[U-Boot] [PATCH v1 1/7] TI: armv7: move board specific NAND configs out from ti_armv7_common.h and ti_am335x_common.h
Pekon Gupta
pekon at ti.com
Fri Jul 4 21:05:11 CEST 2014
This patch moves some board specific NAND configs:
- FROM: generic config files like 'ti_armv7_common.h' and 'ti_am335x_common.h'
- TO: individual board config files using these configs.
So that each board can independently set the value as per its design.
Following configs are affected in this patch:
CONFIG_NAND_OMAP_GPMC: <refer doc/README.nand>
CONFIG_NAND_OMAP_ELM: <refer doc/README.nand>
CONFIG_SPL_NAND_AM33XX_BCH: <refer doc/README.nand>
CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>
This patch also updates documentation for few of above NAND configs.
Signed-off-by: Pekon Gupta <pekon at ti.com>
---
doc/README.nand | 12 ++++++++++++
include/configs/am335x_evm.h | 7 +++++++
include/configs/cm_t335.h | 10 ++++++++++
include/configs/omap3_beagle.h | 6 ++++++
include/configs/omap3_igep00x0.h | 9 +++++++++
include/configs/omap3_overo.h | 8 ++++++++
include/configs/omap3_zoom1.h | 7 +++++++
include/configs/pengwyn.h | 7 +++++++
include/configs/ti_am335x_common.h | 4 ----
include/configs/ti_armv7_common.h | 9 ---------
10 files changed, 66 insertions(+), 13 deletions(-)
diff --git a/doc/README.nand b/doc/README.nand
index 70cf768..e29188f 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -89,6 +89,10 @@ Commands:
Configuration Options:
+ CONFIG_SYS_NAND_U_BOOT_OFFS
+ NAND Offset from where SPL will read u-boot image. This is the starting
+ address of u-boot MTD partition in NAND.
+
CONFIG_CMD_NAND
Enables NAND support and commmands.
@@ -226,6 +230,14 @@ Platform specific options
detection. However ECC calculation on such plaforms would still be
done by GPMC controller.
+ CONFIG_SPL_NAND_AM33XX_BCH
+ Enables SPL-NAND driver (am335x_spl_bch.c) which supports ELM based
+ hardware ECC correction. This is useful for platforms which have ELM
+ hardware engine and use NAND boot mode.
+ Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+ so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
+ SPL-NAND driver with software ECC correction support.
+
CONFIG_NAND_OMAP_ECCSCHEME
On OMAP platforms, this CONFIG specifies NAND ECC scheme.
It can take following values:
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index a48b386..57a6cab 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -233,6 +233,8 @@
#ifdef CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SPL_NAND_AM33XX_BCH
+/* NAND: device related configs */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
@@ -254,6 +256,11 @@
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#ifdef CONFIG_SPL_OS_BOOT
+ #define CONFIG_CMD_SPL_NAND_OFS 0x00080000 /* os parameters */
+ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 /* kernel offset */
+ #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#endif
#endif
diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h
index 4d1dd28..70b6e90 100644
--- a/include/configs/cm_t335.h
+++ b/include/configs/cm_t335.h
@@ -150,6 +150,16 @@
#define CONFIG_ENV_OFFSET 0x300000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SYS_NAND_ONFI_DETECTION
+/* NAND: driver related configs */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SPL_NAND_AM33XX_BCH /* SPL-NAND driver with ELM support */
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+ #define CONFIG_CMD_SPL_NAND_OFS 0x400000 /* un-assigned: (using dtb) */
+ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x500000
+ #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
/* GPIO pin + bank to pin ID mapping */
#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin)
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index c023483..7878765 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -126,6 +126,12 @@
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x240000
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x80200000\0" \
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index 79daabd..7daaef5 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -187,6 +187,15 @@
/* NAND boot config */
#ifdef CONFIG_NAND
+#define CONFIG_NAND_OMAP_GPMC
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+ #define CONFIG_CMD_SPL_NAND_OFS 0x240000
+ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+ #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+/* NAND: device related configs */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index f7483a0..a879d72 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -206,6 +206,14 @@
#define CONFIG_SYS_CACHELINE_SIZE 64
/* NAND boot config */
+#define CONFIG_NAND_OMAP_GPMC
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+ #define CONFIG_CMD_SPL_NAND_OFS 0x240000
+ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+ #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
+/* NAND: device related configs */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 3efe4cf..409be31 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -69,6 +69,13 @@
"1920k(u-boot),128k(u-boot-env),"\
"4m(kernel),-(fs)"
+#define CONFIG_NAND_OMAP_GPMC
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+ #define CONFIG_CMD_SPL_NAND_OFS 0x240000
+ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+ #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#if defined(CONFIG_CMD_NAND)
#define CONFIG_CMD_NAND_LOCK_UNLOCK /* Enable lock/unlock support */
#endif
diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h
index 8510405..f758cf9 100644
--- a/include/configs/pengwyn.h
+++ b/include/configs/pengwyn.h
@@ -127,6 +127,7 @@
#define CONFIG_CMD_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SPL_NAND_AM33XX_BCH
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
@@ -159,6 +160,12 @@
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+ #define CONFIG_CMD_SPL_NAND_OFS 0x240000 /* un-assigned */
+ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+ #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
/*
* USB configuration. We enable MUSB support, both for host and for
diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h
index 80976e7..12fceb7 100644
--- a/include/configs/ti_am335x_common.h
+++ b/include/configs/ti_am335x_common.h
@@ -84,10 +84,6 @@
#define CONFIG_BOARD_EARLY_INIT_F
#endif
-#ifdef CONFIG_NAND
-#define CONFIG_SPL_NAND_AM33XX_BCH /* ELM support */
-#endif
-
/* Now bring in the rest of the common code. */
#include <configs/ti_armv7_common.h>
diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h
index 6e0bf09..c901522 100644
--- a/include/configs/ti_armv7_common.h
+++ b/include/configs/ti_armv7_common.h
@@ -110,7 +110,6 @@
* access CS0 at is 0x8000000.
*/
#ifdef CONFIG_NAND
-#define CONFIG_NAND_OMAP_GPMC
#ifndef CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_NAND_BASE 0x8000000
#endif
@@ -243,13 +242,6 @@
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
-/* NAND */
-#ifdef CONFIG_NAND
-#define CONFIG_CMD_SPL_NAND_OFS 0x240000 /* end of u-boot */
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
-#endif
-
/* spl export command */
#define CONFIG_CMD_SPL
#endif
@@ -275,7 +267,6 @@
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_MTD_SUPPORT
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#endif
#endif /* !CONFIG_NOR_BOOT */
--
1.8.5.1.163.gd7aced9
More information about the U-Boot
mailing list