[U-Boot] [PULL] : Please pull u-boot-imx

Albert ARIBAUD albert.u.boot at aribaud.net
Thu Apr 4 12:31:54 CEST 2013


Hi Stefano,

On Thu, 04 Apr 2013 10:31:56 +0200, Stefano Babic <sbabic at denx.de>
wrote:

> Hi Albert,
> 
> last iMX fixes for the release. Please pull from u-boot-imx, thanks.
> 
> The following changes since commit b27673ccbd3d5435319b5c09c3e7061f559f925d:
> 
>   Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'
> (2013-03-15 20:50:43 +0100)
> 
> are available in the git repository at:
> 
> 
>   git://www.denx.de/git/u-boot-imx.git master
> 
> for you to fetch changes up to d36b39bf0d1dbe4ef03f7fc1f20b2e52eb90acf5:
> 
>   spi: mxc_spi: Fix ECSPI reset handling (2013-04-04 10:23:09 +0200)
> 
> ----------------------------------------------------------------
> Abbas Raza (1):
>       mmc: i.MX6: fsl_esdhc: Define maximum bus width supported by a board
> 
> Alexandre Pereira da Silva (1):
>       mx23_olinuxino: Fix netboot console
> 
> Benoît Thébaudeau (1):
>       mx25pdk: Enable imxdi RTC
> 
> Dirk Behme (1):
>       spi: mxc_spi: Fix ECSPI reset handling
> 
> Eric Nelson (2):
>       i.MX6: Add hdmidet command to detect attached HDMI monitor
>       i.MX6: mx6qsabrelite: discard override of CONFIG_ARP_TIMEOUT
> 
> Fabio Estevam (10):
>       mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
>       configs: mx28evk: Use single-line comments
>       mx28evk: Disable CONFIG_CMD_I2C
>       Add initial support for Wandboard dual lite and solo.
>       mx28evk: Introduce a new target for saving env vars to NAND
>       mx6qsabrelite: README: No need to pass 'u-boot.imx'
>       mx6: Fix get_board_rev() for the mx6 solo case
>       wandboard: Remove duplicate 'mmc dev'
>       mx6qsabrelite: Remove duplicate 'mmc dev'
>       wandboard: Remove CONFIG_SYS_FSL_USDHC_NUM
> 
> Javier Martinez Canillas (1):
>       i.MX6: mx6qsabrelite: README: don't pass chip-select to sf probe
> command
> 
> Knut Wohlrab (1):
>       imx-common: timer: fix 32-bit overflow
> 
> Otavio Salvador (4):
>       mx6qsabresd: Document the mapping of USDHC[2-4]
>       mx6qsabresd: Fix card detection for invalid card id case
>       mx6qsabre{sd,auto}: Add boot mode select
>       mx23_olinuxino: Change definitions to use spaces instead of tabs
> 
>  MAINTAINERS                                   |    1 +
>  arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c     |   18 +--
>  arch/arm/cpu/armv7/mx6/soc.c                  |   12 ++
>  arch/arm/imx-common/Makefile                  |    1 +
>  arch/arm/imx-common/cmd_hdmidet.c             |   37 +++++
>  arch/arm/imx-common/timer.c                   |   26 +--
>  arch/arm/include/asm/arch-mx6/mx6dl_pins.h    |    3 +
>  board/boundary/nitrogen6x/nitrogen6x.c        |    8 +-
>  board/freescale/mx6qsabreauto/mx6qsabreauto.c |   18 +++
>  board/freescale/mx6qsabrelite/README          |    4 +-
>  board/freescale/mx6qsabrelite/mx6qsabrelite.c |    8 +-
>  board/freescale/mx6qsabresd/mx6qsabresd.c     |   48 ++++--
>  board/wandboard/Makefile                      |   29 ++++
>  board/wandboard/README                        |   40 +++++
>  board/wandboard/wandboard.c                   |  178 +++++++++++++++++++++
>  boards.cfg                                    |    5 +-
>  doc/README.mx28evk                            |   18 +++
>  drivers/mmc/fsl_esdhc.c                       |    7 +
>  drivers/spi/mxc_spi.c                         |    8 +-
>  include/configs/mx23_olinuxino.h              |  162 +++++++++----------
>  include/configs/mx25pdk.h                     |    4 +
>  include/configs/mx28evk.h                     |   92 ++++++-----
>  include/configs/mx6qsabre_common.h            |    2 +
>  include/configs/mx6qsabrelite.h               |    3 -
>  include/configs/wandboard.h                   |  209
> +++++++++++++++++++++++++
>  include/fsl_esdhc.h                           |    1 +
>  26 files changed, 757 insertions(+), 185 deletions(-)
>  create mode 100644 arch/arm/imx-common/cmd_hdmidet.c
>  create mode 100644 board/wandboard/Makefile
>  create mode 100644 board/wandboard/README
>  create mode 100644 board/wandboard/wandboard.c
>  create mode 100644 include/configs/wandboard.h
> 
> 

Applied to u-boot-arm/master, thanks!

Amicalement,
-- 
Albert.


More information about the U-Boot mailing list