[U-Boot] [PATCH 1/9] phy: add support for bcm6368 usbh phy
Daniel Schwierzeck
daniel.schwierzeck at gmail.com
Sun Feb 4 18:32:50 UTC 2018
On 04.02.2018 11:19, Álvaro Fernández Rojas wrote:
> Signed-off-by: Álvaro Fernández Rojas <noltari at gmail.com>
> ---
> drivers/phy/Kconfig | 6 ++
> drivers/phy/Makefile | 1 +
> drivers/phy/bcm6368-usbh-phy.c | 203 +++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 210 insertions(+)
> create mode 100644 drivers/phy/bcm6368-usbh-phy.c
>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck at gmail.com>
nits below
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 43fb4c9bfd..d3fa9ded2a 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -71,6 +71,12 @@ config BCM6358_USBH_PHY
> help
> Support for the Broadcom MIPS BCM6358 USBH PHY.
>
> +config BCM6368_USBH_PHY
> + bool "BCM6368 USBH PHY support"
> + depends on PHY && ARCH_BMIPS
> + help
> + Support for the Broadcom MIPS BCM6368 USBH PHY.
> +
> config PIPE3_PHY
> bool "Support omap's PIPE3 PHY"
> depends on PHY && ARCH_OMAP2PLUS
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index 04843fd49b..d8239854a3 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_$(SPL_)PHY) += phy-uclass.o
> obj-$(CONFIG_$(SPL_)NOP_PHY) += nop-phy.o
> obj-$(CONFIG_BCM6348_USBH_PHY) += bcm6348-usbh-phy.o
> obj-$(CONFIG_BCM6358_USBH_PHY) += bcm6358-usbh-phy.o
> +obj-$(CONFIG_BCM6368_USBH_PHY) += bcm6368-usbh-phy.o
> obj-$(CONFIG_PHY_SANDBOX) += sandbox-phy.o
> obj-$(CONFIG_$(SPL_)PIPE3_PHY) += ti-pipe3-phy.o
> obj-$(CONFIG_STI_USB_PHY) += sti_usb_phy.o
> diff --git a/drivers/phy/bcm6368-usbh-phy.c b/drivers/phy/bcm6368-usbh-phy.c
> new file mode 100644
> index 0000000000..93577b30ba
> --- /dev/null
> +++ b/drivers/phy/bcm6368-usbh-phy.c
> @@ -0,0 +1,203 @@
> +/*
> + * Copyright (C) 2018 Álvaro Fernández Rojas <noltari at gmail.com>
> + *
> + * Derived from linux/arch/mips/bcm63xx/usb-common.c:
> + * Copyright 2008 Maxime Bizon <mbizon at freebox.fr>
> + * Copyright 2013 Florian Fainelli <florian at openwrt.org>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <clk.h>
> +#include <dm.h>
> +#include <generic-phy.h>
> +#include <power-domain.h>
> +#include <reset.h>
> +#include <asm/io.h>
> +#include <dm/device.h>
> +
> +/* USBH PLL Control register */
> +#define USBH_PLL_REG 0x18
> +#define USBH_PLL_IDDQ_PWRDN BIT(9)
> +#define USBH_PLL_PWRDN_DELAY BIT(10)
> +
> +/* USBH Swap Control register */
> +#define USBH_SWAP_REG 0x1c
> +#define USBH_SWAP_OHCI_DATA BIT(0)
> +#define USBH_SWAP_OHCI_ENDIAN BIT(1)
> +#define USBH_SWAP_EHCI_DATA BIT(3)
> +#define USBH_SWAP_EHCI_ENDIAN BIT(4)
> +
> +/* USBH Setup register */
> +#define USBH_SETUP_REG 0x28
> +#define USBH_SETUP_IOC BIT(4)
> +#define USBH_SETUP_IPP BIT(5)
> +
> +struct bcm6368_usbh_hw {
> + uint32_t setup_clr;
> + uint32_t setup_set;
> + uint32_t pll_clr;
> +};
> +
> +struct bcm6368_usbh_priv {
> + const struct bcm6368_usbh_hw *hw;
> + void __iomem *regs;
> +};
> +
> +static int bcm6368_usbh_init(struct phy *phy)
> +{
> + struct bcm6368_usbh_priv *priv = dev_get_priv(phy->dev);
> + const struct bcm6368_usbh_hw *hw = priv->hw;
> +
> + /* configure to work in native cpu endian */
> + clrsetbits_be32(priv->regs + USBH_SWAP_REG,
> + USBH_SWAP_EHCI_ENDIAN | USBH_SWAP_OHCI_ENDIAN,
> + USBH_SWAP_EHCI_DATA | USBH_SWAP_OHCI_DATA);
> +
> + /* setup config */
> + if (hw->setup_clr)
> + clrbits_be32(priv->regs + USBH_SETUP_REG,
> + hw->setup_clr);
> +
> + setbits_be32(priv->regs + USBH_SETUP_REG, hw->setup_set);
> +
> + /* enable pll control */
> + if (hw->pll_clr)
> + clrbits_be32(priv->regs + USBH_PLL_REG,
> + hw->pll_clr);
> +
> + return 0;
> +}
> +
> +static struct phy_ops bcm6368_usbh_ops = {
> + .init = bcm6368_usbh_init,
> +};
> +
> +static const struct bcm6368_usbh_hw bcm6328_hw = {
> + .pll_clr = USBH_PLL_IDDQ_PWRDN | USBH_PLL_PWRDN_DELAY,
> + .setup_clr = 0,
> + .setup_set = USBH_SETUP_IOC,
> +};
> +
> +static const struct bcm6368_usbh_hw bcm6362_hw = {
> + .pll_clr = 0,
> + .setup_clr = 0,
> + .setup_set = USBH_SETUP_IOC,
> +};
> +
> +static const struct bcm6368_usbh_hw bcm6368_hw = {
> + .pll_clr = 0,
> + .setup_clr = 0,
> + .setup_set = USBH_SETUP_IOC,
> +};
> +
> +static const struct bcm6368_usbh_hw bcm63268_hw = {
> + .pll_clr = USBH_PLL_IDDQ_PWRDN | USBH_PLL_PWRDN_DELAY,
> + .setup_clr = USBH_SETUP_IPP,
> + .setup_set = USBH_SETUP_IOC,
> +};
> +
> +static const struct udevice_id bcm6368_usbh_ids[] = {
> + {
> + .compatible = "brcm,bcm6328-usbh",
> + .data = (ulong)&bcm6328_hw,
> + }, {
> + .compatible = "brcm,bcm6362-usbh",
> + .data = (ulong)&bcm6362_hw,
> + }, {
> + .compatible = "brcm,bcm6368-usbh",
> + .data = (ulong)&bcm6368_hw,
> + }, {
> + .compatible = "brcm,bcm63268-usbh",
> + .data = (ulong)&bcm63268_hw,
> + }, { /* sentinel */ }
> +};
> +
> +static int bcm6368_usbh_probe(struct udevice *dev)
> +{
> + struct bcm6368_usbh_priv *priv = dev_get_priv(dev);
> + const struct bcm6368_usbh_hw *hw =
> + (const struct bcm6368_usbh_hw *)dev_get_driver_data(dev);
> +#if defined(CONFIG_POWER_DOMAIN)
> + struct power_domain pwr_dom;
> +#endif
would the driver work without CONFIG_POWER_DOMAIN or would this be
always needed? I'm asking because in the USB PHY driver for BCM6318 you
do a "select POWER_DOMAIN".
> + struct reset_ctl rst_ctl;
> + struct clk clk;
> + fdt_addr_t addr;
> + fdt_size_t size;
> + int ret;
> +
> + addr = devfdt_get_addr_size_index(dev, 0, &size);
> + if (addr == FDT_ADDR_T_NONE)
> + return -EINVAL;
> +
> + priv->regs = ioremap(addr, size);
> + priv->hw = hw;
> +
> + /* enable usbh clock */
> + ret = clk_get_by_name(dev, "usbh", &clk);
> + if (ret < 0)
> + return ret;
> +
> + ret = clk_enable(&clk);
> + if (ret < 0)
> + return ret;
> +
> + ret = clk_free(&clk);
> + if (ret < 0)
> + return ret;
> +
> +#if defined(CONFIG_POWER_DOMAIN)
> + /* enable power domain */
> + ret = power_domain_get(dev, &pwr_dom);
> + if (ret < 0)
> + return ret;
> +
> + ret = power_domain_on(&pwr_dom);
> + if (ret < 0)
> + return ret;
> +
> + ret = power_domain_free(&pwr_dom);
> + if (ret < 0)
> + return ret;
> +#endif
> +
> + /* perform reset */
> + ret = reset_get_by_index(dev, 0, &rst_ctl);
> + if (ret < 0)
> + return ret;
> +
> + ret = reset_deassert(&rst_ctl);
> + if (ret < 0)
> + return ret;
> +
> + ret = reset_free(&rst_ctl);
> + if (ret < 0)
> + return ret;
> +
> + /* enable usb_ref clock */
> + ret = clk_get_by_name(dev, "usb_ref", &clk);
> + if (!ret) {
> + ret = clk_enable(&clk);
> + if (ret < 0)
> + return ret;
> +
> + ret = clk_free(&clk);
> + if (ret < 0)
> + return ret;
> + }
> +
> + mdelay(100);
> +
> + return 0;
> +}
> +
> +U_BOOT_DRIVER(bcm6368_usbh) = {
> + .name = "bcm6368-usbh",
> + .id = UCLASS_PHY,
> + .of_match = bcm6368_usbh_ids,
> + .ops = &bcm6368_usbh_ops,
> + .priv_auto_alloc_size = sizeof(struct bcm6368_usbh_priv),
> + .probe = bcm6368_usbh_probe,
> +};
>
--
- Daniel
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180204/f6687457/attachment.sig>
More information about the U-Boot
mailing list