[PATCH v3 2/4] arm: Remove d2net_v2 board
Jagan Teki
jagan at amarulasolutions.com
Thu Jun 18 19:45:14 CEST 2020
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Simon Guinot <simon.guinot at sequanux.org>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
Changes for v3:
- new patch
arch/arm/mach-kirkwood/Kconfig | 4 -
board/LaCie/net2big_v2/Kconfig | 12 --
board/LaCie/net2big_v2/MAINTAINERS | 7 -
board/LaCie/net2big_v2/Makefile | 13 --
board/LaCie/net2big_v2/kwbimage.cfg | 149 ----------------
board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------------
board/LaCie/net2big_v2/net2big_v2.h | 28 ---
configs/d2net_v2_defconfig | 53 ------
configs/net2big_v2_defconfig | 53 ------
include/configs/lacie_kw.h | 152 ----------------
10 files changed, 728 deletions(-)
delete mode 100644 board/LaCie/net2big_v2/Kconfig
delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
delete mode 100644 board/LaCie/net2big_v2/Makefile
delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
delete mode 100644 configs/d2net_v2_defconfig
delete mode 100644 configs/net2big_v2_defconfig
delete mode 100644 include/configs/lacie_kw.h
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index ae44cb665e..ad6aef45bf 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD
bool "KM Kirkwood Board"
select VENDOR_KM
-config TARGET_NET2BIG_V2
- bool "LaCie 2Big Network v2 NAS Board"
-
config TARGET_NETSPACE_V2
bool "LaCie netspace_v2 Board"
@@ -80,7 +77,6 @@ source "board/cloudengines/pogo_e02/Kconfig"
source "board/d-link/dns325/Kconfig"
source "board/iomega/iconnect/Kconfig"
source "board/keymile/Kconfig"
-source "board/LaCie/net2big_v2/Kconfig"
source "board/LaCie/netspace_v2/Kconfig"
source "board/raidsonic/ib62x0/Kconfig"
source "board/Seagate/dockstar/Kconfig"
diff --git a/board/LaCie/net2big_v2/Kconfig b/board/LaCie/net2big_v2/Kconfig
deleted file mode 100644
index ba460dba45..0000000000
--- a/board/LaCie/net2big_v2/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_NET2BIG_V2
-
-config SYS_BOARD
- default "net2big_v2"
-
-config SYS_VENDOR
- default "LaCie"
-
-config SYS_CONFIG_NAME
- default "lacie_kw"
-
-endif
diff --git a/board/LaCie/net2big_v2/MAINTAINERS b/board/LaCie/net2big_v2/MAINTAINERS
deleted file mode 100644
index 8fec70315f..0000000000
--- a/board/LaCie/net2big_v2/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-NET2BIG_V2 BOARD
-M: Simon Guinot <simon.guinot at sequanux.org>
-S: Maintained
-F: board/LaCie/net2big_v2/
-F: include/configs/lacie_kw.h
-F: configs/d2net_v2_defconfig
-F: configs/net2big_v2_defconfig
diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
deleted file mode 100644
index 3d12b72812..0000000000
--- a/board/LaCie/net2big_v2/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
-
-obj-y := net2big_v2.o ../common/common.o
-ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
-obj-y += ../common/cpld-gpio-bus.o
-endif
diff --git a/board/LaCie/net2big_v2/kwbimage.cfg b/board/LaCie/net2big_v2/kwbimage.cfg
deleted file mode 100644
index 3897a1197a..0000000000
--- a/board/LaCie/net2big_v2/kwbimage.cfg
+++ /dev/null
@@ -1,149 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM spi # Boot from SPI flash
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000C30 # DDR Configuration register
-# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x38743000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000A32 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x0000CCCC # DDR Address Control
-# bit1-0: 01, Cs0width=x16
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs2width=nonexistent
-# bit7-6: 00, Cs1size =nonexistent
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000662 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000044 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strenght reduced
-# bit2: 1, DDR ODT control lsd enabled
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, enabled
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 1 , D2P Latency enabled
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x07, Size (i.e. 128MB)
-
-DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
-# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
-# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
-
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
-# bit3-2: 01, ODT1 active NEVER!
-# bit31-4: zero, required
-
-DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
-# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
-# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
-# bit11-10:1, DQ_ODTSel. ODT select turned on
-
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
deleted file mode 100644
index dbd8b5755d..0000000000
--- a/board/LaCie/net2big_v2/net2big_v2.c
+++ /dev/null
@@ -1,257 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <i2c.h>
-#include <init.h>
-#include <net.h>
-#include <asm/mach-types.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
-
-#include "net2big_v2.h"
-#include "../common/common.h"
-#include "../common/cpld-gpio-bus.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- /* GPIO configuration */
- mvebu_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH,
- NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- static const u32 kwmpp_config[] = {
- MPP0_SPI_SCn,
- MPP1_SPI_MOSI,
- MPP2_SPI_SCK,
- MPP3_SPI_MISO,
- MPP6_SYSRST_OUTn,
- MPP7_GPO, /* Request power-off */
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP13_GPIO, /* Rear power switch (on|auto) */
- MPP14_GPIO, /* USB fuse alarm */
- MPP15_GPIO, /* Rear power switch (auto|off) */
- MPP16_GPIO, /* SATA HDD1 power */
- MPP17_GPIO, /* SATA HDD2 power */
- MPP20_SATA1_ACTn,
- MPP21_SATA0_ACTn,
- MPP24_GPIO, /* USB mode select */
- MPP26_GPIO, /* USB device vbus */
- MPP28_GPIO, /* USB enable host vbus */
- MPP29_GPIO, /* CPLD GPIO bus ALE */
- MPP34_GPIO, /* Rear Push button 0=on 1=off */
- MPP35_GPIO, /* Inhibit switch power-off */
- MPP36_GPIO, /* SATA HDD1 presence */
- MPP37_GPIO, /* SATA HDD2 presence */
- MPP40_GPIO, /* eSATA presence */
- MPP44_GPIO, /* CPLD GPIO bus (data 0) */
- MPP45_GPIO, /* CPLD GPIO bus (data 1) */
- MPP46_GPIO, /* CPLD GPIO bus (data 2) */
- MPP47_GPIO, /* CPLD GPIO bus (addr 0) */
- MPP48_GPIO, /* CPLD GPIO bus (addr 1) */
- MPP49_GPIO, /* CPLD GPIO bus (addr 2) */
- 0
- };
-
- kirkwood_mpp_conf(kwmpp_config, NULL);
-
- return 0;
-}
-
-int board_init(void)
-{
- /* Machine number */
- gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2;
-
- /* Boot parameters address */
- gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
- return 0;
-}
-
-#if defined(CONFIG_MISC_INIT_R)
-
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR)
-/*
- * Start I2C fan (GMT G762 controller)
- */
-static void init_fan(void)
-{
- u8 data;
-
- i2c_set_bus_num(0);
-
- /* Enable open-loop and PWM modes */
- data = 0x20;
- if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
- G762_REG_FAN_CMD1, 1, &data, 1) != 0)
- goto err;
- data = 0;
- if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
- G762_REG_SET_CNT, 1, &data, 1) != 0)
- goto err;
- /*
- * RPM to PWM (set_out register) fan speed conversion array:
- * 0 0x00
- * 1500 0x04
- * 2800 0x08
- * 3400 0x0C
- * 3700 0x10
- * 4400 0x20
- * 4700 0x30
- * 4800 0x50
- * 5200 0x80
- * 5400 0xC0
- * 5500 0xFF
- *
- * Start fan at low speed (2800 RPM):
- */
- data = 0x08;
- if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
- G762_REG_SET_OUT, 1, &data, 1) != 0)
- goto err;
-
- return;
-err:
- printf("Error: failed to start I2C fan @%02x\n",
- CONFIG_SYS_I2C_G762_ADDR);
-}
-#else
-static void init_fan(void) {}
-#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
-
-#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
-/*
- * CPLD GPIO bus:
- *
- * - address register : bit [0-2] -> GPIO [47-49]
- * - data register : bit [0-2] -> GPIO [44-46]
- * - enable register : GPIO 29
- */
-static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
-static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
-
-static struct cpld_gpio_bus cpld_gpio_bus = {
- .addr = cpld_gpio_bus_addr,
- .num_addr = ARRAY_SIZE(cpld_gpio_bus_addr),
- .data = cpld_gpio_bus_data,
- .num_data = ARRAY_SIZE(cpld_gpio_bus_data),
- .enable = 29,
-};
-
-/*
- * LEDs configuration:
- *
- * The LEDs are controlled by a CPLD and can be configured through
- * the CPLD GPIO bus.
- *
- * Address register selection:
- *
- * addr | register
- * ----------------------------
- * 0 | front LED
- * 1 | front LED brightness
- * 2 | SATA LED brightness
- * 3 | SATA0 LED
- * 4 | SATA1 LED
- * 5 | SATA2 LED
- * 6 | SATA3 LED
- * 7 | SATA4 LED
- *
- * Data register configuration:
- *
- * data | LED brightness
- * -------------------------------------------------
- * 0 | min (off)
- * - | -
- * 7 | max
- *
- * data | front LED mode
- * -------------------------------------------------
- * 0 | fix off
- * 1 | fix blue on
- * 2 | fix red on
- * 3 | blink blue on=1 sec and blue off=1 sec
- * 4 | blink red on=1 sec and red off=1 sec
- * 5 | blink blue on=2.5 sec and red on=0.5 sec
- * 6 | blink blue on=1 sec and red on=1 sec
- * 7 | blink blue on=0.5 sec and blue off=2.5 sec
- *
- * data | SATA LED mode
- * -------------------------------------------------
- * 0 | fix off
- * 1 | SATA activity blink
- * 2 | fix red on
- * 3 | blink blue on=1 sec and blue off=1 sec
- * 4 | blink red on=1 sec and red off=1 sec
- * 5 | blink blue on=2.5 sec and red on=0.5 sec
- * 6 | blink blue on=1 sec and red on=1 sec
- * 7 | fix blue on
- */
-static void init_leds(void)
-{
- /* Enable the front blue LED */
- cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
- cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
-
- /* Configure SATA LEDs to blink in relation with the SATA activity */
- cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
- cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
- cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
-}
-#else
-static void init_leds(void) {}
-#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
-
-int misc_init_r(void)
-{
- init_fan();
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
- if (!env_get("ethaddr")) {
- uchar mac[6];
- if (lacie_read_mac_address(mac) == 0)
- eth_env_set_enetaddr("ethaddr", mac);
- }
-#endif
- init_leds();
-
- return 0;
-}
-#endif /* CONFIG_MISC_INIT_R */
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
-/* Configure and initialize PHY */
-void reset_phy(void)
-{
- mv_phy_88e1116_init("egiga0", 8);
-}
-#endif
-
-#if defined(CONFIG_KIRKWOOD_GPIO)
-/* Return GPIO push button status */
-static int
-do_read_push_button(struct cmd_tbl *cmdtp, int flag, int argc,
- char *const argv[])
-{
- return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON);
-}
-
-U_BOOT_CMD(button, 1, 1, do_read_push_button,
- "Return GPIO push button status 0=off 1=on", "");
-#endif
diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
deleted file mode 100644
index d61dd0e998..0000000000
--- a/board/LaCie/net2big_v2/net2big_v2.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
- */
-
-#ifndef NET2BIG_V2_H
-#define NET2BIG_V2_H
-
-/* GPIO configuration */
-#define NET2BIG_V2_OE_LOW 0x0600E000
-#define NET2BIG_V2_OE_HIGH 0x00000134
-#define NET2BIG_V2_OE_VAL_LOW 0x10030000
-#define NET2BIG_V2_OE_VAL_HIGH 0x00000000
-
-/* Buttons */
-#define NET2BIG_V2_GPIO_PUSH_BUTTON 34
-
-/* GMT G762 registers (I2C fan controller) */
-#define G762_REG_SET_CNT 0x00
-#define G762_REG_SET_OUT 0x03
-#define G762_REG_FAN_CMD1 0x04
-
-#endif /* NET2BIG_V2_H */
diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig
deleted file mode 100644
index fe3c6c4762..0000000000
--- a/configs/d2net_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NET2BIG_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" D2 v2"
-CONFIG_SYS_EXTRA_OPTIONS="D2NET_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="d2v2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig
deleted file mode 100644
index 1389d30900..0000000000
--- a/configs/net2big_v2_defconfig
+++ /dev/null
@@ -1,53 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SYS_DCACHE_OFF=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_KIRKWOOD=y
-CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_TARGET_NET2BIG_V2=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x70000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_IDENT_STRING=" 2Big v2"
-CONFIG_SYS_EXTRA_OPTIONS="NET2BIG_V2"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200"
-CONFIG_USE_PREBOOT=y
-CONFIG_CONSOLE_MUX=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="2big2> "
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
-CONFIG_OF_CONTROL=y
-CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big"
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=20000000
-CONFIG_ENV_ADDR=0x70000
-CONFIG_MVSATA_IDE=y
-# CONFIG_MMC is not set
-CONFIG_SPI_FLASH=y
-CONFIG_SPI_FLASH_MACRONIX=y
-CONFIG_MVGBE=y
-CONFIG_MII=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_KIRKWOOD_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h
deleted file mode 100644
index 5bb0255a74..0000000000
--- a/include/configs/lacie_kw.h
+++ /dev/null
@@ -1,152 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
- */
-
-#ifndef _CONFIG_LACIE_KW_H
-#define _CONFIG_LACIE_KW_H
-
-/*
- * Machine number definition
- */
-#if defined(CONFIG_INETSPACE_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_INETSPACE_V2
-#elif defined(CONFIG_NETSPACE_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_V2
-#elif defined(CONFIG_NETSPACE_LITE_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_LITE_V2
-#elif defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MINI_V2
-#elif defined(CONFIG_NETSPACE_MAX_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MAX_V2
-#elif defined(CONFIG_D2NET_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_D2NET_V2
-#elif defined(CONFIG_NET2BIG_V2)
-#define CONFIG_MACH_TYPE MACH_TYPE_NET2BIG_V2
-#else
-#error "Unknown board"
-#endif
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
-/* SoC name */
-#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_KW88F6192
-#else
-#define CONFIG_KW88F6281
-#endif
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
-/*
- * Core clock definition
- */
-#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
-
-/*
- * SDRAM configuration
- */
-
-/*
- * Different SDRAM configuration and size for some of the boards derived
- * from the Network Space v2
- */
-#if defined(CONFIG_INETSPACE_V2)
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-is2.cfg
-#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
-#endif
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_SYS_IDE_MAXBUS
-#undef CONFIG_SYS_IDE_MAXDEVICE
-
-/*
- * Enable platform initialisation via misc_init_r() function
- */
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-#define CONFIG_NETCONSOLE
-#endif
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
-#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
- defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
-#define CONFIG_SYS_IDE_MAXBUS 2
-#define CONFIG_SYS_IDE_MAXDEVICE 2
-#else
-#define CONFIG_SYS_IDE_MAXBUS 1
-#define CONFIG_SYS_IDE_MAXDEVICE 1
-#endif
-#endif /* CONFIG_MVSATA_IDE */
-
-/*
- * Enable GPI0 support
- */
-#define CONFIG_KIRKWOOD_GPIO
-
-/*
- * Enable I2C support
- */
-#ifdef CONFIG_CMD_I2C
-/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
-#if defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_I2C_G762_ADDR 0x3e
-#endif
-#endif /* CONFIG_CMD_I2C */
-
-/*
- * Partition support
- */
-
-/*
- * File systems support
- */
-
-/*
- * Environment variables configurations
- */
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTCOMMAND \
- "dhcp && run netconsole; " \
- "if run usbload || run diskload; then bootm; fi"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "stdin=serial\0" \
- "stdout=serial\0" \
- "stderr=serial\0" \
- "bootfile=uImage\0" \
- "loadaddr=0x800000\0" \
- "autoload=no\0" \
- "netconsole=" \
- "set stdin $stdin,nc; " \
- "set stdout $stdout,nc; " \
- "set stderr $stderr,nc;\0" \
- "diskload=ide reset && " \
- "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
- "usbload=usb start && " \
- "fatload usb 0:1 $loadaddr /boot/$bootfile\0"
-
-#endif /* _CONFIG_LACIE_KW_H */
--
2.25.1
More information about the U-Boot
mailing list