[U-Boot] [PULL] : Please pull u-boot-imx
Stefano Babic
sbabic at denx.de
Thu Apr 4 10:31:56 CEST 2013
Hi Albert,
last iMX fixes for the release. Please pull from u-boot-imx, thanks.
The following changes since commit b27673ccbd3d5435319b5c09c3e7061f559f925d:
Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'
(2013-03-15 20:50:43 +0100)
are available in the git repository at:
git://www.denx.de/git/u-boot-imx.git master
for you to fetch changes up to d36b39bf0d1dbe4ef03f7fc1f20b2e52eb90acf5:
spi: mxc_spi: Fix ECSPI reset handling (2013-04-04 10:23:09 +0200)
----------------------------------------------------------------
Abbas Raza (1):
mmc: i.MX6: fsl_esdhc: Define maximum bus width supported by a board
Alexandre Pereira da Silva (1):
mx23_olinuxino: Fix netboot console
Benoît Thébaudeau (1):
mx25pdk: Enable imxdi RTC
Dirk Behme (1):
spi: mxc_spi: Fix ECSPI reset handling
Eric Nelson (2):
i.MX6: Add hdmidet command to detect attached HDMI monitor
i.MX6: mx6qsabrelite: discard override of CONFIG_ARP_TIMEOUT
Fabio Estevam (10):
mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
configs: mx28evk: Use single-line comments
mx28evk: Disable CONFIG_CMD_I2C
Add initial support for Wandboard dual lite and solo.
mx28evk: Introduce a new target for saving env vars to NAND
mx6qsabrelite: README: No need to pass 'u-boot.imx'
mx6: Fix get_board_rev() for the mx6 solo case
wandboard: Remove duplicate 'mmc dev'
mx6qsabrelite: Remove duplicate 'mmc dev'
wandboard: Remove CONFIG_SYS_FSL_USDHC_NUM
Javier Martinez Canillas (1):
i.MX6: mx6qsabrelite: README: don't pass chip-select to sf probe
command
Knut Wohlrab (1):
imx-common: timer: fix 32-bit overflow
Otavio Salvador (4):
mx6qsabresd: Document the mapping of USDHC[2-4]
mx6qsabresd: Fix card detection for invalid card id case
mx6qsabre{sd,auto}: Add boot mode select
mx23_olinuxino: Change definitions to use spaces instead of tabs
MAINTAINERS | 1 +
arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c | 18 +--
arch/arm/cpu/armv7/mx6/soc.c | 12 ++
arch/arm/imx-common/Makefile | 1 +
arch/arm/imx-common/cmd_hdmidet.c | 37 +++++
arch/arm/imx-common/timer.c | 26 +--
arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 3 +
board/boundary/nitrogen6x/nitrogen6x.c | 8 +-
board/freescale/mx6qsabreauto/mx6qsabreauto.c | 18 +++
board/freescale/mx6qsabrelite/README | 4 +-
board/freescale/mx6qsabrelite/mx6qsabrelite.c | 8 +-
board/freescale/mx6qsabresd/mx6qsabresd.c | 48 ++++--
board/wandboard/Makefile | 29 ++++
board/wandboard/README | 40 +++++
board/wandboard/wandboard.c | 178 +++++++++++++++++++++
boards.cfg | 5 +-
doc/README.mx28evk | 18 +++
drivers/mmc/fsl_esdhc.c | 7 +
drivers/spi/mxc_spi.c | 8 +-
include/configs/mx23_olinuxino.h | 162 +++++++++----------
include/configs/mx25pdk.h | 4 +
include/configs/mx28evk.h | 92 ++++++-----
include/configs/mx6qsabre_common.h | 2 +
include/configs/mx6qsabrelite.h | 3 -
include/configs/wandboard.h | 209
+++++++++++++++++++++++++
include/fsl_esdhc.h | 1 +
26 files changed, 757 insertions(+), 185 deletions(-)
create mode 100644 arch/arm/imx-common/cmd_hdmidet.c
create mode 100644 board/wandboard/Makefile
create mode 100644 board/wandboard/README
create mode 100644 board/wandboard/wandboard.c
create mode 100644 include/configs/wandboard.h
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list