[U-Boot] [PATCH][v2] powerpc/85xx: Add TWR-P10xx board support

Xie Xiaobo X.Xie at freescale.com
Thu Apr 25 09:51:11 CEST 2013


TWR-P1025 Specification:
-----------------------
Memory subsystem:
   512MB DDR3 (on board DDR)
   64Mbyte 16bit NOR flash
   One microSD Card slot

Ethernet:
   eTSEC1: Connected to Atheros AR8035 GETH PHY
   eTSEC3: Connected to Atheros AR8035 GETH PHY

UART:
   Two UARTs are routed to the FDTI dual USB to RS232 convertor

USB: Two USB2.0 Type A ports

I2C:
   AT24C01B 1K Board EEPROM (8 bit address)

QUICC Engine:
   Connected to DP83849i PHY supply two 10/100M ethernet ports
   QE UART for RS485 or RS232

PCIE:
   One mini-PCIE slot

Signed-off-by: Michael Johnston <michael.johnston at freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie at freescale.com>
---
 arch/powerpc/include/asm/immap_85xx.h |   5 +
 board/freescale/p1_twr/Makefile       |  52 +++
 board/freescale/p1_twr/ddr.c          |  71 ++++
 board/freescale/p1_twr/law.c          |  32 ++
 board/freescale/p1_twr/p1_twr.c       | 311 +++++++++++++++++
 board/freescale/p1_twr/tlb.c          |  92 +++++
 boards.cfg                            |   1 +
 include/configs/p1_twr.h              | 636 ++++++++++++++++++++++++++++++++++
 8 files changed, 1200 insertions(+)
 create mode 100644 board/freescale/p1_twr/Makefile
 create mode 100644 board/freescale/p1_twr/ddr.c
 create mode 100644 board/freescale/p1_twr/law.c
 create mode 100644 board/freescale/p1_twr/p1_twr.c
 create mode 100644 board/freescale/p1_twr/tlb.c
 create mode 100644 include/configs/p1_twr.h

diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index 296b549..b1d92f4 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -2164,6 +2164,11 @@ typedef struct ccsr_gur {
 	u32	porbmsr;	/* POR boot mode status */
 #define MPC85xx_PORBMSR_HA		0x00070000
 #define MPC85xx_PORBMSR_HA_SHIFT	16
+#define MPC85xx_PORBMSR_ROMLOC_SHIFT	24
+#define PORBMSR_ROMLOC_SPI	0x6
+#define PORBMSR_ROMLOC_SDHC	0x7
+#define PORBMSR_ROMLOC_NAND_2K	0x9
+#define PORBMSR_ROMLOC_NOR	0xf
 	u32	porimpscr;	/* POR I/O impedance status & control */
 	u32	pordevsr;	/* POR I/O device status regsiter */
 #if defined(CONFIG_P1017) || defined(CONFIG_P1023)
diff --git a/board/freescale/p1_twr/Makefile b/board/freescale/p1_twr/Makefile
new file mode 100644
index 0000000..fb29b14
--- /dev/null
+++ b/board/freescale/p1_twr/Makefile
@@ -0,0 +1,52 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB    = $(obj)lib$(BOARD).o
+
+COBJS-y        += $(BOARD).o
+COBJS-y        += ddr.o
+COBJS-y        += law.o
+COBJS-y        += tlb.o
+
+SRCS   := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS   := $(addprefix $(obj),$(COBJS-y))
+SOBJS  := $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/p1_twr/ddr.c b/board/freescale/p1_twr/ddr.c
new file mode 100644
index 0000000..ff278ae
--- /dev/null
+++ b/board/freescale/p1_twr/ddr.c
@@ -0,0 +1,71 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/processor.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+
+/* Fixed sdram init -- doesn't use serial presence detect. */
+phys_size_t fixed_sdram(void)
+{
+	sys_info_t sysinfo;
+	char buf[32];
+	size_t ddr_size;
+	fsl_ddr_cfg_regs_t ddr_cfg_regs = {
+		.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+		.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+		.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+#if CONFIG_CHIP_SELECTS_PER_CTRL > 1
+		.cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS,
+		.cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG,
+		.cs[1].config_2 = CONFIG_SYS_DDR_CS1_CONFIG_2,
+#endif
+		.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3,
+		.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0,
+		.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1,
+		.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2,
+		.ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
+		.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
+		.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1,
+		.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2,
+		.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+		.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL,
+		.ddr_data_init = CONFIG_SYS_DDR_DATA_INIT,
+		.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL,
+		.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+		.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+		.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+		.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+		.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
+		.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL,
+		.ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
+		.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+		.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+	};
+
+	get_sys_info(&sysinfo);
+	printf("Configuring DDR for %s MT/s data rate\n",
+			strmhz(buf, sysinfo.freqDDRBus));
+
+	ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+
+	if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+				ddr_size, LAW_TRGT_IF_DDR_1) < 0) {
+		printf("ERROR setting Local Access Windows for DDR\n");
+		return 0;
+	};
+
+	return ddr_size;
+}
diff --git a/board/freescale/p1_twr/law.c b/board/freescale/p1_twr/law.c
new file mode 100644
index 0000000..a7af200
--- /dev/null
+++ b/board/freescale/p1_twr/law.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_SSD_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC)
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/p1_twr/p1_twr.c b/board/freescale/p1_twr/p1_twr.c
new file mode 100644
index 0000000..3041187
--- /dev/null
+++ b/board/freescale/p1_twr/p1_twr.c
@@ -0,0 +1,311 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <hwconfig.h>
+#include <pci.h>
+#include <i2c.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_lbc.h>
+#include <asm/mp.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <ioports.h>
+#include <asm/fsl_serdes.h>
+#include <netdev.h>
+
+#define SYSCLK_64	64000000
+#define SYSCLK_66	66666666
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	par_io_t *par_io = (par_io_t *) &(gur->qe_par_io);
+	unsigned int cpdat_val = 0;
+
+	/* Set-up up pin muxing based on board switch settings */
+	cpdat_val = par_io[1].cpdat;
+
+	/* Check switch setting for SYSCLK select (PB3)  */
+	if (cpdat_val & 0x10000000)
+		return SYSCLK_64;
+	else
+		return SYSCLK_66;
+
+	return 0;
+}
+
+#ifdef CONFIG_QE
+
+#define PCA_IOPORT_I2C_ADDR		0x23
+#define PCA_IOPORT_OUTPUT_CMD		0x2
+#define PCA_IOPORT_CFG_CMD		0x6
+
+const qe_iop_conf_t qe_iop_conf_tab[] = {
+
+#ifdef CONFIG_TWR_P1025
+	/* GPIO */
+	{1,  0, 1, 0, 0},
+	{1,  18, 1, 0, 0},
+
+	/* GPIO for switch options */
+	{1,  2, 2, 0, 0}, /* PROFIBUS_MODE_SEL */
+	{1,  3, 2, 0, 0}, /* SYS_CLK_SELECT */
+	{1,  29, 2, 0, 0}, /* LOCALBUS_QE_MUXSEL */
+	{1,  30, 2, 0, 0}, /* ETH_TDM_SEL */
+
+	/* QE_MUX_MDC */
+	{1,  19, 1, 0, 1}, /* QE_MUX_MDC */
+
+	/* QE_MUX_MDIO */
+	{1,  20, 3, 0, 1}, /* QE_MUX_MDIO */
+
+	/* UCC_1_MII */
+	{0, 23, 2, 0, 2}, /* CLK12 */
+	{0, 24, 2, 0, 1}, /* CLK9 */
+	{0,  7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0 */
+	{0,  9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1 */
+	{0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2 */
+	{0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */
+	{0,  6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0 */
+	{0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1 */
+	{0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */
+	{0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */
+	{0,  5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */
+	{0, 13, 1, 0, 2}, /* ENET1_TX_ER */
+	{0,  4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B */
+	{0,  8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B */
+	{0, 17, 2, 0, 2}, /* ENET1_CRS */
+	{0, 16, 2, 0, 2}, /* ENET1_COL */
+
+	/* UCC_3_UART */
+	{1, 0, 2, 0, 2}, /* SER3_CD_B */
+	{0, 28, 2, 0, 2}, /* SER3_CTS_B */
+	{0, 29, 1, 0, 2}, /* SER3_RTS_B */
+	{0, 30, 2, 0, 2}, /* SER3_RXD0 */
+	{0, 31, 1, 0, 2}, /* SER3_TXD0 */
+
+	/* UCC_5_RMII */
+	{1, 11, 2, 0, 1}, /* CLK13 */
+	{1, 7,  1, 0, 2}, /* ENET5_TXD0_SER5_TXD0 */
+	{1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1 */
+	{1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0 */
+	{1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1 */
+	{1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B */
+	{1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B */
+	{1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B */
+
+	/* UCC_7_UART */
+	{0, 22, 2, 0, 2}, /* SER7_CD_B */
+	{0, 18, 2, 0, 2}, /* SER7_CTS_B */
+	{0, 19, 1, 0, 2}, /* SER7_RTS_B */
+	{0, 20, 2, 0, 2}, /* SER7_RXD0 */
+	{0, 21, 1, 0, 2}, /* SER7_TXD0 */
+
+	/* TDMA - clock option is configured in OS based on board setting */
+	{1, 23, 2, 0, 2}, /* TDMA_TXD */
+	{1, 25, 2, 0, 2}, /* TDMA_RXD */
+	{1, 26, 1, 0, 2}, /* TDMA_SYNC */
+#endif
+
+	{0,  0, 0, 0, QE_IOP_TAB_END} /* END of table */
+};
+#endif
+
+int board_early_init_f(void)
+{
+	ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+	setbits_be32(&gur->pmuxcr,
+			(MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP));
+
+	/* SDHC_DAT[4:7] not exposed to pins (use as SPI) */
+	clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u8 boot_status;
+
+	printf("Board: %s\n", CONFIG_BOARDNAME);
+
+	boot_status = ((gur->porbmsr) >> MPC85xx_PORBMSR_ROMLOC_SHIFT) & 0xf;
+	puts("rom_loc: ");
+	if (boot_status == PORBMSR_ROMLOC_NOR)
+		puts("nor flash");
+	else if (boot_status == PORBMSR_ROMLOC_SDHC)
+		puts("sd");
+	else
+		puts("unknown");
+	puts("\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+#endif
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */
+		MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,           /* perms, wimge */
+		0, flash_esel, BOOKE_PAGESZ_64M, 1);/* ts, esel, tsize, iprot */
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct fsl_pq_mdio_info mdio_info;
+	struct tsec_info_struct tsec_info[4];
+	ccsr_gur_t *gur __attribute__((unused)) =
+		(void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	int num = 0;
+
+#ifdef CONFIG_TSEC1
+	SET_STD_TSEC_INFO(tsec_info[num], 1);
+	num++;
+#endif
+#ifdef CONFIG_TSEC2
+	SET_STD_TSEC_INFO(tsec_info[num], 2);
+	if (is_serdes_configured(SGMII_TSEC2)) {
+		printf("eTSEC2 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+#ifdef CONFIG_TSEC3
+	SET_STD_TSEC_INFO(tsec_info[num], 3);
+	num++;
+#endif
+
+	if (!num) {
+		printf("No TSECs initialized\n");
+		return 0;
+	}
+
+	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+	mdio_info.name = DEFAULT_MII_NAME;
+
+	fsl_pq_mdio_init(bis, &mdio_info);
+
+	tsec_eth_init(bis, tsec_info, num);
+
+#if defined(CONFIG_UEC_ETH)
+	/* QE0 and QE3 need to be exposed for UCC1
+	 * and UCC5 Eth mode (in PMUXCR register).
+	 * Currently QE/LBC muxed pins assumed to be
+	 * LBC for U-Boot and PMUXCR updated by OS if required */
+
+	uec_standard_init(bis);
+#endif
+
+	return pci_eth_init(bis);
+}
+
+#if defined(CONFIG_QE)
+static void fdt_board_fixup_qe_pins(void *blob)
+{
+	int node;
+
+	if (!hwconfig("qe")) {
+		/* For QE and eLBC pins multiplexing,
+		 * When don't use QE function, remove
+		 * qe node from dt blob.
+		 */
+		node = fdt_path_offset(blob, "/qe");
+		if (node >= 0)
+			fdt_del_node(blob, node);
+	} else {
+		/* For TWR Peripheral Modules - TWR-SER2
+		 * board only can support Signal Port MII,
+		 * so delete one UEC node when use MII port.
+		 */
+		if (hwconfig("mii"))
+			node = fdt_path_offset(blob, "/qe/ucc at 2400");
+		else
+			node = fdt_path_offset(blob, "/qe/ucc at 2000");
+		if (node >= 0)
+			fdt_del_node(blob, node);
+	}
+
+	return;
+}
+#endif
+
+#ifdef CONFIG_OF_BOARD_SETUP
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+	FT_FSL_PCI_SETUP;
+
+#ifdef CONFIG_QE
+	do_fixup_by_compat(blob, "fsl,qe", "status", "okay",
+			sizeof("okay"), 0);
+#endif
+#if defined(CONFIG_TWR_P1025)
+	fdt_board_fixup_qe_pins(blob);
+#endif
+	fdt_fixup_dr_usb(blob, bd);
+}
+#endif
diff --git a/board/freescale/p1_twr/tlb.c b/board/freescale/p1_twr/tlb.c
new file mode 100644
index 0000000..68e109c
--- /dev/null
+++ b/board/freescale/p1_twr/tlb.c
@@ -0,0 +1,92 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
+			0, 0, BOOKE_PAGESZ_4K, 1),
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 1, BOOKE_PAGESZ_1M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+	/* W**G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+			MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+			0, 2, BOOKE_PAGESZ_64M, 1),
+
+	/* W**G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_SSD_BASE, CONFIG_SYS_SSD_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 5, BOOKE_PAGESZ_1M, 1),
+
+#ifdef CONFIG_PCI
+	/* *I*G* - PCI memory 1.5G */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI I/O effective: 192K  */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 4, BOOKE_PAGESZ_256K, 1),
+#endif
+
+#endif
+
+#ifdef CONFIG_SYS_RAMBOOT
+	/* *I*G - eSDHC boot */
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 8, BOOKE_PAGESZ_1G, 1),
+#endif
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index 35f38f3..5bad23a 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -798,6 +798,7 @@ P1025RDB_36BIT               powerpc     mpc85xx     p1_p2_rdb_pc        freesca
 P1025RDB_NAND                powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1025RDB,NAND
 P1025RDB_SDCARD              powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1025RDB,SDCARD
 P1025RDB_SPIFLASH            powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1025RDB,SPIFLASH
+TWR-P1025                    powerpc     mpc85xx     p1_twr              freescale      -           p1_twr:TWR_P1025
 P2010RDB                     powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB
 P2010RDB_36BIT               powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB,36BIT
 P2010RDB_36BIT_SDCARD        powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB,36BIT,SDCARD
diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
new file mode 100644
index 0000000..d18c8f4
--- /dev/null
+++ b/include/configs/p1_twr.h
@@ -0,0 +1,636 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * QorIQ P1 Tower boards configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#if defined(CONFIG_TWR_P1025)
+#define CONFIG_BOARDNAME "TWR-P1025"
+#define CONFIG_P1025
+#define CONFIG_PHY_ATHEROS
+#define CONFIG_QE
+#define CONFIG_SYS_LBC_LBCR	0x00080000	/* Conversion of LBC addr */
+#define CONFIG_SYS_LBC_LCRR	0x80000002	/* LB clock ratio reg */
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RAMBOOT_SDCARD
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE		0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500
+#define CONFIG_MPC85xx
+
+#define CONFIG_MP
+
+#define CONFIG_FSL_ELBC
+#define CONFIG_PCI
+#define CONFIG_PCIE1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2	/* PCIE controler 2 (slot 2) */
+#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW
+#define CONFIG_TSEC_ENET	/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_CMD_SATA
+#define CONFIG_SATA_SIL3114
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /*sysclk for TWR-P1025 */
+
+#define CONFIG_DDR_CLK_FREQ	66666666
+
+#define CONFIG_HWCONFIG
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE
+#define CONFIG_BTB
+
+#define CONFIG_BOARD_EARLY_INIT_F	/* Call board_pre_init */
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x1fffffff
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+#define CONFIG_SYS_CCSRBAR		0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+
+#define CONFIG_SYS_SDRAM_SIZE_LAW	LAW_SIZE_512M
+#define CONFIG_CHIP_SELECTS_PER_CTRL	1
+
+#define CONFIG_SYS_SDRAM_SIZE		(1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+
+/* Default settings for DDR3 */
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000001f
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014202
+#define CONFIG_SYS_DDR_CS0_CONFIG_2	0x00000000
+#define CONFIG_SYS_DDR_CS1_BNDS		0x00000000
+#define CONFIG_SYS_DDR_CS1_CONFIG	0x00000000
+#define CONFIG_SYS_DDR_CS1_CONFIG_2	0x00000000
+
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_INIT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_INIT_EXT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_MODE_CONTROL	0x00000000
+
+#define CONFIG_SYS_DDR_ZQ_CONTROL	0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CONTROL	0x8655a608
+#define CONFIG_SYS_DDR_SR_CNTR		0x00000000
+#define CONFIG_SYS_DDR_RCW_1		0x00000000
+#define CONFIG_SYS_DDR_RCW_2		0x00000000
+#define CONFIG_SYS_DDR_CONTROL		0xc70c0000	/* Type = DDR3	*/
+#define CONFIG_SYS_DDR_CONTROL_2	0x04401050
+#define CONFIG_SYS_DDR_TIMING_4		0x00220001
+#define CONFIG_SYS_DDR_TIMING_5		0x03402400
+
+#define CONFIG_SYS_DDR_TIMING_3		0x00020000
+#define CONFIG_SYS_DDR_TIMING_0		0x00220004
+#define CONFIG_SYS_DDR_TIMING_1		0x5c5b6544
+#define CONFIG_SYS_DDR_TIMING_2		0x0fa880de
+#define CONFIG_SYS_DDR_CLK_CTRL		0x03000000
+#define CONFIG_SYS_DDR_MODE_1		0x80461320
+#define CONFIG_SYS_DDR_MODE_2		0x00008000
+#define CONFIG_SYS_DDR_INTERVAL		0x09480000
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x1fff_ffff	DDR		Up to 512MB cacheable
+ * 0x8000_0000 0xdfff_ffff	PCI Express Mem	1.5G non-cacheable(PCIe * 3)
+ * 0xffc0_0000 0xffc3_ffff	PCI IO range	256k non-cacheable
+ *
+ * Localbus
+ * 0xe000_0000 0xe002_0000	SSD1289		128K non-cacheable
+ * 0xec00_0000 0xefff_ffff	FLASH		Up to 64M non-cacheable
+ *
+ * 0xff90_0000 0xff97_ffff	L2 SRAM		Up to 512K cacheable
+ * 0xffd0_0000 0xffd0_3fff	init ram	16K Cacheable
+ * 0xffe0_0000 0xffef_ffff	CCSR		1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/* 64M */
+#define CONFIG_SYS_FLASH_BASE		0xec000000
+
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \
+	| BR_PS_16 | BR_V)
+
+#define CONFIG_FLASH_OR_PRELIM	0xfc0000b1
+
+#define CONFIG_SYS_SSD_BASE	0xe0000000
+#define CONFIG_SYS_SSD_BASE_PHYS	CONFIG_SYS_SSD_BASE
+#define CONFIG_SSD_BR_PRELIM	(BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \
+					BR_PS_16 | BR_V)
+#define CONFIG_SSD_OR_PRELIM	(OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
+				 OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \
+				 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM
+
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000
+/* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+/* Size of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)/* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(1024 * 1024)/* Reserved for malloc */
+
+#define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
+
+/* Serial Port
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX		1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+#define CONFIG_SYS_64BIT_VSPRINTF
+#define CONFIG_SYS_64BIT_STRTOUL
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C			/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C			/* I2C with hardware support */
+#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C spd and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+
+/*
+ * I2C2 EEPROM
+ */
+#undef CONFIG_ID_EEPROM
+
+#define CONFIG_SYS_I2C_PCA9555_ADDR	0x23
+
+/* enable read and write access to EEPROM */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#if defined(CONFIG_PCI)
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 2, direct to uli, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME		"TWR-ELEV PCIe SLOT"
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME		"mini PCIe SLOT"
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc00000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	/* do pci plug-and-play */
+#define CONFIG_E1000	/* Defind e1000 pci Ethernet card*/
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+
+#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#undef CONFIG_TSEC2
+#undef CONFIG_TSEC2_NAME
+#define CONFIG_TSEC3
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+
+#define TSEC1_PHY_ADDR	2
+#define TSEC2_PHY_ADDR	0
+#define TSEC3_PHY_ADDR	1
+
+#define TSEC1_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX	0
+#define TSEC2_PHYIDX	0
+#define TSEC3_PHYIDX	0
+
+#define CONFIG_ETHPRIME	"eTSEC1"
+
+#define CONFIG_PHY_GIGE	1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#undef CONFIG_HAS_ETH2
+#endif /* CONFIG_TSEC_ENET */
+
+#ifdef CONFIG_QE
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xefec0000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#endif /* CONFIG_QE */
+
+#ifdef CONFIG_TWR_P1025
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_MIIM_ADDRESS	(CONFIG_SYS_CCSRBAR + 0x82120)
+
+#undef CONFIG_UEC_ETH
+#define CONFIG_PHY_MODE_NEED_CHANGE
+
+#define CONFIG_UEC_ETH1	/* ETH1 */
+#define CONFIG_HAS_ETH0
+
+#ifdef CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM	0	/* UCC1 */
+#define CONFIG_SYS_UEC1_RX_CLK	QE_CLK12 /* CLK12 for MII */
+#define CONFIG_SYS_UEC1_TX_CLK	QE_CLK9 /* CLK9 for MII */
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0x18	/* 0x18 for MII */
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+#endif /* CONFIG_UEC_ETH1 */
+
+#define CONFIG_UEC_ETH5	/* ETH5 */
+#define CONFIG_HAS_ETH1
+
+#ifdef CONFIG_UEC_ETH5
+#define CONFIG_SYS_UEC5_UCC_NUM	4	/* UCC5 */
+#define CONFIG_SYS_UEC5_RX_CLK	QE_CLK_NONE
+#define CONFIG_SYS_UEC5_TX_CLK	QE_CLK13 /* CLK 13 for RMII */
+#define CONFIG_SYS_UEC5_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC5_PHY_ADDR	0x19	/* 0x19 for RMII */
+#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC5_INTERFACE_SPEED	100
+#endif /* CONFIG_UEC_ETH5 */
+#endif /* CONFIG_TWR-P1025 */
+
+/*
+ * Environment
+ */
+#ifdef CONFIG_SYS_RAMBOOT
+#ifdef CONFIG_RAMBOOT_SDCARD
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_SYS_MMC_ENV_DEV	0
+#else
+#define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE		0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR	0xfff80000
+#else
+#define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+/*
+ * USB
+ */
+#define CONFIG_HAS_FSL_DR_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB)
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#endif
+#endif
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#endif
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
+		 || defined(CONFIG_FSL_SATA)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+#undef CONFIG_WATCHDOG	/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms tick */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_HOSTNAME		unknown
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	u-boot.bin /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR	1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#define CONFIG_BOOTARGS	/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS	\
+"netdev=eth0\0"	\
+"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"	\
+"loadaddr=1000000\0"	\
+"bootfile=uImage\0"	\
+"dtbfile=twr-p1025twr.dtb\0"	\
+"ramdiskfile=rootfs.ext2.gz.uboot\0"	\
+"qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0"	\
+"tftpflash=tftpboot $loadaddr $uboot; "	\
+	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+	"erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
+	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
+	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
+	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
+"kernelflash=tftpboot $loadaddr $bootfile; "	\
+	"protect off 0xefa80000 +$filesize; "	\
+	"erase 0xefa80000 +$filesize; "	\
+	"cp.b $loadaddr 0xefa80000 $filesize; "	\
+	"protect on 0xefa80000 +$filesize; "	\
+	"cmp.b $loadaddr 0xefa80000 $filesize\0"	\
+"dtbflash=tftpboot $loadaddr $dtbfile; "	\
+	"protect off 0xefe80000 +$filesize; "	\
+	"erase 0xefe80000 +$filesize; "	\
+	"cp.b $loadaddr 0xefe80000 $filesize; "	\
+	"protect on 0xefe80000 +$filesize; "	\
+	"cmp.b $loadaddr 0xefe80000 $filesize\0"	\
+"ramdiskflash=tftpboot $loadaddr $ramdiskfile; "	\
+	"protect off 0xeeb80000 +$filesize; "	\
+	"erase 0xeeb80000 +$filesize; "	\
+	"cp.b $loadaddr 0xeeb80000 $filesize; "	\
+	"protect on 0xeeb80000 +$filesize; "	\
+	"cmp.b $loadaddr 0xeeb80000 $filesize\0"	\
+"qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; "	\
+	"protect off 0xefec0000 +$filesize; "	\
+	"erase 0xefec0000 +$filesize; "	\
+	"cp.b $loadaddr 0xefec0000 $filesize; "	\
+	"protect on 0xefec0000 +$filesize; "	\
+	"cmp.b $loadaddr 0xefec0000 $filesize\0"	\
+"consoledev=ttyS0\0"	\
+"ramdiskaddr=2000000\0"	\
+"ramdiskfile=rootfs.ext2.gz.uboot\0"	\
+"fdtaddr=c00000\0"	\
+"bdev=sda1\0"	\
+"norbootaddr=ef080000\0"	\
+"norfdtaddr=ef040000\0"	\
+"ramdisk_size=120000\0" \
+"usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \
+   "console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000"
+
+#define CONFIG_NFSBOOTCOMMAND	\
+"setenv bootargs root=/dev/nfs rw "	\
+"nfsroot=$serverip:$rootpath "	\
+"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+"console=$consoledev,$baudrate $othbootargs;" \
+"tftp $loadaddr $bootfile&&"	\
+"tftp $fdtaddr $fdtfile&&"	\
+"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_HDBOOT	\
+"setenv bootargs root=/dev/$bdev rw rootdelay=30 "	\
+"console=$consoledev,$baudrate $othbootargs;" \
+"usb start;"	\
+"ext2load usb 0:1 $loadaddr /boot/$bootfile;"	\
+"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"	\
+"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_USB_FAT_BOOT	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"usb start;"	\
+"fatload usb 0:2 $loadaddr $bootfile;"	\
+"fatload usb 0:2 $fdtaddr $fdtfile;"	\
+"fatload usb 0:2 $ramdiskaddr $ramdiskfile;"	\
+"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_USB_EXT2_BOOT	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"usb start;"	\
+"ext2load usb 0:4 $loadaddr $bootfile;"	\
+"ext2load usb 0:4 $fdtaddr $fdtfile;" \
+"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
+"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_NORBOOT	\
+"setenv bootargs root=/dev/mtdblock3 rw "	\
+"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"	\
+"bootm $norbootaddr - $norfdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND_TFTP	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"tftp $ramdiskaddr $ramdiskfile;"	\
+"tftp $loadaddr $bootfile;"	\
+"tftp $fdtaddr $fdtfile;"	\
+"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"bootm 0xefa80000 0xeeb80000 0xefe80000"
+
+#define CONFIG_BOOTCOMMAND	CONFIG_RAMBOOTCOMMAND
+
+#endif /* __CONFIG_H */
-- 
1.8.0




More information about the U-Boot mailing list