[U-Boot] [PATCH] powerpc/CoreNet: Allow pbl images to take u-boot images != 512K

[Chris Packham]

From: Chris Packham <chris.packham at alliedtelesis.co.nz>

Instead of assuming that SYS_TEXT_BASE is 0xFFF80000 calculate the initial
pbl command offset by subtracting the image size from the top of the
24-bit address range. Also increase the size of the memory buffer to
accommodate a larger output image.

Signed-off-by: Chris Packham <chris.packham at alliedtelesis.co.nz>
---
Hi,

I was trying to get a SPIFLASH image working for my board based on a P2040 and
found that the pblimage tool assumes that u-boot.bin is always 512K. In my case
it's actually larger. This patch is my attempt to allow for an arbitrary
u-boot.bin image size.

Thanks,
Chris

 tools/pblimage.c |   33 ++++++++++++++++++++++++++-------
 1 file changed, 26 insertions(+), 7 deletions(-)

diff --git a/tools/pblimage.c b/tools/pblimage.c
index 508a747..3582ada 100644
--- a/tools/pblimage.c
+++ b/tools/pblimage.c
@@ -26,18 +26,14 @@
 #include "pblimage.h"
 
 /*
- * The PBL can load up to 64 bytes at a time, so we split the U-Boot
- * image into 64 byte chunks. PBL needs a command for each piece, of
- * the form "81xxxxxx", where "xxxxxx" is the offset. SYS_TEXT_BASE
- * is 0xFFF80000 for PBL boot, and PBL only cares about low 24-bit,
- * so it starts from 0x81F80000.
+ * Initialize to an invalid value.
  */
-static uint32_t next_pbl_cmd = 0x81F80000;
+static uint32_t next_pbl_cmd = 0x82000000;
 /*
  * need to store all bytes in memory for calculating crc32, then write the
  * bytes to image file for PBL boot.
  */
-static unsigned char mem_buf[600000];
+static unsigned char mem_buf[1000000];
 static unsigned char *pmem_buf = mem_buf;
 static int pbl_size;
 static char *fname = "Unknown";
@@ -52,6 +48,28 @@ static union
 
 #define ENDIANNESS ((char)endian_test.l)
 
+/*
+ * The PBL can load up to 64 bytes at a time, so we split the U-Boot
+ * image into 64 byte chunks. PBL needs a command for each piece, of
+ * the form "81xxxxxx", where "xxxxxx" is the offset. Calculate the
+ * start offset by subtracting the size of the u-boot image from the
+ * top of the allowable 24-bit range.
+ */
+static void init_next_pbl_cmd(FILE *fp_uboot)
+{
+	struct stat st;
+	int fd = fileno(fp_uboot);
+	size_t size;
+
+	if (fstat(fd, &st) == -1) {
+		printf("Error: Could not determine u-boot image size. %s\n",
+			strerror(errno));
+		exit(EXIT_FAILURE);
+	}
+
+	next_pbl_cmd = 0x82000000 - st.st_size;
+}
+
 static void generate_pbl_cmd(void)
 {
 	uint32_t val = next_pbl_cmd;
@@ -80,6 +98,7 @@ static void pbl_fget(size_t size, FILE *stream)
 /* load split u-boot with PBI command 81xxxxxx. */
 static void load_uboot(FILE *fp_uboot)
 {
+	init_next_pbl_cmd(fp_uboot);
 	while (next_pbl_cmd < 0x82000000) {
 		generate_pbl_cmd();
 		pbl_fget(64, fp_uboot);
-- 
1.7.9.5