[U-Boot] [PATCH V3 2/2] arm: mx5: Add support for DENX M53EVK

Marek Vasut marex at denx.de
Fri May 3 21:56:40 CEST 2013


Dear Benoît Thébaudeau,

> Dear Marek Vasut,
> 
> On Friday, May 3, 2013 4:59:13 PM, Benoît Thébaudeau wrote:
> > Dear Marek Vasut,
> > 
> > On Thursday, April 25, 2013 10:16:03 PM, Marek Vasut wrote:
> > > Add basic support for the DENX M53EVK board. Currently supported is:
> > > MMC (incl. booting)
> > > NAND (incl. booting)
> > > Ethernet, I2C, USB, SATA, RTC.
> > > 
> > > Signed-off-by: Marek Vasut <marex at denx.de>
> > 
> > [...]
> > 
> > > diff --git a/board/denx/m53evk/m53evk.c b/board/denx/m53evk/m53evk.c
> > > new file mode 100644
> > > index 0000000..3289f28
> > > --- /dev/null
> > > +++ b/board/denx/m53evk/m53evk.c
> > > @@ -0,0 +1,408 @@
> > 
> > [...]
> > 
> > > +#ifdef CONFIG_USB_EHCI_MX5
> > > +int board_ehci_hcd_init(int port)
> > > +{
> > > +	if (port == 0) {
> > > +		/* USB OTG PWRON */
> > > +		mxc_request_iomux(MX53_PIN_GPIO_4, IOMUX_CONFIG_ALT1);
> > > +		mxc_iomux_set_pad(MX53_PIN_GPIO_4,
> > > +				PAD_CTL_PKE_ENABLE |
> > > +				PAD_CTL_100K_PD |
> > > +				PAD_CTL_DRV_HIGH
> > > +				);
> > > +		gpio_direction_output(IOMUX_TO_GPIO(MX53_PIN_GPIO_4), 0);
> > > +
> > > +		/* USB OTG Over Current */
> > > +		mxc_request_iomux(MX53_PIN_GPIO_18, IOMUX_CONFIG_ALT1);
> > > +		mxc_iomux_set_input(MX53_USBOH3_IPP_IND_OTG_OC_SELECT_INPUT, 1);
> > 
> > It looks like there is something wrong here: The last line connects
> > OTG.OC to EIM_D21.ALT6, but the line before sets GPIO_18 as GPIO7[13]
> > instead of setting
> > EIM_D21 as OTG.OC.
> 
> According to http://www.denx-cs.de/doku/?q=m53pinout , USB_OTG_OC is on
> ball D7 (i.e. GPIO_18), and ball V3 (i.e. EIM_D21) is not on the SoM
> connector.
> 
> So can you clarify what's going on with this signal? Is it handled by
> software as a GPIO, and EIM_D21 is just tied high or low on the SoM to
> make the hardware controller not complain about a false OC detection?

Yes, the OTG OC is handled by GPIO.

Best regards,
Marek Vasut


More information about the U-Boot mailing list