[U-Boot] [PATCH 2/3] wandboard: Add support for carrier board MicroSD card

Otavio Salvador otavio at ossystems.com.br
Mon Apr 15 19:00:03 CEST 2013


On Mon, Apr 15, 2013 at 1:40 PM, Fabio Estevam <festevam at gmail.com> wrote:
> On Mon, Apr 15, 2013 at 1:18 PM, Otavio Salvador
> <otavio at ossystems.com.br> wrote:
>
>> --- a/board/wandboard/wandboard.c
>> +++ b/board/wandboard/wandboard.c
>> @@ -162,13 +162,15 @@ int board_mmc_init(bd_t *bis)
>>                         gpio_direction_input(USDHC1_CD_GPIO);
>>                         break;
>>                 default:
>> -                       printf("Warning: you configured more USDHC controllers"
>> +                       printf("ERROR: you configured more USDHC controllers"
>>                                    "(%d) than supported by the board\n", i + 1);
>>                         return -EINVAL;
>>                 }
>>
>> -               if (fsl_esdhc_initialize(bis, &usdhc_cfg[i]))
>> -                       printf("Warning: failed to initialize mmc dev %d\n", i);
>> +               if (fsl_esdhc_initialize(bis, &usdhc_cfg[i])) {
>> +                       printf("ERROR: failed to initialize mmc dev %d\n", i);
>> +                       return 1;
>
> 1 is not an appropriate return value for an error.
>
> What about doing like sabrelite?
> status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
>
> and then you return status?

 int board_mmc_init(bd_t *bis)
 {
-       imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+       int i;
+       int ret;

-       usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-       usdhc_cfg[0].max_bus_width = 4;
-       gpio_direction_input(USDHC3_CD_GPIO);
+       /*
+        * According to the board_mmc_init() the following map is done:
+        * (U-boot device node)    (Physical Port)
+        * mmc0                    SOM MicroSD
+        * mmc1                    Carrier board MicroSD
+        */
+       for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+               switch (i) {
+               case 0:
+                       imx_iomux_v3_setup_multiple_pads(
+                               usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+                       usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+                       usdhc_cfg[0].max_bus_width = 4;
+                       gpio_direction_input(USDHC3_CD_GPIO);
+                       break;
+               case 1:
+                       imx_iomux_v3_setup_multiple_pads(
+                               usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+                       usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+                       usdhc_cfg[1].max_bus_width = 4;
+                       gpio_direction_input(USDHC1_CD_GPIO);
+                       break;
+               default:
+                       printf("ERROR: you configured more USDHC controllers"
+                                  "(%d) than supported by the board\n", i + 1);
+                       return -EINVAL;
+               }
+
+               ret |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+       }
+
+       if (ret)
+               printf("ERROR: failed to initialize mmc dev %d\n", i);

-       return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+       return ret;
 }

This would be the final patch than...

--
Otavio Salvador                             O.S. Systems
E-mail: otavio at ossystems.com.br  http://www.ossystems.com.br
Mobile: +55 53 9981-7854              http://projetos.ossystems.com.br


More information about the U-Boot mailing list