[U-Boot] [PATCH v3 1/1] ARM: Add support for Seagate GoFlexHome
Albert ARIBAUD
albert.u.boot at aribaud.net
Thu Apr 11 08:26:18 CEST 2013
Hi Suriyan,
On Wed, 10 Apr 2013 17:04:33 -0700, Suriyan Ramasami
<suriyan.r at gmail.com> wrote:
> This is yet another attempt with patch v3.
> Thanks to Wolfgang, Prafulla and Albert for comments, corrections,
> and suggestions.
>
> Comments on the files:
> MAINTAINERS:
> Add maintainer entry for the Seagate GoFlexHome
>
> board/Seagate/goflexhome/Makefile:
> Start with the Dockstar Makefile
> The object file is goflexhome.o
>
> board/Seagate/goflexhome/goflexhome.c:
> Start with dockstar.c and rename it to goflexhome.c
> Include goflexhome.h instead of dockstar.h
> Change #define DOCKSTAR_* to #define GOFLEXHOME_*
> Change the MACH_TYPE_DOCKSTAR to MACH_TYPE_GOFLEXHOME to reflect
> that its a GoFlexHome.
>
> board/Seagate/goflexhome/goflexhome.h:
> Start with dockstar.h and rename it to goflexhome.h
> In all the #defines cosmetically change DOCKSTAR to GOFLEXHOME
>
> board/Seagate/goflexhome/kwbimage.cfg:
> Copy the dockstar/kwbimage.cfg to goflexhome/kwbimage.cfg
>
> boards.cfg:
> Copy the dockstar line and rename dockstar to goflexhome
>
> include/configs/goflexhome.h:
> Start with dockstar.h and rename it to goflexhome.h
> Change CONFIG_IDENT_STRING to be GoFlex specific
> Add #define CONFIG_CMD_IDE, CONFIG_MVSATA_IDE for IDE support
> Add #define CONFIG_CMD_DATE, CONFIG_RTC_MV for RTC support
> Add #define CONFIG_CMD_EXT4 for supporting ext4 FS
> Change CONFIG_SYS_PROMPT to be GoFlex specific
> Change CONFIG_ENV_ADDR and CONFIG_ENV_OFFSET to the default address
> present in ArchLinuxArm install (/etc/fw_env.config)
>
> Signed-off-by: Suriyan Ramasami <suriyan.r at gmail.com>
The text above, until the line '---' below, will remain in the commit
message. This message should only be a one-line summary and a few lines
of general description.
Here, the 'thank you' part (appreciated nonetheless!) should be moved
down just below the '---' separator line , and the details on the
changes should simply not be given (after all, it all can be seen in
the diff).
> ---
> Changes in v3:
> Squash the board support in one file
> Remove goflexhomemenu.c from this patch as its not board related
>
> Changes in v2:
> Coding style changes
>
> MAINTAINERS | 4 +
> board/Seagate/goflexhome/Makefile | 51 +++++++++
> board/Seagate/goflexhome/goflexhome.c | 187 +++++++++++++++++++++++++++++++++
> board/Seagate/goflexhome/goflexhome.h | 47 ++++++++
> board/Seagate/goflexhome/kwbimage.cfg | 168 +++++++++++++++++++++++++++++
> boards.cfg | 1 +
> include/configs/goflexhome.h | 135 ++++++++++++++++++++++++
> 7 files changed, 593 insertions(+), 0 deletions(-)
> create mode 100644 board/Seagate/goflexhome/Makefile
> create mode 100644 board/Seagate/goflexhome/goflexhome.c
> create mode 100644 board/Seagate/goflexhome/goflexhome.h
> create mode 100644 board/Seagate/goflexhome/kwbimage.cfg
> create mode 100644 include/configs/goflexhome.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 1614b91..6292a58 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -847,6 +847,10 @@ Sricharan R <r.sricharan at ti.com>
> omap4_sdp4430 ARM ARMV7 (OMAP4xx SoC)
> omap5_evm ARM ARMV7 (OMAP5xx Soc)
>
> +Suriyan Ramasami <suriyan.r at gmail.com>
> +
> + goflexhome ARM926EJS (Kirkwood SoC)
> +
> Thierry Reding <thierry.reding at avionic-design.de>
>
> plutux Tegra20 (ARM7 & A9 Dual Core)
> diff --git a/board/Seagate/goflexhome/Makefile b/board/Seagate/goflexhome/Makefile
> new file mode 100644
> index 0000000..9948fe2
> --- /dev/null
> +++ b/board/Seagate/goflexhome/Makefile
> @@ -0,0 +1,51 @@
> +#
> +# Copyright (C) 2013 Suriyan Ramasami <suriyan.r at gmail.com>
> +#
> +# Based on dockstar/Makefile originally written by
> +# Copyright (C) 2010 Eric C. Cooper <ecc at cmu.edu>
> +#
> +# Based on sheevaplug/Makefile originally written by
> +# Prafulla Wadaskar <prafulla at marvell.com>
> +# (C) Copyright 2009
> +# Marvell Semiconductor <www.marvell.com>
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> +# MA 02110-1301 USA
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB = $(obj)lib$(BOARD).o
> +
> +COBJS := goflexhome.o
> +
> +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS))
> +SOBJS := $(addprefix $(obj),$(SOBJS))
> +
> +$(LIB): $(obj).depend $(OBJS) $(SOBJS)
> + $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/Seagate/goflexhome/goflexhome.c b/board/Seagate/goflexhome/goflexhome.c
> new file mode 100644
> index 0000000..c1314fb
> --- /dev/null
> +++ b/board/Seagate/goflexhome/goflexhome.c
> @@ -0,0 +1,187 @@
> +/*
> + * Copyright (C) 2013 Suriyan Ramasami <suriyan.r at gmail.com>
> + *
> + * Based on dockstar.c originally written by
> + * Copyright (C) 2010 Eric C. Cooper <ecc at cmu.edu>
> + *
> + * Based on sheevaplug.c originally written by
> + * Prafulla Wadaskar <prafulla at marvell.com>
> + * (C) Copyright 2009
> + * Marvell Semiconductor <www.marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +#include <common.h>
> +#include <miiphy.h>
> +#include <asm/arch/kirkwood.h>
> +#include <asm/arch/mpp.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/io.h>
> +#include "goflexhome.h"
> +
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int board_early_init_f(void)
> +{
> + /*
> + * default gpio configuration
> + * There are maximum 64 gpios controlled through 2 sets of registers
> + * the below configuration configures mainly initial LED status
> + */
> + kw_config_gpio(GOFLEXHOME_OE_VAL_LOW,
> + GOFLEXHOME_OE_VAL_HIGH,
> + GOFLEXHOME_OE_LOW, GOFLEXHOME_OE_HIGH);
> +
> + /* Multi-Purpose Pins Functionality configuration */
> + static const u32 kwmpp_config[] = {
> + MPP0_NF_IO2,
> + MPP1_NF_IO3,
> + MPP2_NF_IO4,
> + MPP3_NF_IO5,
> + MPP4_NF_IO6,
> + MPP5_NF_IO7,
> + MPP6_SYSRST_OUTn,
> + MPP7_GPO,
> + MPP8_UART0_RTS,
> + MPP9_UART0_CTS,
> + MPP10_UART0_TXD,
> + MPP11_UART0_RXD,
> + MPP12_SD_CLK,
> + MPP13_SD_CMD,
> + MPP14_SD_D0,
> + MPP15_SD_D1,
> + MPP16_SD_D2,
> + MPP17_SD_D3,
> + MPP18_NF_IO0,
> + MPP19_NF_IO1,
> + MPP20_GPIO,
> + MPP21_GPIO,
> + MPP22_GPIO,
> + MPP23_GPIO,
> + MPP24_GPIO,
> + MPP25_GPIO,
> + MPP26_GPIO,
> + MPP27_GPIO,
> + MPP28_GPIO,
> + MPP29_TSMP9,
> + MPP30_GPIO,
> + MPP31_GPIO,
> + MPP32_GPIO,
> + MPP33_GPIO,
> + MPP34_GPIO,
> + MPP35_GPIO,
> + MPP36_GPIO,
> + MPP37_GPIO,
> + MPP38_GPIO,
> + MPP39_GPIO,
> + MPP40_GPIO,
> + MPP41_GPIO,
> + MPP42_GPIO,
> + MPP43_GPIO,
> + MPP44_GPIO,
> + MPP45_GPIO,
> + MPP46_GPIO,
> + MPP47_GPIO,
> + MPP48_GPIO,
> + MPP49_GPIO,
> + 0
> + };
> + kirkwood_mpp_conf(kwmpp_config, NULL);
> + return 0;
> +}
> +
> +int board_init(void)
> +{
> + /*
> + * arch number of board
> + */
> + gd->bd->bi_arch_number = MACH_TYPE_GOFLEXHOME;
> +
> + /* address of boot parameters */
> + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_RESET_PHY_R
> +/* Configure and enable MV88E1116 PHY */
> +void reset_phy(void)
> +{
> + u16 reg;
> + u16 devadr;
> + char *name = "egiga0";
> +
> + if (miiphy_set_current_dev(name))
> + return;
> +
> + /* command to read PHY dev address */
> + if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) {
> + printf("Err..%s could not read PHY dev address\n",
> + __func__);
> + return;
> + }
> +
> + /*
> + * Enable RGMII delay on Tx and Rx for CPU port
> + * Ref: sec 4.7.2 of chip datasheet
> + */
> + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
> + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
> + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
> + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
> + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
> +
> + /* reset the phy */
> + miiphy_reset(name, devadr);
> +
> + printf("88E1116 Initialized on %s\n", name);
> +}
> +#endif /* CONFIG_RESET_PHY_R */
> +
> +#define GREEN_LED (1 << 14)
> +#define ORANGE_LED (1 << 15)
> +#define BOTH_LEDS (GREEN_LED | ORANGE_LED)
> +#define NEITHER_LED 0
> +
> +static void set_leds(u32 leds, u32 blinking)
> +{
> + struct kwgpio_registers *r = (struct kwgpio_registers *)KW_GPIO1_BASE;
> + u32 oe = readl(&r->oe) | BOTH_LEDS;
> + writel(oe & ~leds, &r->oe); /* active low */
> + u32 bl = readl(&r->blink_en) & ~BOTH_LEDS;
> + writel(bl | blinking, &r->blink_en);
> +}
> +
> +void show_boot_progress(int val)
> +{
> + switch (val) {
> + case BOOTSTAGE_ID_RUN_OS: /* booting Linux */
> + set_leds(BOTH_LEDS, NEITHER_LED);
> + break;
> + case BOOTSTAGE_ID_NET_ETH_START: /* Ethernet initialization */
> + set_leds(GREEN_LED, GREEN_LED);
> + break;
> + default:
> + if (val < 0) /* error */
> + set_leds(ORANGE_LED, ORANGE_LED);
> + break;
> + }
> +}
> diff --git a/board/Seagate/goflexhome/goflexhome.h b/board/Seagate/goflexhome/goflexhome.h
> new file mode 100644
> index 0000000..2af2596
> --- /dev/null
> +++ b/board/Seagate/goflexhome/goflexhome.h
> @@ -0,0 +1,47 @@
> +/*
> + * Copyright (C) 2013 Suriyan Ramasami <suriyan.r at gmail.com>
> + *
> + * Based on dockstar.h originally written by
> + * Copyright (C) 2010 Eric C. Cooper <ecc at cmu.edu>
> + *
> + * Based on sheevaplug.h originally written by
> + * Prafulla Wadaskar <prafulla at marvell.com>
> + * (C) Copyright 2009
> + * Marvell Semiconductor <www.marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +#ifndef __GOFLEXHOME_H
> +#define __GOFLEXHOME_H
> +
> +#define GOFLEXHOME_OE_LOW (~(0))
> +#define GOFLEXHOME_OE_HIGH (~(0))
> +#define GOFLEXHOME_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
> +#define GOFLEXHOME_OE_VAL_HIGH (1 << 17) /* LED pin high */
> +
> +/* PHY related */
> +#define MV88E1116_LED_FCTRL_REG 10
> +#define MV88E1116_CPRSP_CR3_REG 21
> +#define MV88E1116_MAC_CTRL_REG 21
> +#define MV88E1116_PGADR_REG 22
> +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
> +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
> +
> +#endif /* __GOFLEXHOME_H */
> diff --git a/board/Seagate/goflexhome/kwbimage.cfg b/board/Seagate/goflexhome/kwbimage.cfg
> new file mode 100644
> index 0000000..e984d72
> --- /dev/null
> +++ b/board/Seagate/goflexhome/kwbimage.cfg
> @@ -0,0 +1,168 @@
> +#
> +# Copyright (C) 2013 Suriyan Ramasami <suriyan.r at gmail.com>
> +#
> +# Based on dockstar/kwbimage.cfg originally written by
> +# Copyright (C) 2010 Eric C. Cooper <ecc at cmu.edu>
> +#
> +# Based on sheevaplug/kwbimage.cfg originally written by
> +# Prafulla Wadaskar <prafulla at marvell.com>
> +# (C) Copyright 2009
> +# Marvell Semiconductor <www.marvell.com>
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> +# MA 02110-1301 USA
> +#
> +# Refer docs/README.kwimage for more details about how-to configure
> +# and create kirkwood boot image
> +#
> +
> +# Boot Media configurations
> +BOOT_FROM nand
> +NAND_ECC_MODE default
> +NAND_PAGE_SIZE 0x0800
> +
> +# SOC registers configuration using bootrom header extension
> +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> +
> +# Configure RGMII-0 interface pad voltage to 1.8V
> +DATA 0xFFD100e0 0x1b1b1b9b
> +
> +#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> +DATA 0xFFD01400 0x43000c30 # DDR Configuration register
> +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
> +# bit23-14: zero
> +# bit24: 1= enable exit self refresh mode on DDR access
> +# bit25: 1 required
> +# bit29-26: zero
> +# bit31-30: 01
> +
> +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
> +# bit 4: 0=addr/cmd in smame cycle
> +# bit 5: 0=clk is driven during self refresh, we don't care for APX
> +# bit 6: 0=use recommended falling edge of clk for addr/cmd
> +# bit14: 0=input buffer always powered up
> +# bit18: 1=cpu lock transaction enabled
> +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
> +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> +# bit30-28: 3 required
> +# bit31: 0=no additional STARTBURST delay
> +
> +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
> +# bit3-0: TRAS lsbs
> +# bit7-4: TRCD
> +# bit11- 8: TRP
> +# bit15-12: TWR
> +# bit19-16: TWTR
> +# bit20: TRAS msb
> +# bit23-21: 0x0
> +# bit27-24: TRRD
> +# bit31-28: TRTP
> +
> +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
> +# bit6-0: TRFC
> +# bit8-7: TR2R
> +# bit10-9: TR2W
> +# bit12-11: TW2W
> +# bit31-13: zero required
> +
> +DATA 0xFFD01410 0x0000000d # DDR Address Control
> +# bit1-0: 00, Cs0width=x8
> +# bit3-2: 11, Cs0size=1Gb
> +# bit5-4: 00, Cs1width=nonexistent
> +# bit7-6: 00, Cs1size =nonexistent
> +# bit9-8: 00, Cs2width=nonexistent
> +# bit11-10: 00, Cs2size =nonexistent
> +# bit13-12: 00, Cs3width=nonexistent
> +# bit15-14: 00, Cs3size =nonexistent
> +# bit16: 0, Cs0AddrSel
> +# bit17: 0, Cs1AddrSel
> +# bit18: 0, Cs2AddrSel
> +# bit19: 0, Cs3AddrSel
> +# bit31-20: 0 required
> +
> +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
> +# bit0: 0, OpenPage enabled
> +# bit31-1: 0 required
> +
> +DATA 0xFFD01418 0x00000000 # DDR Operation
> +# bit3-0: 0x0, DDR cmd
> +# bit31-4: 0 required
> +
> +DATA 0xFFD0141C 0x00000C52 # DDR Mode
> +# bit2-0: 2, BurstLen=2 required
> +# bit3: 0, BurstType=0 required
> +# bit6-4: 4, CL=5
> +# bit7: 0, TestMode=0 normal
> +# bit8: 0, DLL reset=0 normal
> +# bit11-9: 6, auto-precharge write recovery ????????????
> +# bit12: 0, PD must be zero
> +# bit31-13: 0 required
> +
> +DATA 0xFFD01420 0x00000040 # DDR Extended Mode
> +# bit0: 0, DDR DLL enabled
> +# bit1: 0, DDR drive strenght normal
> +# bit2: 0, DDR ODT control lsd (disabled)
> +# bit5-3: 000, required
> +# bit6: 1, DDR ODT control msb, (disabled)
> +# bit9-7: 000, required
> +# bit10: 0, differential DQS enabled
> +# bit11: 0, required
> +# bit12: 0, DDR output buffer enabled
> +# bit31-13: 0 required
> +
> +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
> +# bit2-0: 111, required
> +# bit3 : 1 , MBUS Burst Chop disabled
> +# bit6-4: 111, required
> +# bit7 : 0
> +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
> +# bit9 : 0 , no half clock cycle addition to dataout
> +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> +# bit15-12: 1111 required
> +# bit31-16: 0 required
> +
> +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
> +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
> +
> +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
> +# bit0: 1, Window enabled
> +# bit1: 0, Write Protect disabled
> +# bit3-2: 00, CS0 hit selected
> +# bit23-4: ones, required
> +# bit31-24: 0x07, Size (i.e. 128MB)
> +
> +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
> +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
> +
> +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> +
> +DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
> +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
> +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
> +# bit3-2: 01, ODT1 active NEVER!
> +# bit31-4: zero, required
> +
> +DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
> +DATA 0xFFD01480 0x00000001 # DDR Initialization Control
> +#bit0=1, enable DDR init upon this register write
> +
> +# End of Header extension
> +DATA 0x0 0x0
> diff --git a/boards.cfg b/boards.cfg
> index 5fc70be..d6f8593 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -184,6 +184,7 @@ rd6281a arm arm926ejs - Marvell
> sheevaplug arm arm926ejs - Marvell kirkwood
> ib62x0 arm arm926ejs ib62x0 raidsonic kirkwood
> dockstar arm arm926ejs - Seagate kirkwood
> +goflexhome arm arm926ejs - Seagate kirkwood
> tk71 arm arm926ejs tk71 karo kirkwood
> devkit3250 arm arm926ejs devkit3250 timll lpc32xx
> jadecpu arm arm926ejs jadecpu syteco mb86r0x
> diff --git a/include/configs/goflexhome.h b/include/configs/goflexhome.h
> new file mode 100644
> index 0000000..16ad12a
> --- /dev/null
> +++ b/include/configs/goflexhome.h
> @@ -0,0 +1,135 @@
> +/*
> + * Copyright (C) 2013 Suriyan Ramasami <suriyan.r at gmail.com>
> + *
> + * Based on dockstar.h originally written by
> + * Copyright (C) 2010 Eric C. Cooper <ecc at cmu.edu>
> + *
> + * Based on sheevaplug.h originally written by
> + * Prafulla Wadaskar <prafulla at marvell.com>
> + * (C) Copyright 2009
> + * Marvell Semiconductor <www.marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +#ifndef _CONFIG_GOFLEXHOME_H
> +#define _CONFIG_GOFLEXHOME_H
> +
> +/*
> + * Version number information
> + */
> +#define CONFIG_IDENT_STRING "\nSeagate GoFlex Home"
> +
> +/*
> + * High Level Configuration Options (easy to change)
> + */
> +#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
> +#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
> +#define CONFIG_KW88F6281 1 /* SOC Name */
> +#define CONFIG_MACH_GOFLEXHOME /* Machine type */
> +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
> +
> +/*
> + * Commands configuration
> + */
> +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
> +#define CONFIG_CONSOLE_MUX
> +#define CONFIG_SYS_CONSOLE_IS_IN_ENV
> +
> +#include <config_cmd_default.h>
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_ENV
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_NAND
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_USB
> +#define CONFIG_CMD_IDE
> +#define CONFIG_CMD_DATE
> +#define CONFIG_CMD_EXT4
> +#define CONFIG_SYS_MVFS /* Picks up Filesystem from mv-common.h */
> +
> +/*
> + * mv-common.h should be defined after CMD configs since it used them
> + * to enable certain macros
> + */
> +#include "mv-common.h"
> +
> +#undef CONFIG_SYS_PROMPT /* previously defined in mv-common.h */
> +#define CONFIG_SYS_PROMPT "GoFlexHome> " /* Command Prompt */
> +
> +/*
> + * Environment variables configurations
> + */
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_ENV_IS_IN_NAND 1
> +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
> +#else
> +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
> +#endif
> +/*
> + * max 4k env size is enough, but in case of nand
> + * it has to be rounded to sector size
> + */
> +#define CONFIG_ENV_SIZE 0x20000 /* 128k */
> +#define CONFIG_ENV_ADDR 0xC0000
> +#define CONFIG_ENV_OFFSET 0xC0000 /* env starts here */
> +
> +/*
> + * Default environment variables
> + */
> +#define CONFIG_BOOTCOMMAND \
> + "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
> + "ubi part root; " \
> + "ubifsmount ubi:root; " \
> + "ubifsload 0x800000 ${kernel}; " \
> + "bootm 0x800000"
> +
> +#define CONFIG_MTDPARTS \
> + "mtdparts=orion_nand:1m(uboot),6M(uImage),-(root)\0"
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "console=console=ttyS0,115200\0" \
> + "mtdids=nand0=orion_nand\0" \
> + "mtdparts="CONFIG_MTDPARTS \
> + "kernel=/boot/uImage\0" \
> + "bootargs_root=ubi.mtd=root root=ubi0:root rootfstype=ubifs ro\0"
> +
> +/*
> + * Ethernet Driver configuration
> + */
> +#ifdef CONFIG_CMD_NET
> +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
> +#define CONFIG_PHY_BASE_ADR 0
> +#endif /* CONFIG_CMD_NET */
> +
> +/*
> + * * SATA Driver configuration
> + * */
> +#ifdef CONFIG_MVSATA_IDE
> +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
> +#endif /*CONFIG_MVSATA_IDE*/
> +
> +/*
> + * * RTC driver configuration
> + * */
> +#ifdef CONFIG_CMD_DATE
> +#define CONFIG_RTC_MV
> +#endif /* CONFIG_CMD_DATE */
> +
> +#endif /* _CONFIG_GOFLEXHOME_H */
Amicalement,
--
Albert.
More information about the U-Boot
mailing list