[U-Boot] [PATCH 05/15] powerpc/83xx/km: add MV88E6122 switch support for kmvect1
Holger Brunck
holger.brunck at keymile.com
Thu Jan 17 13:47:51 CET 2013
From: Karlheinz Jerg <karlheinz.jerg at keymile.com>
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection
to the switch MV88E6122. This switch has a connection to a frontport
ethernet interface. The ethernet port used for network booting is
automatically selected by u-boot. If a Piggy is plugged, the Piggy
port is selected (UEC2, eth1). If the Piggy isn't present, the
Frontport is selected (UEC0, eth0).
The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28)
and released at startup.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg at keymile.com>
Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
---
board/keymile/km83xx/km83xx.c | 78 ++++++++++++++++++++++++++++++++++++
include/configs/km/km83xx-common.h | 8 +---
include/configs/suvd3.h | 37 +++++++++++++++++
3 files changed, 117 insertions(+), 6 deletions(-)
diff --git a/board/keymile/km83xx/km83xx.c b/board/keymile/km83xx/km83xx.c
index 26e682b..0907195 100644
--- a/board/keymile/km83xx/km83xx.c
+++ b/board/keymile/km83xx/km83xx.c
@@ -215,8 +215,86 @@ int misc_init_r(void)
return 0;
}
+#if defined(CONFIG_KMVECT1)
+#include <mv88e6352.h>
+/* Marvell MV88E6122 switch configuration */
+struct mv88e_sw_reg extsw_conf[] = {
+ /* port 1, FRONT_MDI, autoneg */
+ { PORT(1), PORT_PHY, NO_SPEED_FOR },
+ { PORT(1), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ { PHY(1), PHY_1000_CTRL, NO_ADV },
+ { PHY(1), PHY_SPEC_CTRL, AUTO_MDIX_EN },
+ { PHY(1), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
+ FULL_DUPLEX },
+ /* port 2, unused */
+ { PORT(2), PORT_CTRL, PORT_DIS },
+ { PHY(2), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 3, BP_MII (CPU), PHY mode, 100BASE */
+ { PORT(3), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ /* port 4, ESTAR to slot 11, SerDes, 1000BASE-X */
+ { PORT(4), PORT_STATUS, NO_PHY_DETECT },
+ { PORT(4), PORT_PHY, SPEED_1000_FOR },
+ { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ /* port 5, ESTAR to slot 13, SerDes, 1000BASE-X */
+ { PORT(5), PORT_STATUS, NO_PHY_DETECT },
+ { PORT(5), PORT_PHY, SPEED_1000_FOR },
+ { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ /*
+ * Errata Fix: 1.9V Output from Internal 1.8V Regulator,
+ * acc . MV-S300889-00D.pdf , clause 4.5
+ */
+ { PORT(5), 0x1A, 0xADB1 },
+ /* port 6, unused, this port has no phy */
+ { PORT(6), PORT_CTRL, PORT_DIS },
+};
+#endif
+
int last_stage_init(void)
{
+#if defined(CONFIG_KMVECT1)
+ struct km_bec_fpga *base =
+ (struct km_bec_fpga *)CONFIG_SYS_KMBEC_FPGA_BASE;
+ u8 tmp_reg;
+
+ /* Release mv88e6122 from reset */
+ tmp_reg = in_8(&base->res1[0]) | 0x10; /* DIRECT3 register */
+ out_8(&base->res1[0], tmp_reg); /* GP28 as output */
+ tmp_reg = in_8(&base->gprt3) | 0x10; /* GP28 to high */
+ out_8(&base->gprt3, tmp_reg);
+
+ /* configure MV88E6122 switch */
+ char *name = "UEC2";
+
+ if (miiphy_set_current_dev(name))
+ return 0;
+
+ mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
+ ARRAY_SIZE(extsw_conf));
+
+ mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
+
+ if (piggy_present()) {
+ uchar enetaddr[6];
+ if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
+ /* increment last 3 bytes */
+ u32 val = (enetaddr[3] << 16) + (enetaddr[4] << 8)
+ + enetaddr[5];
+ val++;
+ enetaddr[3] = (val >> 16) & 0xFF;
+ enetaddr[4] = (val >> 8) & 0xFF;
+ enetaddr[5] = (val >> 0) & 0xFF;
+ if (!eth_setenv_enetaddr("eth1addr", enetaddr)) {
+ setenv("ethact", "UEC2");
+ setenv("netdev", "eth1");
+ puts("using PIGGY for network boot\n");
+ } else
+ puts("using frontport for network boot\n");
+ }
+ } else
+ puts("using frontport for network boot\n");
+#endif
+
#if defined(CONFIG_KMCOGE5NE)
struct bfticu_iomap *base =
(struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE;
diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h
index a9823d6..1e596c8 100644
--- a/include/configs/km/km83xx-common.h
+++ b/include/configs/km/km83xx-common.h
@@ -165,19 +165,15 @@
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME "UEC0"
+#if !defined(CONFIG_MPC8309)
#define CONFIG_UEC_ETH1 /* GETH1 */
#define UEC_VERBOSE_DEBUG 1
+#endif
#ifdef CONFIG_UEC_ETH1
-#if defined(CONFIG_MPC8309)
-#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK12
-#else
#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#endif
#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 0
#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h
index c50832c..bbf9da5 100644
--- a/include/configs/suvd3.h
+++ b/include/configs/suvd3.h
@@ -110,4 +110,41 @@
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+/*
+ * QE UEC ethernet configuration
+ */
+#if defined(CONFIG_KMVECT1)
+#define CONFIG_MV88E6352_SWITCH
+#define CONFIG_KM_MVEXTSW_ADDR 0x10
+
+/* ethernet port connected to simple switch 88e6122 (UEC0) */
+#define CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
+#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
+#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
+
+#define CONFIG_FIXED_PHY 0xFFFFFFFF
+#define CONFIG_SYS_FIXED_PHY_ADDR 0x1E /* unused address */
+#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \
+ {devnum, speed, duplex}
+#define CONFIG_SYS_FIXED_PHY_PORTS \
+ CONFIG_SYS_FIXED_PHY_PORT("UEC0", SPEED_100, DUPLEX_FULL)
+
+#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR CONFIG_SYS_FIXED_PHY_ADDR
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
+
+/* ethernet port connected to piggy (UEC2) */
+#define CONFIG_HAS_ETH1
+#define CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */
+#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12
+#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR 0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
+#endif /* CONFIG_KMVECT1 */
+
#endif /* __CONFIG_H */
--
1.7.1
More information about the U-Boot
mailing list