[U-Boot] [PATCH v2 15/15] fpga: Add support for loading bitstream for Xilinx Zynq
Michal Simek
michal.simek at xilinx.com
Tue Apr 23 12:46:14 CEST 2013
Devcfg device requires to load bitstream in binary format.
Signed-off-by: Joe Hershberger <joe.hershberger at ni.com>
Signed-off-by: Michal Simek <michal.simek at xilinx.com>
---
Changes in v2:
- Fix bugs reported by Tom Rini
- Fix checkpatch warnings (fpga)
- Fix comments (fpga)
- Do not use CamelCase for XilinxZynq (fpga)
arch/arm/cpu/armv7/zynq/slcr.c | 35 +++++
arch/arm/include/asm/arch-zynq/hardware.h | 10 +-
arch/arm/include/asm/arch-zynq/sys_proto.h | 3 +
board/xilinx/zynq/board.c | 37 +++++
drivers/fpga/Makefile | 1 +
drivers/fpga/xilinx.c | 37 +++++
drivers/fpga/zynqpl.c | 231 +++++++++++++++++++++++++++++
include/configs/zynq.h | 6 +
include/xilinx.h | 4 +
include/zynqpl.h | 59 ++++++++
10 files changed, 421 insertions(+), 2 deletions(-)
create mode 100644 drivers/fpga/zynqpl.c
create mode 100644 include/zynqpl.h
diff --git a/arch/arm/cpu/armv7/zynq/slcr.c b/arch/arm/cpu/armv7/zynq/slcr.c
index 5a8674a..52048c6 100644
--- a/arch/arm/cpu/armv7/zynq/slcr.c
+++ b/arch/arm/cpu/armv7/zynq/slcr.c
@@ -28,6 +28,9 @@
#define SLCR_LOCK_MAGIC 0x767B
#define SLCR_UNLOCK_MAGIC 0xDF0D
+#define SLCR_IDCODE_MASK 0x1F000
+#define SLCR_IDCODE_SHIFT 12
+
static int slcr_lock = 1; /* 1 means locked, 0 means unlocked */
void zynq_slcr_lock(void)
@@ -87,3 +90,35 @@ void zynq_slcr_gem_clk_setup(u32 gem_id, u32 rclk, u32 clk)
out:
zynq_slcr_lock();
}
+
+void zynq_slcr_devcfg_disable(void)
+{
+ zynq_slcr_unlock();
+
+ /* Disable AXI interface */
+ writel(0xFFFFFFFF, &slcr_base->fpga_rst_ctrl);
+
+ /* Set Level Shifters DT618760 */
+ writel(0xA, &slcr_base->lvl_shftr_en);
+
+ zynq_slcr_lock();
+}
+
+void zynq_slcr_devcfg_enable(void)
+{
+ zynq_slcr_unlock();
+
+ /* Set Level Shifters DT618760 */
+ writel(0xF, &slcr_base->lvl_shftr_en);
+
+ /* Disable AXI interface */
+ writel(0x0, &slcr_base->fpga_rst_ctrl);
+
+ zynq_slcr_lock();
+}
+
+u32 zynq_slcr_get_idcode(void)
+{
+ return (readl(&slcr_base->pss_idcode) & SLCR_IDCODE_MASK) >>
+ SLCR_IDCODE_SHIFT;
+}
diff --git a/arch/arm/include/asm/arch-zynq/hardware.h b/arch/arm/include/asm/arch-zynq/hardware.h
index 6af892a..8b8a91a 100644
--- a/arch/arm/include/asm/arch-zynq/hardware.h
+++ b/arch/arm/include/asm/arch-zynq/hardware.h
@@ -53,11 +53,17 @@ struct slcr_regs {
u32 boot_mode; /* 0x25c */
u32 reserved4[116];
u32 trust_zone; /* 0x430 */ /* FIXME */
- u32 reserved5[115];
+ u32 reserved5_1[63];
+ u32 pss_idcode; /* 0x530 */
+ u32 reserved5_2[51];
u32 ddr_urgent; /* 0x600 */
u32 reserved6[6];
u32 ddr_urgent_sel; /* 0x61c */
- u32 reserved7[188];
+ u32 reserved7[56];
+ u32 mio_pin[54]; /* 0x700 - 0x7D4 */
+ u32 reserved8[74];
+ u32 lvl_shftr_en; /* 0x900 */
+ u32 reserved9[3];
u32 ocm_cfg; /* 0x910 */
};
diff --git a/arch/arm/include/asm/arch-zynq/sys_proto.h b/arch/arm/include/asm/arch-zynq/sys_proto.h
index af9e7f8..2317121 100644
--- a/arch/arm/include/asm/arch-zynq/sys_proto.h
+++ b/arch/arm/include/asm/arch-zynq/sys_proto.h
@@ -27,6 +27,9 @@ extern void zynq_slcr_lock(void);
extern void zynq_slcr_unlock(void);
extern void zynq_slcr_cpu_reset(void);
extern void zynq_slcr_gem_clk_setup(u32 gem_id, u32 rclk, u32 clk);
+extern void zynq_slcr_devcfg_disable(void);
+extern void zynq_slcr_devcfg_enable(void);
+extern u32 zynq_slcr_get_idcode(void);
/* Driver extern functions */
extern int zynq_sdhci_init(u32 regbase);
diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
index 1589d21..b02c364 100644
--- a/board/xilinx/zynq/board.c
+++ b/board/xilinx/zynq/board.c
@@ -22,15 +22,52 @@
#include <common.h>
#include <netdev.h>
+#include <zynqpl.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_FPGA
+Xilinx_desc fpga;
+
+/* It can be done differently */
+Xilinx_desc fpga010 = XILINX_XC7Z010_DESC(0x10);
+Xilinx_desc fpga020 = XILINX_XC7Z020_DESC(0x20);
+Xilinx_desc fpga030 = XILINX_XC7Z030_DESC(0x30);
+Xilinx_desc fpga045 = XILINX_XC7Z045_DESC(0x45);
+#endif
+
int board_init(void)
{
+#ifdef CONFIG_FPGA
+ u32 idcode;
+
+ idcode = zynq_slcr_get_idcode();
+
+ switch (idcode) {
+ case XILINX_ZYNQ_7010:
+ fpga = fpga010;
+ break;
+ case XILINX_ZYNQ_7020:
+ fpga = fpga020;
+ break;
+ case XILINX_ZYNQ_7030:
+ fpga = fpga030;
+ break;
+ case XILINX_ZYNQ_7045:
+ fpga = fpga045;
+ break;
+ }
+#endif
+
icache_enable();
+#ifdef CONFIG_FPGA
+ fpga_init();
+ fpga_add(fpga_xilinx, &fpga);
+#endif
+
return 0;
}
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index b48f623..0b51dcd 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -30,6 +30,7 @@ COBJS-y += fpga.o
COBJS-$(CONFIG_FPGA_SPARTAN2) += spartan2.o
COBJS-$(CONFIG_FPGA_SPARTAN3) += spartan3.o
COBJS-$(CONFIG_FPGA_VIRTEX2) += virtex2.o
+COBJS-$(CONFIG_FPGA_ZYNQPL) += zynqpl.o
COBJS-$(CONFIG_FPGA_XILINX) += xilinx.o
COBJS-$(CONFIG_FPGA_LATTICE) += ivm_core.o lattice.o
ifdef CONFIG_FPGA_ALTERA
diff --git a/drivers/fpga/xilinx.c b/drivers/fpga/xilinx.c
index 32787b2..fe324ab 100644
--- a/drivers/fpga/xilinx.c
+++ b/drivers/fpga/xilinx.c
@@ -1,4 +1,6 @@
/*
+ * (C) Copyright 2012-2013, Xilinx, Michal Simek
+ *
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland at enterasys.com.
* Keith Outwater, keith_outwater at mvis.com
@@ -31,6 +33,7 @@
#include <virtex2.h>
#include <spartan2.h>
#include <spartan3.h>
+#include <zynqpl.h>
#if 0
#define FPGA_DEBUG
@@ -86,6 +89,16 @@ int xilinx_load(Xilinx_desc *desc, const void *buf, size_t bsize)
__FUNCTION__);
#endif
break;
+ case xilinx_zynq:
+#if defined(CONFIG_FPGA_ZYNQPL)
+ PRINTF("%s: Launching the Zynq PL Loader...\n",
+ __func__);
+ ret_val = zynq_load(desc, buf, bsize);
+#else
+ printf("%s: No support for Zynq devices.\n",
+ __func__);
+#endif
+ break;
default:
printf ("%s: Unsupported family type, %d\n",
@@ -133,6 +146,16 @@ int xilinx_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
__FUNCTION__);
#endif
break;
+ case xilinx_zynq:
+#if defined(CONFIG_FPGA_ZYNQPL)
+ PRINTF("%s: Launching the Zynq PL Reader...\n",
+ __func__);
+ ret_val = zynq_dump(desc, buf, bsize);
+#else
+ printf("%s: No support for Zynq devices.\n",
+ __func__);
+#endif
+ break;
default:
printf ("%s: Unsupported family type, %d\n",
@@ -158,6 +181,9 @@ int xilinx_info (Xilinx_desc * desc)
case Xilinx_Virtex2:
printf ("Virtex-II\n");
break;
+ case xilinx_zynq:
+ printf("Zynq PL\n");
+ break;
/* Add new family types here */
default:
printf ("Unknown family type, %d\n", desc->family);
@@ -183,6 +209,9 @@ int xilinx_info (Xilinx_desc * desc)
case master_selectmap:
printf ("Master SelectMap Mode\n");
break;
+ case devcfg:
+ printf("Device configuration interface (Zynq)\n");
+ break;
/* Add new interface types here */
default:
printf ("Unsupported interface type, %d\n", desc->iface);
@@ -222,6 +251,14 @@ int xilinx_info (Xilinx_desc * desc)
__FUNCTION__);
#endif
break;
+ case xilinx_zynq:
+#if defined(CONFIG_FPGA_ZYNQPL)
+ zynq_info(desc);
+#else
+ /* just in case */
+ printf("%s: No support for Zynq devices.\n",
+ __func__);
+#endif
/* Add new family types here */
default:
/* we don't need a message here - we give one up above */
diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c
new file mode 100644
index 0000000..0365803
--- /dev/null
+++ b/drivers/fpga/zynqpl.c
@@ -0,0 +1,231 @@
+/*
+ * (C) Copyright 2012-2013, Xilinx, Michal Simek
+ *
+ * (C) Copyright 2012
+ * Joe Hershberger <joe.hershberger at ni.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <zynqpl.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+
+#define DEVCFG_CTRL_PCFG_PROG_B 0x40000000
+#define DEVCFG_ISR_FATAL_ERROR_MASK 0x00740040
+#define DEVCFG_ISR_ERROR_FLAGS_MASK 0x00340840
+#define DEVCFG_ISR_RX_FIFO_OV 0x00040000
+#define DEVCFG_ISR_DMA_DONE 0x00002000
+#define DEVCFG_ISR_PCFG_DONE 0x00000004
+#define DEVCFG_STATUS_DMA_CMD_Q_F 0x80000000
+#define DEVCFG_STATUS_DMA_CMD_Q_E 0x40000000
+#define DEVCFG_STATUS_DMA_DONE_CNT_MASK 0x30000000
+#define DEVCFG_STATUS_PCFG_INIT 0x00000010
+#define DEVCFG_MCTRL_RFIFO_FLUSH 0x00000002
+#define DEVCFG_MCTRL_WFIFO_FLUSH 0x00000001
+
+#ifndef CONFIG_SYS_FPGA_WAIT
+#define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100 /* 10 ms */
+#endif
+
+#ifndef CONFIG_SYS_FPGA_PROG_TIME
+#define CONFIG_SYS_FPGA_PROG_TIME CONFIG_SYS_HZ /* 1 s */
+#endif
+
+int zynq_info(Xilinx_desc *desc)
+{
+ return FPGA_SUCCESS;
+}
+
+/* Xilinx binary format header */
+static const u32 bin_format[] = {
+ 0xffffffff, /* Dummy words */
+ 0xffffffff,
+ 0xffffffff,
+ 0xffffffff,
+ 0xffffffff,
+ 0xffffffff,
+ 0xffffffff,
+ 0xffffffff,
+ 0x000000bb, /* Sync word */
+ 0x11220044, /* Sync word */
+ 0xffffffff,
+ 0xffffffff,
+ 0xaa995566, /* Sync word */
+};
+
+int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize)
+{
+ unsigned long ts; /* Timestamp */
+ u32 control;
+ u32 isr_status;
+ u32 status;
+ const u32 *test = buf;
+ int i;
+
+ if ((u32)buf & 0x3) {
+ printf("Error: Buffer is not aligned %x\n", (u32)buf);
+ return FPGA_FAIL;
+ }
+
+ /* Check bitstream size */
+ if (bsize != desc->size) {
+ printf("Error: File size is wrong - should be %x.\n",
+ desc->size);
+ return FPGA_FAIL;
+ }
+
+ /* Checking that passing bin is not a bitstream */
+ for (i = 0; i < ARRAY_SIZE(bin_format); i++) {
+ if (test[i] != bin_format[i]) {
+ puts("Error: File not in binary format.\n");
+ return FPGA_FAIL;
+ }
+ }
+
+ zynq_slcr_devcfg_disable();
+
+ /* Setting PCFG_PROG_B signal to high */
+ control = readl(&devcfg_base->ctrl);
+ writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
+ /* Setting PCFG_PROG_B signal to low */
+ writel(control & ~DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
+
+ /* Polling the PCAP_INIT status for Reset */
+ ts = get_timer(0);
+ while (readl(&devcfg_base->status) & DEVCFG_STATUS_PCFG_INIT) {
+ if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
+ puts("Error: Timeout waiting for INIT to clear.\n");
+ return FPGA_FAIL;
+ }
+ }
+
+ /* Setting PCFG_PROG_B signal to high */
+ writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
+
+ /* Polling the PCAP_INIT status for Set */
+ ts = get_timer(0);
+ while (!(readl(&devcfg_base->status) & DEVCFG_STATUS_PCFG_INIT)) {
+ if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
+ puts("Error: Timeout waiting for INIT to set.\n");
+ return FPGA_FAIL;
+ }
+ }
+
+ isr_status = readl(&devcfg_base->int_sts);
+
+ /* Clear it all, so if Boot ROM comes back, it can proceed */
+ writel(0xFFFFFFFF, &devcfg_base->int_sts);
+
+ if (isr_status & DEVCFG_ISR_FATAL_ERROR_MASK) {
+ debug("Fatal errors in PCAP 0x%X\n", isr_status);
+
+ /* If RX FIFO overflow, need to flush RX FIFO first */
+ if (isr_status & DEVCFG_ISR_RX_FIFO_OV) {
+ writel(DEVCFG_MCTRL_RFIFO_FLUSH, &devcfg_base->mctrl);
+ writel(0xFFFFFFFF, &devcfg_base->int_sts);
+ }
+ return FPGA_FAIL;
+ }
+
+ status = readl(&devcfg_base->status);
+
+ debug("status = 0x%08X\n", status);
+
+ if (status & DEVCFG_STATUS_DMA_CMD_Q_F) {
+ debug("Error: device busy\n");
+ return FPGA_FAIL;
+ }
+
+ debug("device ready\n");
+
+ if (!(status & DEVCFG_STATUS_DMA_CMD_Q_E)) {
+ if (!(readl(&devcfg_base->int_sts) & DEVCFG_ISR_DMA_DONE)) {
+ /* Error state, transfer cannot occur */
+ debug("isr indicates error\n");
+ return FPGA_FAIL;
+ } else {
+ /* Clear out the status */
+ writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
+ }
+ }
+
+ if (status & DEVCFG_STATUS_DMA_DONE_CNT_MASK) {
+ /* Clear the count of completed DMA transfers */
+ writel(DEVCFG_STATUS_DMA_DONE_CNT_MASK, &devcfg_base->status);
+ }
+
+ debug("Source = 0x%08X\n", (u32)buf);
+ debug("Size = %zu\n", bsize);
+
+ /* Set up the transfer */
+ writel((u32)buf | 1, &devcfg_base->dma_src_addr);
+ writel(0xFFFFFFFF, &devcfg_base->dma_dst_addr);
+ writel(bsize >> 2, &devcfg_base->dma_src_len);
+ writel(0, &devcfg_base->dma_dst_len);
+
+ isr_status = readl(&devcfg_base->int_sts);
+
+ /* Polling the PCAP_INIT status for Set */
+ ts = get_timer(0);
+ while (!(isr_status & DEVCFG_ISR_DMA_DONE)) {
+ if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) {
+ debug("Error: isr = 0x%08X\n", isr_status);
+ debug("Write count = 0x%08X\n",
+ readl(&devcfg_base->write_count));
+ debug("Read count = 0x%08X\n",
+ readl(&devcfg_base->read_count));
+
+ return FPGA_FAIL;
+ }
+ if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) {
+ puts("Error: Timeout waiting for DMA to complete.\n");
+ return FPGA_FAIL;
+ }
+ isr_status = readl(&devcfg_base->int_sts);
+ }
+
+ debug("DMA transfer is done\n");
+
+ /* Check FPGA configuration completion */
+ ts = get_timer(0);
+ while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
+ if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
+ puts("Error: Timeout waiting for FPGA to config.\n");
+ return FPGA_FAIL;
+ }
+ isr_status = readl(&devcfg_base->int_sts);
+ }
+
+ debug("FPGA config done\n");
+
+ /* Clear out the DMA status */
+ writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
+
+ zynq_slcr_devcfg_enable();
+
+ return FPGA_SUCCESS;
+}
+
+int zynq_dump(Xilinx_desc *desc, const void *buf, size_t bsize)
+{
+ return FPGA_FAIL;
+}
diff --git a/include/configs/zynq.h b/include/configs/zynq.h
index f1f182e..38f04f6 100644
--- a/include/configs/zynq.h
+++ b/include/configs/zynq.h
@@ -88,6 +88,12 @@
# define CONFIG_CPU_V6 /* Required by CONFIG_ARM_DCC */
#endif
+/* Enable the PL to be downloaded */
+#define CONFIG_FPGA
+#define CONFIG_FPGA_XILINX
+#define CONFIG_FPGA_ZYNQPL
+#define CONFIG_CMD_FPGA
+
#define CONFIG_BOOTP_SERVERIP
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
diff --git a/include/xilinx.h b/include/xilinx.h
index 5f25b7a..592cbea 100644
--- a/include/xilinx.h
+++ b/include/xilinx.h
@@ -33,10 +33,12 @@
#define CONFIG_SYS_VIRTEX_E CONFIG_SYS_FPGA_DEV( 0x2 )
#define CONFIG_SYS_VIRTEX2 CONFIG_SYS_FPGA_DEV( 0x4 )
#define CONFIG_SYS_SPARTAN3 CONFIG_SYS_FPGA_DEV( 0x8 )
+#define CONFIG_SYS_ZYNQ CONFIG_SYS_FPGA_DEV(0x10)
#define CONFIG_SYS_XILINX_SPARTAN2 (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_SPARTAN2)
#define CONFIG_SYS_XILINX_VIRTEX_E (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_VIRTEX_E)
#define CONFIG_SYS_XILINX_VIRTEX2 (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_VIRTEX2)
#define CONFIG_SYS_XILINX_SPARTAN3 (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_SPARTAN3)
+#define CONFIG_SYS_XILINX_ZYNQ (CONFIG_SYS_FPGA_XILINX | CONFIG_SYS_ZYNQ)
/* XXX - Add new models here */
@@ -59,6 +61,7 @@ typedef enum { /* typedef Xilinx_iface */
jtag_mode, /* jtag/tap serial (not used ) */
master_selectmap, /* master SelectMap (virtex2) */
slave_selectmap, /* slave SelectMap (virtex2) */
+ devcfg, /* devcfg interface (zynq) */
max_xilinx_iface_type /* insert all new types before this */
} Xilinx_iface; /* end, typedef Xilinx_iface */
@@ -68,6 +71,7 @@ typedef enum { /* typedef Xilinx_Family */
Xilinx_VirtexE, /* Virtex-E Family */
Xilinx_Virtex2, /* Virtex2 Family */
Xilinx_Spartan3, /* Spartan-III Family */
+ xilinx_zynq, /* Zynq Family */
max_xilinx_type /* insert all new types before this */
} Xilinx_Family; /* end, typedef Xilinx_Family */
diff --git a/include/zynqpl.h b/include/zynqpl.h
new file mode 100644
index 0000000..bc9b948
--- /dev/null
+++ b/include/zynqpl.h
@@ -0,0 +1,59 @@
+/*
+ * (C) Copyright 2012-2013, Xilinx, Michal Simek
+ *
+ * (C) Copyright 2012
+ * Joe Hershberger <joe.hershberger at ni.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ZYNQPL_H_
+#define _ZYNQPL_H_
+
+#include <xilinx.h>
+
+extern int zynq_load(Xilinx_desc *desc, const void *image, size_t size);
+extern int zynq_dump(Xilinx_desc *desc, const void *buf, size_t bsize);
+extern int zynq_info(Xilinx_desc *desc);
+
+#define XILINX_ZYNQ_7010 0x2
+#define XILINX_ZYNQ_7020 0x7
+#define XILINX_ZYNQ_7030 0xc
+#define XILINX_ZYNQ_7045 0x11
+
+/* Device Image Sizes */
+#define XILINX_XC7Z010_SIZE 16669920/8
+#define XILINX_XC7Z020_SIZE 32364512/8
+#define XILINX_XC7Z030_SIZE 47839328/8
+#define XILINX_XC7Z045_SIZE 106571232/8
+
+/* Descriptor Macros */
+#define XILINX_XC7Z010_DESC(cookie) \
+{ xilinx_zynq, devcfg, XILINX_XC7Z010_SIZE, NULL, cookie }
+
+#define XILINX_XC7Z020_DESC(cookie) \
+{ xilinx_zynq, devcfg, XILINX_XC7Z020_SIZE, NULL, cookie }
+
+#define XILINX_XC7Z030_DESC(cookie) \
+{ xilinx_zynq, devcfg, XILINX_XC7Z030_SIZE, NULL, cookie }
+
+#define XILINX_XC7Z045_DESC(cookie) \
+{ xilinx_zynq, devcfg, XILINX_XC7Z045_SIZE, NULL, cookie }
+
+#endif /* _ZYNQPL_H_ */
--
1.8.2.1
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 198 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130423/a5744c53/attachment.pgp>
More information about the U-Boot
mailing list