[U-Boot] [PATCH] powerpc/p1022ds: boot from SD Card with SPL
ying.zhang at freescale.com
ying.zhang at freescale.com
Wed May 15 11:14:19 CEST 2013
From: Ying Zhang <b40530 at freescale.com>
This patch introduces SPL to enable a loader stub that runs in the L2 SRAM,
after being loaded by the code from the internal on-chip ROM. It loads the
final uboot image into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so
that ddr spd code can get the interleaving mode setting in env. It
loads final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions
enabled.
This patch is on top of the following patch:
1. common/Makefile: Add new symbol CONFIG_SPL_ENV_SUPPORT for environment
in SPL.
2. powerpc/mpc85xx: support application without resetvec segment in the
linker script.
3. Add the symbol for the minimal SPL used to eliminate unused code
4. drivers/mmc: move spl_mmc.c to common/spl
5. Makefile: move the common makefile line to public area
6. powerpc/mpc85xx: modify the function clear_bss and the end address of
the BSS
Signed-off-by: Ying Zhang <b40530 at freescale.com>
---
Compared with the previous version, this patch stripped out the independent
part with SD boot.
README | 8 ++
arch/powerpc/cpu/mpc85xx/u-boot-spl.lds | 5 +
board/freescale/common/Makefile | 2 -
board/freescale/p1022ds/Makefile | 3 +
board/freescale/p1022ds/spl.c | 112 ++++++++++++++++++++++++++
board/freescale/p1022ds/tlb.c | 9 ++-
doc/README.mpc85xx-sd-spi-boot | 82 +++++++++++++++++++
drivers/mmc/Makefile | 1 +
drivers/mmc/fsl_esdhc_spl.c | 132 +++++++++++++++++++++++++++++++
include/configs/P1022DS.h | 56 +++++++++++--
include/fsl_esdhc.h | 1 +
spl/Makefile | 3 +
12 files changed, 403 insertions(+), 11 deletions(-)
create mode 100644 board/freescale/p1022ds/spl.c
create mode 100644 doc/README.mpc85xx-sd-spi-boot
create mode 100644 drivers/mmc/fsl_esdhc_spl.c
diff --git a/README b/README
index 79ccfc9..676bb99 100644
--- a/README
+++ b/README
@@ -2942,6 +2942,14 @@ FIT uImage format:
Support for NAND boot using simple NAND drivers that
expose the cmd_ctrl() interface.
+ CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+ Set for the SPL on PPC mpc8xxx targets, support for
+ arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+
+ CONFIG_SPL_COMMON_INIT_DDR
+ Set for common ddr init with serial presence detect in
+ SPL binary.
+
CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
diff --git a/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds b/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds
index 847818a..ba28656 100644
--- a/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds
+++ b/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds
@@ -57,6 +57,11 @@ SECTIONS
}
_edata = .;
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
. = ALIGN(8);
__init_begin = .;
__init_end = .;
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 72bb56c..c334797 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -52,9 +52,7 @@ COBJS-$(CONFIG_MPC8555CDS) += cds_pci_ft.o
COBJS-$(CONFIG_MPC8536DS) += ics307_clk.o
COBJS-$(CONFIG_MPC8572DS) += ics307_clk.o
-ifndef CONFIG_SPL_BUILD
COBJS-$(CONFIG_P1022DS) += ics307_clk.o
-endif
COBJS-$(CONFIG_P2020DS) += ics307_clk.o
COBJS-$(CONFIG_P3041DS) += ics307_clk.o
COBJS-$(CONFIG_P4080DS) += ics307_clk.o
diff --git a/board/freescale/p1022ds/Makefile b/board/freescale/p1022ds/Makefile
index 0eeef05..9746063 100644
--- a/board/freescale/p1022ds/Makefile
+++ b/board/freescale/p1022ds/Makefile
@@ -24,6 +24,9 @@ ifdef MINIMAL
COBJS-y += spl_minimal.o tlb.o law.o
else
+ifdef CONFIG_SPL_BUILD
+COBJS-y += spl.o
+endif
COBJS-y += $(BOARD).o
COBJS-y += ddr.o
COBJS-y += law.o
diff --git a/board/freescale/p1022ds/spl.c b/board/freescale/p1022ds/spl.c
new file mode 100644
index 0000000..a6c6828
--- /dev/null
+++ b/board/freescale/p1022ds/spl.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <i2c.h>
+#include "../common/ngpixis.h"
+#include <fsl_esdhc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const u32 sysclk_tbl[] = {
+ 66666000, 7499900, 83332500, 8999900,
+ 99999000, 11111000, 12499800, 13333200
+};
+
+ulong get_effective_memsize(void)
+{
+ return CONFIG_SYS_L2_SIZE;
+}
+
+void board_init_f(ulong bootflag)
+{
+ int px_spd;
+ u32 plat_ratio, sys_clk, bus_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ console_init_f();
+
+ /* Set pmuxcr to allow both i2c1 and i2c2 */
+ setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
+ setbits_be32(&gur->pmuxcr,
+ in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
+
+ /* Read back the register to synchronize the write. */
+ in_be32(&gur->pmuxcr);
+
+ /* initialize selected port with appropriate baud rate */
+ px_spd = in_8((unsigned char *)(PIXIS_BASE + PIXIS_SPD));
+ sys_clk = sysclk_tbl[px_spd & PIXIS_SPD_SYSCLK_MASK];
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ bus_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ bus_clk / 16 / CONFIG_BAUDRATE);
+#ifdef CONFIG_SPL_MMC_BOOT
+ puts("\nSD boot...\n");
+#endif
+
+ /* copy code to RAM and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SPL_RELOC_STACK, 0,
+ CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ /* Pointer is writable since we allocated a register for it */
+ gd = (gd_t *)CONFIG_SPL_GD_ADDR;
+ bd_t *bd;
+
+ memset(gd, 0, sizeof(gd_t));
+ bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L2_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, \
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+ env_init();
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+#endif
+ /* relocate environment function pointers etc. */
+ env_relocate();
+
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ gd->ram_size = initdram(0);
+ puts("Second program loader running in sram...\n");
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#endif
+}
diff --git a/board/freescale/p1022ds/tlb.c b/board/freescale/p1022ds/tlb.c
index 3acc449..9b14c37 100644
--- a/board/freescale/p1022ds/tlb.c
+++ b/board/freescale/p1022ds/tlb.c
@@ -74,7 +74,8 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 7, BOOKE_PAGESZ_4K, 1),
-#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL)
+#if defined(CONFIG_SYS_RAMBOOT) || \
+ (defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR))
/* **** - eSDHC/eSPI/NAND boot */
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
@@ -93,6 +94,12 @@ struct fsl_e_tlb_entry tlb_table[] = {
0, 10, BOOKE_PAGESZ_16K, 1),
#endif
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+ /* *I*G - L2SRAM */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 11, BOOKE_PAGESZ_256K, 1)
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/doc/README.mpc85xx-sd-spi-boot b/doc/README.mpc85xx-sd-spi-boot
new file mode 100644
index 0000000..b55eea8
--- /dev/null
+++ b/doc/README.mpc85xx-sd-spi-boot
@@ -0,0 +1,82 @@
+----------------------------------------
+Booting from On-Chip ROM (eSDHC or eSPI)
+----------------------------------------
+
+boot_format is a tool to write SD bootable images to a filesystem and build
+SD/SPI images to a binary file for writing later.
+
+When booting from an SD card/MMC, boot_format puts the configuration file and
+the RAM-based U-Boot image on the card.
+When booting from an EEPROM, boot_format generates a binary image that is used
+to boot from this EEPROM.
+
+Where to get boot_format:
+========================
+
+you can browse it online at:
+http://git.freescale.com/git/cgit.cgi/ppc/sdk/boot-format.git/
+
+Building
+========
+
+Run the following to build this project
+
+ $ make
+
+Execution
+=========
+
+boot_format runs under a regular Linux machine and requires a super user mode
+to run. Execute boot_format as follows.
+
+For building SD images by writing directly to a file system on SD media:
+
+ $ boot_format $config u-boot.bin -sd $device
+
+Where $config is the included config.dat file for your platform and $device
+is the target block device for the SD media on your computer.
+
+For build binary images directly a local file:
+
+ $ boot_format $config u-boot.bin -spi $file
+
+Where $file is the target file. Also keep in mind the u-boot.bin file needs
+to be the u-boot built for your particular platform and target media.
+
+Example: To generate a u-boot.bin for a P1022DS booting from SD, run the
+following in the u-boot repository:
+
+ $ make P1022DS_SDCARD
+
+Configuration Files
+===================
+
+Below are the configuration files to be used with a particular platform. Keep
+in mind that some of these config files are tied to the platforms DDR speed.
+Please see the SoC reference manual for more documentation.
+
+P1022DS config_sram_p1022ds.dat
+P2020DS config_sram_p2020ds.dat
+P2010DS config_sram_p2020ds.dat
+P1020RDB config_ddr2_1g_p1020rdb_533M.dat
+P1020RDB config_ddr2_1g_p1020rdb_667M.dat
+P2020RDB config_ddr2_1g_p2020rdb_800M.dat
+P2020RDB config_ddr2_1g_p2020rdb_667M.dat
+P2020RDB config_ddr3_1gb_64bit_p2020rdb_pc.dat
+P2010RDB config_ddr3_1gb_64bit_p2020rdb_pc.dat
+P1020RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1011RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1010RDB config_ddr3_1gb_p1010rdb_800M.dat
+P1014RDB config_ddr3_1gb_p1014rdb_800M.dat
+P1021RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1012RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1022DS config_ddr3_2gb_p1022ds.dat
+P1013DS config_ddr3_2gb_p1022ds.dat
+P1024RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1013RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1025RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1016RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1020UTM config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1020MBG config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+MPC8536DS config_ddr2_512m_mpc8536ds_667M.dat
+
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index 196ef9b..39a6bc2 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -47,6 +47,7 @@ COBJS-$(CONFIG_SPEAR_SDHCI) += spear_sdhci.o
COBJS-$(CONFIG_TEGRA_MMC) += tegra_mmc.o
COBJS-$(CONFIG_DWMMC) += dw_mmc.o
COBJS-$(CONFIG_EXYNOS_DWMMC) += exynos_dw_mmc.o
+COBJS-$(CONFIG_SPL_MMC_SUPPORT) += fsl_esdhc_spl.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --git a/drivers/mmc/fsl_esdhc_spl.c b/drivers/mmc/fsl_esdhc_spl.c
new file mode 100644
index 0000000..f3dd92c
--- /dev/null
+++ b/drivers/mmc/fsl_esdhc_spl.c
@@ -0,0 +1,132 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <mmc.h>
+#include <malloc.h>
+
+/*
+ * The environment variables are written to just after the u-boot image
+ * on SDCard, so we must read the MBR to get the start address and code
+ * length of the u-boot image, then calculate the address of the env.
+ */
+#define ESDHC_BOOT_IMAGE_SIZE 0x48
+#define ESDHC_BOOT_IMAGE_ADDR 0x50
+#define MBRDBR_BOOT_SIG_55 0x1fe
+#define MBRDBR_BOOT_SIG_AA 0x1ff
+#define CONFIG_CFG_DATA_SECTOR 0
+
+/*
+ * The main entry for mmc booting. It's necessary that SDRAM is already
+ * configured and available since this code loads the main U-Boot image
+ * from mmc into SDRAM and starts it from there.
+ */
+
+void mmc_boot(void)
+{
+ __attribute__((noreturn)) void (*uboot)(void);
+ uint blk_start, blk_cnt, err;
+ u32 blklen;
+ uchar *tmp_buf;
+ uchar val;
+ uint i, byte_num;
+ u32 offset, code_len;
+ struct mmc *mmc;
+
+ mmc = find_mmc_device(0);
+ if (!mmc) {
+ puts("spl: mmc device not found!!\n");
+ hang();
+ }
+
+ blklen = mmc->read_bl_len;
+ tmp_buf = malloc(blklen);
+ if (!tmp_buf) {
+ puts("spl: malloc memory failed!!\n");
+ hang();
+ }
+ memset(tmp_buf, 0, blklen);
+
+ /*
+ * Read source addr from sd card
+ */
+ err = mmc->block_dev.block_read(0, CONFIG_CFG_DATA_SECTOR, \
+ 1, tmp_buf);
+ if (err != 1) {
+ puts("spl: mmc read failed!!\n");
+ free(tmp_buf);
+ hang();
+ }
+
+ val = *(tmp_buf + MBRDBR_BOOT_SIG_55);
+ if (0x55 != val) {
+ puts("spl: mmc signature is not valid!!\n");
+ free(tmp_buf);
+ hang();
+ }
+ val = *(tmp_buf + MBRDBR_BOOT_SIG_AA);
+ if (0xAA != val) {
+ puts("spl: mmc signature is not valid!!\n");
+ free(tmp_buf);
+ hang();
+ }
+
+ byte_num = 4;
+ offset = 0;
+ for (i = 0; i < byte_num; i++) {
+ val = *(tmp_buf + ESDHC_BOOT_IMAGE_ADDR + i);
+ offset = (offset << 8) + val;
+ }
+ offset += CONFIG_SYS_MMC_U_BOOT_OFFS;
+ /* Get the code size from offset 0x48 */
+ byte_num = 4;
+ code_len = 0;
+ for (i = 0; i < byte_num; i++) {
+ val = *(tmp_buf + ESDHC_BOOT_IMAGE_SIZE + i);
+ code_len = (code_len << 8) + val;
+ }
+ code_len -= CONFIG_SYS_MMC_U_BOOT_OFFS;
+ /*
+ * Load U-Boot image from mmc into RAM
+ */
+ blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len;
+ blk_cnt = ALIGN(code_len, mmc->read_bl_len) / mmc->read_bl_len;
+ err = mmc->block_dev.block_read(0, blk_start, blk_cnt,
+ (uchar *)CONFIG_SYS_MMC_U_BOOT_DST);
+ if (err != blk_cnt) {
+ puts("spl: mmc read failed!!\n");
+ free(tmp_buf);
+ hang();
+ }
+
+ /*
+ * Clean d-cache and invalidate i-cache, to
+ * make sure that no stale data is executed.
+ */
+ flush_cache(CONFIG_SYS_MMC_U_BOOT_DST, CONFIG_SYS_MMC_U_BOOT_SIZE);
+
+ /*
+ * Jump to U-Boot image
+ */
+ uboot = (void *)CONFIG_SYS_MMC_U_BOOT_START;
+ (*uboot)();
+}
+
diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h
index 1cefed9..09c89e8 100644
--- a/include/configs/P1022DS.h
+++ b/include/configs/P1022DS.h
@@ -19,11 +19,32 @@
#endif
#ifdef CONFIG_SDCARD
-#define CONFIG_RAMBOOT_SDCARD
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE 0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+#define CONFIG_SPL_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_PAD_TO 0x18000
+#define CONFIG_SPL_MAX_SIZE (96 * 1024)
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (512 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000)
+#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (96 << 10)
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SPL_MMC_BOOT
+#endif
#endif
#ifdef CONFIG_SPIFLASH
@@ -298,6 +319,24 @@
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
/*
+ * Config the L2 Cache as L2 SRAM
+ */
+#if defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_SDCARD)
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_L2_SIZE (256 << 10)
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 128 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10)
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 160 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (96 << 10)
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024)
+#endif
+#endif
+
+/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
@@ -305,7 +344,7 @@
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_SPL_BUILD_MINIMAL
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif
@@ -528,7 +567,7 @@
/*
* Environment
*/
-#ifdef CONFIG_RAMBOOT_SPIFLASH
+#ifdef CONFIG_SPIFLASH
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
@@ -537,8 +576,9 @@
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
-#elif defined(CONFIG_RAMBOOT_SDCARD)
+#elif defined(CONFIG_SDCARD)
#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_MMC_ENV_DEV 0
#elif defined(CONFIG_NAND)
diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
index 67d6057..b17c424 100644
--- a/include/fsl_esdhc.h
+++ b/include/fsl_esdhc.h
@@ -198,5 +198,6 @@ void fdt_fixup_esdhc(void *blob, bd_t *bd);
static inline int fsl_esdhc_mmc_init(bd_t *bis) { return -ENOSYS; }
static inline void fdt_fixup_esdhc(void *blob, bd_t *bd) {}
#endif /* CONFIG_FSL_ESDHC */
+void mmc_boot(void);
#endif /* __FSL_ESDHC_H__ */
diff --git a/spl/Makefile b/spl/Makefile
index b5a8de7..7187d68 100644
--- a/spl/Makefile
+++ b/spl/Makefile
@@ -51,6 +51,9 @@ LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o
endif
ifeq ($(CPU),mpc85xx)
LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o
+ifdef CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+LIBS-y += arch/powerpc/cpu/mpc8xxx/ddr/libddr.o
+endif
endif
ifeq ($(CPU),mpc86xx)
LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o
--
1.7.0.4
More information about the U-Boot
mailing list