[PATCH v3 2/4] arm: Remove d2net_v2 board
Simon Guinot
simon.guinot at sequanux.org
Fri Jun 19 00:02:17 CEST 2020
On Thu, Jun 18, 2020 at 11:15:14PM +0530, Jagan Teki wrote:
Hi Jagan,
> This board has not been converted to CONFIG_DM by the deadline.
Is that possible to negociate a new deadline ?
Thanks in advance.
Simon
>
> Remove it.
>
> Cc: Simon Guinot <simon.guinot at sequanux.org>
> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> ---
> Changes for v3:
> - new patch
>
> arch/arm/mach-kirkwood/Kconfig | 4 -
> board/LaCie/net2big_v2/Kconfig | 12 --
> board/LaCie/net2big_v2/MAINTAINERS | 7 -
> board/LaCie/net2big_v2/Makefile | 13 --
> board/LaCie/net2big_v2/kwbimage.cfg | 149 ----------------
> board/LaCie/net2big_v2/net2big_v2.c | 257 ----------------------------
> board/LaCie/net2big_v2/net2big_v2.h | 28 ---
> configs/d2net_v2_defconfig | 53 ------
> configs/net2big_v2_defconfig | 53 ------
> include/configs/lacie_kw.h | 152 ----------------
> 10 files changed, 728 deletions(-)
> delete mode 100644 board/LaCie/net2big_v2/Kconfig
> delete mode 100644 board/LaCie/net2big_v2/MAINTAINERS
> delete mode 100644 board/LaCie/net2big_v2/Makefile
> delete mode 100644 board/LaCie/net2big_v2/kwbimage.cfg
> delete mode 100644 board/LaCie/net2big_v2/net2big_v2.c
> delete mode 100644 board/LaCie/net2big_v2/net2big_v2.h
> delete mode 100644 configs/d2net_v2_defconfig
> delete mode 100644 configs/net2big_v2_defconfig
> delete mode 100644 include/configs/lacie_kw.h
>
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index ae44cb665e..ad6aef45bf 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -35,9 +35,6 @@ config TARGET_KM_KIRKWOOD
> bool "KM Kirkwood Board"
> select VENDOR_KM
>
> -config TARGET_NET2BIG_V2
> - bool "LaCie 2Big Network v2 NAS Board"
> -
> config TARGET_NETSPACE_V2
> bool "LaCie netspace_v2 Board"
>
> @@ -80,7 +77,6 @@ source "board/cloudengines/pogo_e02/Kconfig"
> source "board/d-link/dns325/Kconfig"
> source "board/iomega/iconnect/Kconfig"
> source "board/keymile/Kconfig"
> -source "board/LaCie/net2big_v2/Kconfig"
> source "board/LaCie/netspace_v2/Kconfig"
> source "board/raidsonic/ib62x0/Kconfig"
> source "board/Seagate/dockstar/Kconfig"
> diff --git a/board/LaCie/net2big_v2/Kconfig b/board/LaCie/net2big_v2/Kconfig
> deleted file mode 100644
> index ba460dba45..0000000000
> --- a/board/LaCie/net2big_v2/Kconfig
> +++ /dev/null
> @@ -1,12 +0,0 @@
> -if TARGET_NET2BIG_V2
> -
> -config SYS_BOARD
> - default "net2big_v2"
> -
> -config SYS_VENDOR
> - default "LaCie"
> -
> -config SYS_CONFIG_NAME
> - default "lacie_kw"
> -
> -endif
> diff --git a/board/LaCie/net2big_v2/MAINTAINERS b/board/LaCie/net2big_v2/MAINTAINERS
> deleted file mode 100644
> index 8fec70315f..0000000000
> --- a/board/LaCie/net2big_v2/MAINTAINERS
> +++ /dev/null
> @@ -1,7 +0,0 @@
> -NET2BIG_V2 BOARD
> -M: Simon Guinot <simon.guinot at sequanux.org>
> -S: Maintained
> -F: board/LaCie/net2big_v2/
> -F: include/configs/lacie_kw.h
> -F: configs/d2net_v2_defconfig
> -F: configs/net2big_v2_defconfig
> diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile
> deleted file mode 100644
> index 3d12b72812..0000000000
> --- a/board/LaCie/net2big_v2/Makefile
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> -
> -obj-y := net2big_v2.o ../common/common.o
> -ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),)
> -obj-y += ../common/cpld-gpio-bus.o
> -endif
> diff --git a/board/LaCie/net2big_v2/kwbimage.cfg b/board/LaCie/net2big_v2/kwbimage.cfg
> deleted file mode 100644
> index 3897a1197a..0000000000
> --- a/board/LaCie/net2big_v2/kwbimage.cfg
> +++ /dev/null
> @@ -1,149 +0,0 @@
> -# SPDX-License-Identifier: GPL-2.0+
> -#
> -# Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> -#
> -# Based on Kirkwood support:
> -# (C) Copyright 2009
> -# Marvell Semiconductor <www.marvell.com>
> -# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> -# Refer doc/README.kwbimage for more details about how-to configure
> -# and create kirkwood boot image
> -#
> -
> -# Boot Media configurations
> -BOOT_FROM spi # Boot from SPI flash
> -
> -# SOC registers configuration using bootrom header extension
> -# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> -
> -# Configure RGMII-0 interface pad voltage to 1.8V
> -DATA 0xFFD100e0 0x1B1B1B9B
> -
> -#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> -DATA 0xFFD01400 0x43000C30 # DDR Configuration register
> -# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
> -# bit23-14: zero
> -# bit24: 1= enable exit self refresh mode on DDR access
> -# bit25: 1 required
> -# bit29-26: zero
> -# bit31-30: 01
> -
> -DATA 0xFFD01404 0x38743000 # DDR Controller Control Low
> -# bit 4: 0=addr/cmd in smame cycle
> -# bit 5: 0=clk is driven during self refresh, we don't care for APX
> -# bit 6: 0=use recommended falling edge of clk for addr/cmd
> -# bit14: 0=input buffer always powered up
> -# bit18: 1=cpu lock transaction enabled
> -# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
> -# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
> -# bit30-28: 3 required
> -# bit31: 0=no additional STARTBURST delay
> -
> -DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
> -# bit7-4: TRCD
> -# bit11- 8: TRP
> -# bit15-12: TWR
> -# bit19-16: TWTR
> -# bit20: TRAS msb
> -# bit23-21: 0x0
> -# bit27-24: TRRD
> -# bit31-28: TRTP
> -
> -DATA 0xFFD0140C 0x00000A32 # DDR Timing (High)
> -# bit6-0: TRFC
> -# bit8-7: TR2R
> -# bit10-9: TR2W
> -# bit12-11: TW2W
> -# bit31-13: zero required
> -
> -DATA 0xFFD01410 0x0000CCCC # DDR Address Control
> -# bit1-0: 01, Cs0width=x16
> -# bit3-2: 11, Cs0size=1Gb
> -# bit5-4: 00, Cs2width=nonexistent
> -# bit7-6: 00, Cs1size =nonexistent
> -# bit9-8: 00, Cs2width=nonexistent
> -# bit11-10: 00, Cs2size =nonexistent
> -# bit13-12: 00, Cs3width=nonexistent
> -# bit15-14: 00, Cs3size =nonexistent
> -# bit16: 0, Cs0AddrSel
> -# bit17: 0, Cs1AddrSel
> -# bit18: 0, Cs2AddrSel
> -# bit19: 0, Cs3AddrSel
> -# bit31-20: 0 required
> -
> -DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
> -# bit0: 0, OpenPage enabled
> -# bit31-1: 0 required
> -
> -DATA 0xFFD01418 0x00000000 # DDR Operation
> -# bit3-0: 0x0, DDR cmd
> -# bit31-4: 0 required
> -
> -DATA 0xFFD0141C 0x00000662 # DDR Mode
> -# bit2-0: 2, BurstLen=2 required
> -# bit3: 0, BurstType=0 required
> -# bit6-4: 4, CL=5
> -# bit7: 0, TestMode=0 normal
> -# bit8: 0, DLL reset=0 normal
> -# bit11-9: 6, auto-precharge write recovery ????????????
> -# bit12: 0, PD must be zero
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01420 0x00000044 # DDR Extended Mode
> -# bit0: 0, DDR DLL enabled
> -# bit1: 1, DDR drive strenght reduced
> -# bit2: 1, DDR ODT control lsd enabled
> -# bit5-3: 000, required
> -# bit6: 1, DDR ODT control msb, enabled
> -# bit9-7: 000, required
> -# bit10: 0, differential DQS enabled
> -# bit11: 0, required
> -# bit12: 0, DDR output buffer enabled
> -# bit31-13: 0 required
> -
> -DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
> -# bit2-0: 111, required
> -# bit3 : 1 , MBUS Burst Chop disabled
> -# bit6-4: 111, required
> -# bit7 : 1 , D2P Latency enabled
> -# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
> -# bit9 : 0 , no half clock cycle addition to dataout
> -# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
> -# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
> -# bit15-12: 1111 required
> -# bit31-16: 0 required
> -
> -DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values)
> -DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values)
> -
> -DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
> -DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
> -# bit0: 1, Window enabled
> -# bit1: 0, Write Protect disabled
> -# bit3-2: 00, CS0 hit selected
> -# bit23-4: ones, required
> -# bit31-24: 0x07, Size (i.e. 128MB)
> -
> -DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
> -DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
> -DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
> -
> -DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
> -# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
> -# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> -
> -DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
> -# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
> -# bit3-2: 01, ODT1 active NEVER!
> -# bit31-4: zero, required
> -
> -DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
> -# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
> -# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
> -# bit11-10:1, DQ_ODTSel. ODT select turned on
> -
> -DATA 0xFFD01480 0x00000001 # DDR Initialization Control
> -#bit0=1, enable DDR init upon this register write
> -
> -# End of Header extension
> -DATA 0x0 0x0
> diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c
> deleted file mode 100644
> index dbd8b5755d..0000000000
> --- a/board/LaCie/net2big_v2/net2big_v2.c
> +++ /dev/null
> @@ -1,257 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0+
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> - */
> -
> -#include <common.h>
> -#include <command.h>
> -#include <env.h>
> -#include <i2c.h>
> -#include <init.h>
> -#include <net.h>
> -#include <asm/mach-types.h>
> -#include <asm/arch/cpu.h>
> -#include <asm/arch/soc.h>
> -#include <asm/arch/mpp.h>
> -#include <asm/arch/gpio.h>
> -
> -#include "net2big_v2.h"
> -#include "../common/common.h"
> -#include "../common/cpld-gpio-bus.h"
> -
> -DECLARE_GLOBAL_DATA_PTR;
> -
> -int board_early_init_f(void)
> -{
> - /* GPIO configuration */
> - mvebu_config_gpio(NET2BIG_V2_OE_VAL_LOW, NET2BIG_V2_OE_VAL_HIGH,
> - NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
> -
> - /* Multi-Purpose Pins Functionality configuration */
> - static const u32 kwmpp_config[] = {
> - MPP0_SPI_SCn,
> - MPP1_SPI_MOSI,
> - MPP2_SPI_SCK,
> - MPP3_SPI_MISO,
> - MPP6_SYSRST_OUTn,
> - MPP7_GPO, /* Request power-off */
> - MPP8_TW_SDA,
> - MPP9_TW_SCK,
> - MPP10_UART0_TXD,
> - MPP11_UART0_RXD,
> - MPP13_GPIO, /* Rear power switch (on|auto) */
> - MPP14_GPIO, /* USB fuse alarm */
> - MPP15_GPIO, /* Rear power switch (auto|off) */
> - MPP16_GPIO, /* SATA HDD1 power */
> - MPP17_GPIO, /* SATA HDD2 power */
> - MPP20_SATA1_ACTn,
> - MPP21_SATA0_ACTn,
> - MPP24_GPIO, /* USB mode select */
> - MPP26_GPIO, /* USB device vbus */
> - MPP28_GPIO, /* USB enable host vbus */
> - MPP29_GPIO, /* CPLD GPIO bus ALE */
> - MPP34_GPIO, /* Rear Push button 0=on 1=off */
> - MPP35_GPIO, /* Inhibit switch power-off */
> - MPP36_GPIO, /* SATA HDD1 presence */
> - MPP37_GPIO, /* SATA HDD2 presence */
> - MPP40_GPIO, /* eSATA presence */
> - MPP44_GPIO, /* CPLD GPIO bus (data 0) */
> - MPP45_GPIO, /* CPLD GPIO bus (data 1) */
> - MPP46_GPIO, /* CPLD GPIO bus (data 2) */
> - MPP47_GPIO, /* CPLD GPIO bus (addr 0) */
> - MPP48_GPIO, /* CPLD GPIO bus (addr 1) */
> - MPP49_GPIO, /* CPLD GPIO bus (addr 2) */
> - 0
> - };
> -
> - kirkwood_mpp_conf(kwmpp_config, NULL);
> -
> - return 0;
> -}
> -
> -int board_init(void)
> -{
> - /* Machine number */
> - gd->bd->bi_arch_number = MACH_TYPE_NET2BIG_V2;
> -
> - /* Boot parameters address */
> - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
> -
> - return 0;
> -}
> -
> -#if defined(CONFIG_MISC_INIT_R)
> -
> -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR)
> -/*
> - * Start I2C fan (GMT G762 controller)
> - */
> -static void init_fan(void)
> -{
> - u8 data;
> -
> - i2c_set_bus_num(0);
> -
> - /* Enable open-loop and PWM modes */
> - data = 0x20;
> - if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> - G762_REG_FAN_CMD1, 1, &data, 1) != 0)
> - goto err;
> - data = 0;
> - if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> - G762_REG_SET_CNT, 1, &data, 1) != 0)
> - goto err;
> - /*
> - * RPM to PWM (set_out register) fan speed conversion array:
> - * 0 0x00
> - * 1500 0x04
> - * 2800 0x08
> - * 3400 0x0C
> - * 3700 0x10
> - * 4400 0x20
> - * 4700 0x30
> - * 4800 0x50
> - * 5200 0x80
> - * 5400 0xC0
> - * 5500 0xFF
> - *
> - * Start fan at low speed (2800 RPM):
> - */
> - data = 0x08;
> - if (i2c_write(CONFIG_SYS_I2C_G762_ADDR,
> - G762_REG_SET_OUT, 1, &data, 1) != 0)
> - goto err;
> -
> - return;
> -err:
> - printf("Error: failed to start I2C fan @%02x\n",
> - CONFIG_SYS_I2C_G762_ADDR);
> -}
> -#else
> -static void init_fan(void) {}
> -#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */
> -
> -#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO)
> -/*
> - * CPLD GPIO bus:
> - *
> - * - address register : bit [0-2] -> GPIO [47-49]
> - * - data register : bit [0-2] -> GPIO [44-46]
> - * - enable register : GPIO 29
> - */
> -static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 };
> -static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 };
> -
> -static struct cpld_gpio_bus cpld_gpio_bus = {
> - .addr = cpld_gpio_bus_addr,
> - .num_addr = ARRAY_SIZE(cpld_gpio_bus_addr),
> - .data = cpld_gpio_bus_data,
> - .num_data = ARRAY_SIZE(cpld_gpio_bus_data),
> - .enable = 29,
> -};
> -
> -/*
> - * LEDs configuration:
> - *
> - * The LEDs are controlled by a CPLD and can be configured through
> - * the CPLD GPIO bus.
> - *
> - * Address register selection:
> - *
> - * addr | register
> - * ----------------------------
> - * 0 | front LED
> - * 1 | front LED brightness
> - * 2 | SATA LED brightness
> - * 3 | SATA0 LED
> - * 4 | SATA1 LED
> - * 5 | SATA2 LED
> - * 6 | SATA3 LED
> - * 7 | SATA4 LED
> - *
> - * Data register configuration:
> - *
> - * data | LED brightness
> - * -------------------------------------------------
> - * 0 | min (off)
> - * - | -
> - * 7 | max
> - *
> - * data | front LED mode
> - * -------------------------------------------------
> - * 0 | fix off
> - * 1 | fix blue on
> - * 2 | fix red on
> - * 3 | blink blue on=1 sec and blue off=1 sec
> - * 4 | blink red on=1 sec and red off=1 sec
> - * 5 | blink blue on=2.5 sec and red on=0.5 sec
> - * 6 | blink blue on=1 sec and red on=1 sec
> - * 7 | blink blue on=0.5 sec and blue off=2.5 sec
> - *
> - * data | SATA LED mode
> - * -------------------------------------------------
> - * 0 | fix off
> - * 1 | SATA activity blink
> - * 2 | fix red on
> - * 3 | blink blue on=1 sec and blue off=1 sec
> - * 4 | blink red on=1 sec and red off=1 sec
> - * 5 | blink blue on=2.5 sec and red on=0.5 sec
> - * 6 | blink blue on=1 sec and red on=1 sec
> - * 7 | fix blue on
> - */
> -static void init_leds(void)
> -{
> - /* Enable the front blue LED */
> - cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1);
> - cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3);
> -
> - /* Configure SATA LEDs to blink in relation with the SATA activity */
> - cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1);
> - cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1);
> - cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3);
> -}
> -#else
> -static void init_leds(void) {}
> -#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */
> -
> -int misc_init_r(void)
> -{
> - init_fan();
> -#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
> - if (!env_get("ethaddr")) {
> - uchar mac[6];
> - if (lacie_read_mac_address(mac) == 0)
> - eth_env_set_enetaddr("ethaddr", mac);
> - }
> -#endif
> - init_leds();
> -
> - return 0;
> -}
> -#endif /* CONFIG_MISC_INIT_R */
> -
> -#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
> -/* Configure and initialize PHY */
> -void reset_phy(void)
> -{
> - mv_phy_88e1116_init("egiga0", 8);
> -}
> -#endif
> -
> -#if defined(CONFIG_KIRKWOOD_GPIO)
> -/* Return GPIO push button status */
> -static int
> -do_read_push_button(struct cmd_tbl *cmdtp, int flag, int argc,
> - char *const argv[])
> -{
> - return !kw_gpio_get_value(NET2BIG_V2_GPIO_PUSH_BUTTON);
> -}
> -
> -U_BOOT_CMD(button, 1, 1, do_read_push_button,
> - "Return GPIO push button status 0=off 1=on", "");
> -#endif
> diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h
> deleted file mode 100644
> index d61dd0e998..0000000000
> --- a/board/LaCie/net2big_v2/net2big_v2.h
> +++ /dev/null
> @@ -1,28 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> - *
> - * Based on Kirkwood support:
> - * (C) Copyright 2009
> - * Marvell Semiconductor <www.marvell.com>
> - * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> - */
> -
> -#ifndef NET2BIG_V2_H
> -#define NET2BIG_V2_H
> -
> -/* GPIO configuration */
> -#define NET2BIG_V2_OE_LOW 0x0600E000
> -#define NET2BIG_V2_OE_HIGH 0x00000134
> -#define NET2BIG_V2_OE_VAL_LOW 0x10030000
> -#define NET2BIG_V2_OE_VAL_HIGH 0x00000000
> -
> -/* Buttons */
> -#define NET2BIG_V2_GPIO_PUSH_BUTTON 34
> -
> -/* GMT G762 registers (I2C fan controller) */
> -#define G762_REG_SET_CNT 0x00
> -#define G762_REG_SET_OUT 0x03
> -#define G762_REG_FAN_CMD1 0x04
> -
> -#endif /* NET2BIG_V2_H */
> diff --git a/configs/d2net_v2_defconfig b/configs/d2net_v2_defconfig
> deleted file mode 100644
> index fe3c6c4762..0000000000
> --- a/configs/d2net_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NET2BIG_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" D2 v2"
> -CONFIG_SYS_EXTRA_OPTIONS="D2NET_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="d2v2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-d2net"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/configs/net2big_v2_defconfig b/configs/net2big_v2_defconfig
> deleted file mode 100644
> index 1389d30900..0000000000
> --- a/configs/net2big_v2_defconfig
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -CONFIG_ARM=y
> -CONFIG_SYS_DCACHE_OFF=y
> -CONFIG_ARCH_CPU_INIT=y
> -CONFIG_ARCH_KIRKWOOD=y
> -CONFIG_SYS_TEXT_BASE=0x600000
> -CONFIG_TARGET_NET2BIG_V2=y
> -CONFIG_ENV_SIZE=0x1000
> -CONFIG_ENV_OFFSET=0x70000
> -CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_NR_DRAM_BANKS=2
> -CONFIG_IDENT_STRING=" 2Big v2"
> -CONFIG_SYS_EXTRA_OPTIONS="NET2BIG_V2"
> -CONFIG_BOOTDELAY=3
> -CONFIG_USE_BOOTARGS=y
> -CONFIG_BOOTARGS="console=ttyS0,115200"
> -CONFIG_USE_PREBOOT=y
> -CONFIG_CONSOLE_MUX=y
> -CONFIG_MISC_INIT_R=y
> -# CONFIG_DISPLAY_BOARDINFO is not set
> -CONFIG_HUSH_PARSER=y
> -CONFIG_SYS_PROMPT="2big2> "
> -CONFIG_CMD_EEPROM=y
> -CONFIG_CMD_IDE=y
> -CONFIG_CMD_I2C=y
> -CONFIG_CMD_SF=y
> -CONFIG_CMD_USB=y
> -# CONFIG_CMD_SETEXPR is not set
> -CONFIG_CMD_DHCP=y
> -CONFIG_CMD_MII=y
> -CONFIG_CMD_PING=y
> -CONFIG_CMD_EXT2=y
> -CONFIG_CMD_FAT=y
> -CONFIG_ISO_PARTITION=y
> -CONFIG_EFI_PARTITION=y
> -# CONFIG_PARTITION_UUIDS is not set
> -CONFIG_OF_CONTROL=y
> -CONFIG_DEFAULT_DEVICE_TREE="kirkwood-net2big"
> -CONFIG_ENV_IS_IN_SPI_FLASH=y
> -CONFIG_USE_ENV_SPI_MAX_HZ=y
> -CONFIG_ENV_SPI_MAX_HZ=20000000
> -CONFIG_ENV_ADDR=0x70000
> -CONFIG_MVSATA_IDE=y
> -# CONFIG_MMC is not set
> -CONFIG_SPI_FLASH=y
> -CONFIG_SPI_FLASH_MACRONIX=y
> -CONFIG_MVGBE=y
> -CONFIG_MII=y
> -CONFIG_SYS_NS16550=y
> -CONFIG_SPI=y
> -CONFIG_KIRKWOOD_SPI=y
> -CONFIG_USB=y
> -CONFIG_USB_EHCI_HCD=y
> -CONFIG_USB_STORAGE=y
> diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h
> deleted file mode 100644
> index 5bb0255a74..0000000000
> --- a/include/configs/lacie_kw.h
> +++ /dev/null
> @@ -1,152 +0,0 @@
> -/* SPDX-License-Identifier: GPL-2.0+ */
> -/*
> - * Copyright (C) 2011 Simon Guinot <sguinot at lacie.com>
> - */
> -
> -#ifndef _CONFIG_LACIE_KW_H
> -#define _CONFIG_LACIE_KW_H
> -
> -/*
> - * Machine number definition
> - */
> -#if defined(CONFIG_INETSPACE_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_INETSPACE_V2
> -#elif defined(CONFIG_NETSPACE_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_V2
> -#elif defined(CONFIG_NETSPACE_LITE_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_LITE_V2
> -#elif defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MINI_V2
> -#elif defined(CONFIG_NETSPACE_MAX_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NETSPACE_MAX_V2
> -#elif defined(CONFIG_D2NET_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_D2NET_V2
> -#elif defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_MACH_TYPE MACH_TYPE_NET2BIG_V2
> -#else
> -#error "Unknown board"
> -#endif
> -
> -/*
> - * High Level Configuration Options (easy to change)
> - */
> -#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
> -/* SoC name */
> -#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_KW88F6192
> -#else
> -#define CONFIG_KW88F6281
> -#endif
> -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
> -
> -/*
> - * Core clock definition
> - */
> -#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
> -
> -/*
> - * SDRAM configuration
> - */
> -
> -/*
> - * Different SDRAM configuration and size for some of the boards derived
> - * from the Network Space v2
> - */
> -#if defined(CONFIG_INETSPACE_V2)
> -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-is2.cfg
> -#elif defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2)
> -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-ns2l.cfg
> -#endif
> -
> -/*
> - * mv-common.h should be defined after CMD configs since it used them
> - * to enable certain macros
> - */
> -#include "mv-common.h"
> -
> -/* Remove or override few declarations from mv-common.h */
> -#undef CONFIG_SYS_IDE_MAXBUS
> -#undef CONFIG_SYS_IDE_MAXDEVICE
> -
> -/*
> - * Enable platform initialisation via misc_init_r() function
> - */
> -
> -/*
> - * Ethernet Driver configuration
> - */
> -#ifdef CONFIG_CMD_NET
> -#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
> -#define CONFIG_NETCONSOLE
> -#endif
> -
> -/*
> - * SATA Driver configuration
> - */
> -#ifdef CONFIG_MVSATA_IDE
> -#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
> -#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
> - defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
> -#define CONFIG_SYS_IDE_MAXBUS 2
> -#define CONFIG_SYS_IDE_MAXDEVICE 2
> -#else
> -#define CONFIG_SYS_IDE_MAXBUS 1
> -#define CONFIG_SYS_IDE_MAXDEVICE 1
> -#endif
> -#endif /* CONFIG_MVSATA_IDE */
> -
> -/*
> - * Enable GPI0 support
> - */
> -#define CONFIG_KIRKWOOD_GPIO
> -
> -/*
> - * Enable I2C support
> - */
> -#ifdef CONFIG_CMD_I2C
> -/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
> -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
> -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
> -#if defined(CONFIG_NET2BIG_V2)
> -#define CONFIG_SYS_I2C_G762_ADDR 0x3e
> -#endif
> -#endif /* CONFIG_CMD_I2C */
> -
> -/*
> - * Partition support
> - */
> -
> -/*
> - * File systems support
> - */
> -
> -/*
> - * Environment variables configurations
> - */
> -
> -/*
> - * Default environment variables
> - */
> -#define CONFIG_BOOTCOMMAND \
> - "dhcp && run netconsole; " \
> - "if run usbload || run diskload; then bootm; fi"
> -
> -#define CONFIG_EXTRA_ENV_SETTINGS \
> - "stdin=serial\0" \
> - "stdout=serial\0" \
> - "stderr=serial\0" \
> - "bootfile=uImage\0" \
> - "loadaddr=0x800000\0" \
> - "autoload=no\0" \
> - "netconsole=" \
> - "set stdin $stdin,nc; " \
> - "set stdout $stdout,nc; " \
> - "set stderr $stderr,nc;\0" \
> - "diskload=ide reset && " \
> - "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
> - "usbload=usb start && " \
> - "fatload usb 0:1 $loadaddr /boot/$bootfile\0"
> -
> -#endif /* _CONFIG_LACIE_KW_H */
> --
> 2.25.1
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200619/7f85313c/attachment.sig>
More information about the U-Boot
mailing list