,6 @@ COBJS-$(CONFIG_LPC32XX_HSUART) += lpc32xx_hsuart.o
 COBJS-$(CONFIG_MCFUART) += mcfuart.o
 COBJS-$(CONFIG_OPENCORES_YANU) += opencores_yanu.o
 COBJS-$(CONFIG_SYS_NS16550) += ns16550.o
-COBJS-$(CONFIG_S3C64XX) += s3c64xx.o
 COBJS-$(CONFIG_S5P) += serial_s5p.o
 COBJS-$(CONFIG_SYS_NS16550_SERIAL) += serial_ns16550.o
 COBJS-$(CONFIG_IMX_SERIAL) += serial_imx.o
diff --git a/drivers/serial/s3c64xx.c b/drivers/serial/s3c64xx.c
deleted file mode 100644
index b590992..0000000
--- a/drivers/serial/s3c64xx.c
+++ /dev/null
@@ -1,187 +0,0 @@
-/*
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj at denx.de>
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#include <common.h>
-#include <linux/compiler.h>
-#include <serial.h>
-#include <asm/arch/s3c6400.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_SERIAL1
-#define UART_NR	S3C64XX_UART0
-
-#elif defined(CONFIG_SERIAL2)
-#define UART_NR	S3C64XX_UART1
-
-#elif defined(CONFIG_SERIAL3)
-#define UART_NR	S3C64XX_UART2
-
-#else
-#error "Bad: you didn't configure serial ..."
-#endif
-
-/*
- * The coefficient, used to calculate the baudrate on S3C6400 UARTs is
- * calculated as
- * C = UBRDIV * 16 + number_of_set_bits_in_UDIVSLOT
- * however, section 31.6.11 of the datasheet doesn't recomment using 1 for 1,
- * 3 for 2, ... (2^n - 1) for n, instead, they suggest using these constants:
- */
-static const int udivslot[] = {
-	0,
-	0x0080,
-	0x0808,
-	0x0888,
-	0x2222,
-	0x4924,
-	0x4a52,
-	0x54aa,
-	0x5555,
-	0xd555,
-	0xd5d5,
-	0xddd5,
-	0xdddd,
-	0xdfdd,
-	0xdfdf,
-	0xffdf,
-};
-
-static void s3c64xx_serial_setbrg(void)
-{
-	s3c64xx_uart *const uart = s3c64xx_get_base_uart(UART_NR);
-	u32 pclk = get_PCLK();
-	u32 baudrate = gd->baudrate;
-	int i;
-
-	i = (pclk / baudrate) % 16;
-
-	uart->UBRDIV = pclk / baudrate / 16 - 1;
-	uart->UDIVSLOT = udivslot[i];
-
-	for (i = 0; i < 100; i++)
-		barrier();
-}
-
-/*
- * Initialise the serial port with the given baudrate. The settings
- * are always 8 data bits, no parity, 1 stop bit, no start bits.
- */
-static int s3c64xx_serial_init(void)
-{
-	s3c64xx_uart *const uart = s3c64xx_get_base_uart(UART_NR);
-
-	/* reset and enable FIFOs, set triggers to the maximum */
-	uart->UFCON = 0xff;
-	uart->UMCON = 0;
-	/* 8N1 */
-	uart->ULCON = 3;
-	/* No interrupts, no DMA, pure polling */
-	uart->UCON = 5;
-
-	serial_setbrg();
-
-	return 0;
-}
-
-/*
- * Read a single byte from the serial port. Returns 1 on success, 0
- * otherwise. When the function is succesfull, the character read is
- * written into its argument c.
- */
-static int s3c64xx_serial_getc(void)
-{
-	s3c64xx_uart *const uart = s3c64xx_get_base_uart(UART_NR);
-
-	/* wait for character to arrive */
-	while (!(uart->UTRSTAT & 0x1));
-
-	return uart->URXH & 0xff;
-}
-
-#ifdef CONFIG_MODEM_SUPPORT
-static int be_quiet;
-void disable_putc(void)
-{
-	be_quiet = 1;
-}
-
-void enable_putc(void)
-{
-	be_quiet = 0;
-}
-#endif
-
-
-/*
- * Output a single byte to the serial port.
- */
-static void s3c64xx_serial_putc(const char c)
-{
-	s3c64xx_uart *const uart = s3c64xx_get_base_uart(UART_NR);
-
-#ifdef CONFIG_MODEM_SUPPORT
-	if (be_quiet)
-		return;
-#endif
-
-	/* wait for room in the tx FIFO */
-	while (!(uart->UTRSTAT & 0x2));
-
-	uart->UTXH = c;
-
-	/* If \n, also do \r */
-	if (c == '\n')
-		serial_putc('\r');
-}
-
-/*
- * Test whether a character is in the RX buffer
- */
-static int s3c64xx_serial_tstc(void)
-{
-	s3c64xx_uart *const uart = s3c64xx_get_base_uart(UART_NR);
-
-	return uart->UTRSTAT & 0x1;
-}
-
-static struct serial_device s3c64xx_serial_drv = {
-	.name	= "s3c64xx_serial",
-	.start	= s3c64xx_serial_init,
-	.stop	= NULL,
-	.setbrg	= s3c64xx_serial_setbrg,
-	.putc	= s3c64xx_serial_putc,
-	.puts	= default_serial_puts,
-	.getc	= s3c64xx_serial_getc,
-	.tstc	= s3c64xx_serial_tstc,
-};
-
-void s3c64xx_serial_initialize(void)
-{
-	serial_register(&s3c64xx_serial_drv);
-}
-
-__weak struct serial_device *default_serial_console(void)
-{
-	return &s3c64xx_serial_drv;
-}
diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index 7922bf0..9f04643 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -165,7 +165,6 @@ serial_initfunc(atmel_serial_initialize);
 serial_initfunc(lpc32xx_serial_initialize);
 serial_initfunc(mcf_serial_initialize);
 serial_initfunc(oc_serial_initialize);
-serial_initfunc(s3c64xx_serial_initialize);
 serial_initfunc(sandbox_serial_initialize);
 serial_initfunc(clps7111_serial_initialize);
 serial_initfunc(imx_serial_initialize);
@@ -259,7 +258,6 @@ void serial_initialize(void)
 	lpc32xx_serial_initialize();
 	mcf_serial_initialize();
 	oc_serial_initialize();
-	s3c64xx_serial_initialize();
 	sandbox_serial_initialize();
 	clps7111_serial_initialize();
 	imx_serial_initialize();
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 9a6f982..87a5970 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -31,7 +31,6 @@ COBJS-$(CONFIG_USB_ATMEL) += ohci-at91.o
 COBJS-$(CONFIG_USB_OHCI_DA8XX) += ohci-da8xx.o
 COBJS-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
 COBJS-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o
-COBJS-$(CONFIG_USB_S3C64XX) += s3c64xx-hcd.o
 COBJS-$(CONFIG_USB_SL811HS) += sl811-hcd.o
 COBJS-$(CONFIG_USB_OHCI_S3C24XX) += ohci-s3c24xx.o
 
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index bdbe250..bc17b85 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -66,7 +66,6 @@
 
 #if defined(CONFIG_ARM920T) || \
     defined(CONFIG_S3C24X0) || \
-    defined(CONFIG_S3C6400) || \
     defined(CONFIG_440EP) || \
     defined(CONFIG_PCI_OHCI) || \
     defined(CONFIG_MPC5200) || \
diff --git a/drivers/usb/host/s3c64xx-hcd.c b/drivers/usb/host/s3c64xx-hcd.c
deleted file mode 100644
index cd295da..0000000
--- a/drivers/usb/host/s3c64xx-hcd.c
+++ /dev/null
@@ -1,45 +0,0 @@
-/*
- * URB OHCI HCD (Host Controller Driver) initialization for USB on the S3C64XX.
- *
- * Copyright (C) 2008,
- * Guennadi Liakhovetski, DENX Software Engineering <lg at denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- */
-
-#include <common.h>
-#include <asm/arch/s3c6400.h>
-
-int usb_cpu_init(void)
-{
-	OTHERS_REG |= 0x10000;
-	return 0;
-}
-
-int usb_cpu_stop(void)
-{
-	OTHERS_REG &= ~0x10000;
-	return 0;
-}
-
-void usb_cpu_init_fail(void)
-{
-	OTHERS_REG &= ~0x10000;
-}
diff --git a/include/common.h b/include/common.h
index 604176c..0cfa6a8 100644
--- a/include/common.h
+++ b/include/common.h
@@ -647,7 +647,6 @@ ulong	get_PCI_freq (void);
 #endif
 #if defined(CONFIG_S3C24X0) || \
     defined(CONFIG_LH7A40X) || \
-    defined(CONFIG_S3C6400) || \
     defined(CONFIG_EP93XX)
 ulong	get_FCLK (void);
 ulong	get_HCLK (void);
diff --git a/include/onenand_uboot.h b/include/onenand_uboot.h
index f321d8a..fd01040 100644
--- a/include/onenand_uboot.h
+++ b/include/onenand_uboot.h
@@ -48,10 +48,6 @@ extern int flexonenand_region(struct mtd_info *mtd, loff_t addr);
 extern int flexonenand_set_boundary(struct mtd_info *mtd, int die,
 					int boundary, int lock);
 
-/* S3C64xx */
-extern void s3c64xx_onenand_init(struct mtd_info *);
-extern void s3c64xx_set_width_regs(struct onenand_chip *);
-
 /* SPL */
 void onenand_spl_load_image(uint32_t offs, uint32_t size, void *dst);
 
-- 
1.7.10.4



More information about the U-Boot mailing list