[U-Boot] [PATCH v3 16/25] imx: mx51_efikamx/sb: Convert to iomux-v3
Benoît Thébaudeau
benoit.thebaudeau at advansee.com
Fri May 3 22:32:28 CEST 2013
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau at advansee.com>
Tested-by: Matt Sealey <matt at genesi-usa.com>
---
Changes in v3: None
Changes in v2: None
board/genesi/mx51_efikamx/efikamx-usb.c | 122 +++++++++++++++++--------------
1 file changed, 69 insertions(+), 53 deletions(-)
diff --git a/board/genesi/mx51_efikamx/efikamx-usb.c b/board/genesi/mx51_efikamx/efikamx-usb.c
index cf020c3..cabad70 100644
--- a/board/genesi/mx51_efikamx/efikamx-usb.c
+++ b/board/genesi/mx51_efikamx/efikamx-usb.c
@@ -26,8 +26,7 @@
#include <usb.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
-#include <asm/arch/mx5x_pins.h>
-#include <asm/arch/iomux.h>
+#include <asm/arch/iomux-mx51.h>
#include <asm/gpio.h>
#include <usb/ehci-fsl.h>
#include <usb/ulpi.h>
@@ -35,40 +34,57 @@
#include "../../../drivers/usb/host/ehci.h"
-/* USB pin configuration */
-#define USB_PAD_CONFIG (PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST | \
- PAD_CTL_DRV_HIGH | PAD_CTL_100K_PU | \
- PAD_CTL_HYS_ENABLE | PAD_CTL_PUE_PULL)
-
/*
* Configure the USB H1 and USB H2 IOMUX
*/
void setup_iomux_usb(void)
{
- setup_iomux_usb_h1();
-
- if (machine_is_efikasb())
- setup_iomux_usb_h2();
-
- /* USB PHY reset */
- mxc_request_iomux(MX51_PIN_EIM_D27, IOMUX_CONFIG_ALT1);
- mxc_iomux_set_pad(MX51_PIN_EIM_D27, PAD_CTL_PKE_ENABLE |
- PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH);
-
- /* USB HUB reset */
- mxc_request_iomux(MX51_PIN_GPIO1_5, IOMUX_CONFIG_ALT0);
- mxc_iomux_set_pad(MX51_PIN_GPIO1_5, PAD_CTL_PKE_ENABLE |
- PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH);
-
- /* WIFI EN (act low) */
- mxc_request_iomux(MX51_PIN_EIM_A22, IOMUX_CONFIG_GPIO);
- mxc_iomux_set_pad(MX51_PIN_EIM_A22, 0);
- /* WIFI RESET */
- mxc_request_iomux(MX51_PIN_EIM_A16, IOMUX_CONFIG_GPIO);
- mxc_iomux_set_pad(MX51_PIN_EIM_A16, 0);
- /* BT EN (act low) */
- mxc_request_iomux(MX51_PIN_EIM_A17, IOMUX_CONFIG_GPIO);
- mxc_iomux_set_pad(MX51_PIN_EIM_A17, 0);
+ static const iomux_v3_cfg_t usb_h1_pads[] = {
+ MX51_PAD_USBH1_CLK__USBH1_CLK,
+ MX51_PAD_USBH1_DIR__USBH1_DIR,
+ MX51_PAD_USBH1_STP__USBH1_STP,
+ MX51_PAD_USBH1_NXT__USBH1_NXT,
+ MX51_PAD_USBH1_DATA0__USBH1_DATA0,
+ MX51_PAD_USBH1_DATA1__USBH1_DATA1,
+ MX51_PAD_USBH1_DATA2__USBH1_DATA2,
+ MX51_PAD_USBH1_DATA3__USBH1_DATA3,
+ MX51_PAD_USBH1_DATA4__USBH1_DATA4,
+ MX51_PAD_USBH1_DATA5__USBH1_DATA5,
+ MX51_PAD_USBH1_DATA6__USBH1_DATA6,
+ MX51_PAD_USBH1_DATA7__USBH1_DATA7,
+ };
+
+ static const iomux_v3_cfg_t usb_pads[] = {
+ MX51_PAD_EIM_D27__GPIO2_9, /* USB PHY reset */
+ MX51_PAD_GPIO1_5__GPIO1_5, /* USB HUB reset */
+ NEW_PAD_CTRL(MX51_PAD_EIM_A22__GPIO2_16, 0), /* WIFI /EN */
+ NEW_PAD_CTRL(MX51_PAD_EIM_A16__GPIO2_10, 0), /* WIFI RESET */
+ NEW_PAD_CTRL(MX51_PAD_EIM_A17__GPIO2_11, 0), /* BT /EN */
+ };
+
+ imx_iomux_v3_setup_multiple_pads(usb_h1_pads, ARRAY_SIZE(usb_h1_pads));
+
+ if (machine_is_efikasb()) {
+ static const iomux_v3_cfg_t usb_h2_pads[] = {
+ MX51_PAD_EIM_A24__USBH2_CLK,
+ MX51_PAD_EIM_A25__USBH2_DIR,
+ MX51_PAD_EIM_A26__USBH2_STP,
+ MX51_PAD_EIM_A27__USBH2_NXT,
+ MX51_PAD_EIM_D16__USBH2_DATA0,
+ MX51_PAD_EIM_D17__USBH2_DATA1,
+ MX51_PAD_EIM_D18__USBH2_DATA2,
+ MX51_PAD_EIM_D19__USBH2_DATA3,
+ MX51_PAD_EIM_D20__USBH2_DATA4,
+ MX51_PAD_EIM_D21__USBH2_DATA5,
+ MX51_PAD_EIM_D22__USBH2_DATA6,
+ MX51_PAD_EIM_D23__USBH2_DATA7,
+ };
+
+ imx_iomux_v3_setup_multiple_pads(usb_h2_pads,
+ ARRAY_SIZE(usb_h2_pads));
+ }
+
+ imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads));
}
/*
@@ -77,18 +93,18 @@ void setup_iomux_usb(void)
static void efika_usb_enable_devices(void)
{
/* Enable Bluetooth */
- gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A17), 0);
+ gpio_direction_output(IMX_GPIO_NR(2, 11), 0);
udelay(10000);
- gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A17), 1);
+ gpio_set_value(IMX_GPIO_NR(2, 11), 1);
/* Enable WiFi */
- gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A22), 1);
+ gpio_direction_output(IMX_GPIO_NR(2, 16), 1);
udelay(10000);
/* Reset the WiFi chip */
- gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A16), 0);
+ gpio_direction_output(IMX_GPIO_NR(2, 10), 0);
udelay(10000);
- gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A16), 1);
+ gpio_set_value(IMX_GPIO_NR(2, 10), 1);
}
/*
@@ -97,11 +113,11 @@ static void efika_usb_enable_devices(void)
static void efika_usb_hub_reset(void)
{
/* HUB reset */
- gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 1);
+ gpio_direction_output(IMX_GPIO_NR(1, 5), 1);
udelay(1000);
- gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 0);
+ gpio_set_value(IMX_GPIO_NR(1, 5), 0);
udelay(1000);
- gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 1);
+ gpio_set_value(IMX_GPIO_NR(1, 5), 1);
}
/*
@@ -110,28 +126,26 @@ static void efika_usb_hub_reset(void)
static void efika_usb_phy_reset(void)
{
/* SMSC 3317 PHY reset */
- gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_D27), 0);
+ gpio_direction_output(IMX_GPIO_NR(2, 9), 0);
udelay(1000);
- gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_D27), 1);
+ gpio_set_value(IMX_GPIO_NR(2, 9), 1);
}
static void efika_ehci_init(struct usb_ehci *ehci, uint32_t stp_gpio,
- uint32_t alt0, uint32_t alt1)
+ iomux_v3_cfg_t stp_pad_gpio,
+ iomux_v3_cfg_t stp_pad_usb)
{
int ret;
struct ulpi_regs *ulpi = (struct ulpi_regs *)0;
struct ulpi_viewport ulpi_vp;
- mxc_request_iomux(stp_gpio, alt0);
- mxc_iomux_set_pad(stp_gpio, PAD_CTL_DRV_HIGH |
- PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST);
- gpio_direction_output(IOMUX_TO_GPIO(stp_gpio), 0);
+ imx_iomux_v3_setup_pad(stp_pad_gpio);
+ gpio_direction_output(stp_gpio, 0);
udelay(1000);
- gpio_set_value(IOMUX_TO_GPIO(stp_gpio), 1);
+ gpio_set_value(stp_gpio, 1);
udelay(1000);
- mxc_request_iomux(stp_gpio, alt1);
- mxc_iomux_set_pad(stp_gpio, USB_PAD_CONFIG);
+ imx_iomux_v3_setup_pad(stp_pad_usb);
udelay(10000);
ulpi_vp.viewport_addr = (u32)&ehci->ulpi_viewpoint;
@@ -204,11 +218,13 @@ void board_ehci_hcd_postinit(struct usb_ehci *ehci, int port)
tmp = (tmp & ~0x3) | 0x01;
writel(tmp, OTG_BASE_ADDR + 0x80c);
} else if (port == 1) {
- efika_ehci_init(ehci, MX51_PIN_USBH1_STP,
- IOMUX_CONFIG_ALT2, IOMUX_CONFIG_ALT0);
+ efika_ehci_init(ehci, IMX_GPIO_NR(1, 27),
+ MX51_PAD_USBH1_STP__GPIO1_27,
+ MX51_PAD_USBH1_STP__USBH1_STP);
} else if ((port == 2) && machine_is_efikasb()) {
- efika_ehci_init(ehci, MX51_PIN_EIM_A26,
- IOMUX_CONFIG_ALT1, IOMUX_CONFIG_ALT2);
+ efika_ehci_init(ehci, IMX_GPIO_NR(2, 20),
+ MX51_PAD_EIM_A26__GPIO2_20,
+ MX51_PAD_EIM_A26__USBH2_STP);
}
if (port)
--
1.7.10.4
More information about the U-Boot
mailing list